Siemens Sn 25m230 Quick Guide

							Start Reset 3sec.
h
8
Filling the salt dispenser
Adding rinse aid
Adding detergent
Select programme
Brief and handy: 
everything your dishwasher 
needs …
Before using for the first time, 
read the Installation instructions 
and Operating instructions!
54 3 21
6
97
Summary of instructions Dishwasher
en
Switching on the appliance
Switch off the appliance 
Everything o.k....
Start programme
Here we go...
9000 397 652(9001) 640 MA
Ask  your water 
supply company 
what the water 
hardness
is and enter...Adjusting the water softening system*
Quickly sorted ...
* only before the first 
wash or if the water 
hardness has been 
changedHow to adjust
B
A
C
– Switch on ON/OFF switch.
– Hold down programme button A and press START button until H:0... 
   is indicated on the digital display.
– Release both buttons. 
   The LED for button A flashes and the factory set value of H:04 
   is indicated on the digital display.
– Press programme buttonC.
  Each time the button is pressed the set value increases by one setting; 
   when the value reaches H:07, the display jumps back toH:00 (off).
– Press START button. The chosen setting has now been stored. 
• ‹‹
• ‹‚
• ‹ƒ
• ‹„
• ‹…
• ‹†
• ‹‡
• ‹ˆ:
:
:
:
:
:
:
:
0-8
9-10
11-12
13-15
16-20
21-26
27-38
39-620 -1.1
1.2-1.4
1.5-1.8
1.9-2.1
2.2-2.9
3.0-3.7
3.8-5.4
5.5-8.9
Water 
hardness 
value 
°ClarkeHardness
rangemmol/lFactory 
setting
soft
soft
medium
medium
medium
hard
hard
hard
Dissolves limescale (not necessary for set value 0!) ...
$
Unscrew 
cover.Fill the salt 
dispenser with 
water before 
the first wash only.Add special salt 
(never add 
detergent!).Screw on 
the cover. 
Wash 
immediately.
Spick and span ...
%
Press 
mark 1, 
lift up 
cover 2.Fill in 
rinse aid.Screw on 
the cover. 
CLICK!
21
A lot of dirt, a lot of detergent ...
7
If required, 
open the cover 
(press button).Attention: 
Combination 
products 
are not suitable 
for all programmes, 
follow 
manufacturer’s 
instructions.Pour detergent
into the dry 
detergent 
dispenser only.Slide cover 
shut, press. 
PLOP!
15 ml 25 ml 50 ml
Overview of programmes
The max. possible number of programmes 
is illustrated in this overview. 
The corresponding programmes for your appliance 
can be found on the fascia. 
The programme data has been measured 
in the laboratory according to European 
standard EN 50242. 
Deviations are possible in practice. 
* half normal loadQuick, economical or intensive ...
Prerinse Quick
45° Gentle
40° Eco
50° Auto
45°–65° Intensive
70°
Energy consumption in kWh
With Aquasensor Water consumption in litres Duration: hs : mins
±
Á
á
éñ
ù
àðø
²
ê2:15 1:35-2:30 2:20 1:10 0:29  * 0:15
1,50 1,00-1,60 1,05 0,80 0,80 0,05
15 - 12 13 10 4
12 9-19 - 10 - -
Additional options**
Flexibility…
Express Wash 
... is obtained by increased 
energy consumption 
at a constant cleaning 
performance. 
Half load 
... for a few items, 
saves water, energy 
and time.Extra drying 
... improves the drying 
result by increased 
temperature 
in the final rinse.  
(Please take care 
with delicate dishes.) Hygiene
... the temperature 
is increased during 
the final rinse process. 
This increases 
the hygiene status. Intensive zone 
... perfect for 
a mixed load. 
Washing pressure 
and washing temperature 
are increased slightly.
** depending on model
Ÿ
§Ï
·¿
 
						

							Maintenance and care
Cleaning waste water pump
1
23
CLICK!
A
B For perfect rinsing results ...
Filters
... check, 
if required, 
clean.Rotate 
filter cylinder, 
remove filter 
system...rinse 
under 
running 
water ...insert ...Screw on 
filter system 
NOTE 
MARK!
Spray arms 
...Remove 
blockages/ 
deposits.pull lower arm 
upwards...unscrew 
upper arm …clean spray nozzles 
under running water 
(if required 
use toothpicks) ...insert 
lower arm ...
screw on upper 
arm tightly– Pull out the mains plug.
– Remove filters and scoop out water.
– Lever off cover (A).
– Check area around the fan impeller 
   for foreign objects.
– Click cover shut (B).
– Insert filters.
Rectifying minor faults yourself ...
... as it is worth doing it yourself!
Fault Possible causesRemedial action
Display “6” is litSupply fitting jammed or calcified
1. Unscrew water connection.
2. Clean filter in the water connection.
3. Flow rate must be min. 10l/min.,
when water supply is open.
If the flow rate is less, replace the supply fitting. Open supply fitting.
Install supply hose without kinks.
Display “E:25” 
and “6” are litWaste water pump blockedClean waste-water pump (see above).
Rust on the cutleryCutlery not rust-resistant
Hard knife blades are more susceptible
Extraneous rust Use dishwasher-proof cutlery.
Never wash rusting parts in the appliance. Other fault display 
“E:XX” is lit Display “E:24” 
and “6” are lit
Residual water 
in the applianceAppliance has technical defectWaste water hose is blocked 
or kinked
Cover not attached to waste 
water pump
Call factory customer service (state fault display).
Unplug appliance.Install waste water hose without kinks.
Attach cover (see above).
The programme has not yet ended
Close the appliance and switch it on or terminate 
the programme (see Terminating the programme).
Fault Possible causesRemedial action
More information can be found in the operating instructions
Utensils are not clean
Sand or gritty residue 
on the utensilsUtensils are situated close together 
or one above the other
Too little detergent
Unsuitable programme selected
Spray arm nozzles blocked
Filters dirty, not seated firmly
Spray arms blockedSeparate the utensils, prevent contact points.
Follow manufacturer’s instructions (detergent).
Select a more intensive programme.
Clean the spray arms (see above).
Clean the filters (see above).
Arrange the utensils so that the spray 
arms can rotate freely.
Stains and streaks
Milky deposits 
on the utensils 
(can be removed)
Milky deposits, glasses 
cloudy/tarnished 
(cannot be removed)
Plastic/utensils 
discoloured Rinse aid dosage too high/too low
Water softening system incorrectly set
No salt
Glasses not dishwasher-proof
Too little detergent
Discoloration caused by food colourings 
(tomato sauce)Streaks: reduce dosage.
Water or limescale stains: increase dosage.
Correctly set water softening system.
Refill with special salt.
Use dishwasher- proof glasses.
Use a detergent suitable for glasses. 
Follow manufacturer’s instructions (detergent).
Discoloration is harmless; 
subsequent rinse cycles will cause it to fade.
Utensils not dryRinse aid Increase dosage.
Change the product.
The combined detergent used 
has a poor drying performance Use rinse aid.
Appliance settingActivate intensive drying (depending on model).
Dishwasher-proof utensils (not soiled with ash, wax, lubricating grease, ink 
or adhesive labels; remove large remnants of jam, milk products and food 
according to the operating instructions and check that the spray arms can rotate freely. While the programme is running, 
press the START button 
for approx. 3 sec. (Reset).The numerical display 
indicates “0:01”; 
approx. 1 minute after 
the programme ends, 
“0:00” is indicated.Switch off the appliance.
Terminating the programme ...Loading the dishwasher correctly ...