Siemens Smv 40e10 Operating Instructions

							en
11
Small accessories holder *Sma
ll a
ccessor
ie
s
 h
o
ld
er
* depending on model 
Light-weight plastic accessories, e.g. cups,  
lids, etc. can be held securely in the small  
accessories holder.
Knife shelf *Kn
ife
 she
lf
* depending on model 
Long knives and other utensils can be  
arranged horizontally.
Ad
ju
s
tin
g
 th
e
 h
e
ig
h
t o
f
 th
e
 b
asketAdjusting the height of the 
basket *
* depending on model 
If required, the height of the upper utensils  
basket  1 can be adjusted to provide 
more space for tall utensils either in the  
upper or lower basket. 
Appliance height 81.5 cm 
Appliance height 86.5 cm 
Select one of the two following procedures  
according to the design of the top basket  
for your appliance model:
Top basket Bottom 
basket
Setting 1 max. ø 22 cm 30 cm 
Setting 2 max. ø 24.5 cm 27.5 cm 
Setting 3 max. ø 27 cm 25 cm
Top basket Bottom basket
Setting 1 max. ø 24 cm 33 cm 
Setting 2 max. ø 26.5 cm 30.5 cm 
Setting 3 max. ø 29 cm 28 cm
  
						

							en
12
Top basket with side levers
– Pull out the top basket 1 out. 
–To  lower the basket, press in the left 
and then the right lever on the outside  
of the basket. In doing so, hold the  
sides of the basket along the upper 
edge to prevent it from suddenly 
dropping.
–To  raise the basket, hold the basket on 
the sides of the upper edge and lift it  
up.
– Before re-inserting the basket again,  ensure that it is at the  same height on 
both sides. Otherwise, the appliance  
door cannot be closed and the upper  
spray arm will not be connected to the  
water circuit. 
Top basket with  upper and lower 
roller pairs
– Pull out the top basket  1 out. 
– Remove the upper basket and re- attach it to the upper (stage 3) or lower 
(stage 1) rollers. You can use tablets as well as powder 
or liquid detergents for dishwashers, but 
never use washing up liquid. The dosage  
can be individually adjusted with powder  
or a liquid detergent according 
to the degree of soiling. Tablets contain 
an adequately large amount of active  
ingredients for all cleaning tasks. Modern,  
powerful detergents predominantly 
use a low-alkaline formulation with  
phosphate and enzymes. Phosphates  
bond the lime in the water. Enzymes break 
down starch and remove protein. 
Phosphate-free detergents are less  
frequent. These have a slightly weaker  
lime bonding capacity and require 
a higher dosage. To remove coloured  
stains (e.g. tea, tomato sauce), oxygen- 
based bleaching agents are usually used. 
Note 
To ensure a good washing result, always  
follow the instructions on the detergent  
packaging! 
If you have further questions,  
we recommend that you contact  
the detergent manufacturers’ helpline.
ã=Warning
Read and observe the safety information  
and instructions for use on the packaging  
for cleaning and rinsing agents.
Detergent
   
						

							en
13
Adding detergent
– If the detergent dispenser 9 is still 
closed, press the lock  9* to open the 
detergent dispenser. 
Pour detergent into the dry detergent  
dispenser 9 only (insert tablet flat, 
not on its edge). 
Dosage: see manufacturer’s  
instructions on the packaging.  
The graduated detergent  
dispenser 9 helps you add the 
correct amount of powder or liquid  
detergent. 
Usually 20 ml–25 ml are adequate  
for normal soiling. If using tablets, one  
tablet is adequate.
– Close the cover on the detergent  dispenser by sliding it up until the lock  
engages without difficulty. 
The detergent dispenser opens  
automatically at the optimum time 
depending on the programme.  
The powder or liquid detergent  
is distributed in the appliance and is 
dissolved, the tablet falls into the tablet 
collecting tray where it dissolves  
in doses. Tip 
If the utensils are only lightly soiled, slightly  
less than the indicated amount 
of detergent is usually adequate.  
Suitable detergents and care products  
can be purchased online via our website 
or via customer service (see back page). 
Combination detergent
Apart from conventional detergents (Solo), 
a number of products are offered with 
additional functions. These products 
contain not only the detergent but also  
rinse-aid and salt replacement substances  
(3in1) and, depending on the combination 
(4in1, 5in1, etc.), additional components 
such as glass protection or stainless steel 
cleaner. Combination detergents function 
only up to a specific degree of hardness  
(usually 26° Clarke). Over this limit salt  
and rinse-aid must be added.  
As soon as combined detergents  
are used, the rinse programme is adjusted  
automatically to ensure the best possible  
rinsing and drying result.
ã=Warnings
–Do  not place small parts for washing in 
the tablet collecting tray  12; this 
prevents the tablet from dissolving  
evenly.
– If you want to add more utensils after  the programme has started, do  not 
use the tablet collecting tray 12 
as a handle for the upper basket. 
The tablet could already be there and 
you will touch the partially dissolved 
tablet.



 
						

							en
14
Notes 
– You will obtain optimum rinsing 
and drying results by using solo  
detergents and applying salt and rinse 
aid separately.
– If programmes are short, tablets  may not have full cleaning effect due to  
different dissolving properties 
and there may even be undissolved 
detergent residue. It is recommended  
to use washing powder for these  
programmes.
– The Intensive programme (on some  models) requires one tab only. When  
using washing powder, you can apply  
some of this cleaning agent to the 
inside of the appliance’s door.
– Even if the rinse-aid and/or salt refill  indicator is lit, the rinse programme will 
run correctly with combined 
detergents.
– If using detergents in a water-soluble  protective cover: Take hold of the 
cover with dry hands only and put 
the detergent into an absolutely 
dry detergent dispenser only, otherwise 
the detergent may stick.
– If you switch from combined  detergents to solo detergents, ensure 
that the water softening system and 
amount of rinse aid have been set to 
the correct value.
 
						

							en
15
The max. possible number of programmes is illustrated 
in this overview. 
The corresponding programmes for your appliance can be  found on the fascia.
Programme selection
You can select a suitable programme  
according to the type of utensils and  
degree of soiling.
Information for test institutes
Test institutes can request the conditions  
for running comparison tests by sending  
an e-mail to  
[email protected].  
Quote the appliance number (E­Nr.) 
and the production date (FD) which you  
can find on the rating  
plate 92on the appliance door.
Overview of programmes
Type of utensils Type of soiling Programme Possible additional 
optionsProgramme sequence
pots and pans,  non-sensitive  utensils 
and cutlery very adhesive 
burned-in or dried-on  food remnants 
containing starch 
or protein
±  / °
Intensive 70°
allPrerinse
Clean 70°
Intermediate rinse
Final rinse 65° Dry
Ù / Ø
Normal 65° Prerinse
Clean 65°
Intermediate rinse Final rinse 65°
Dry
mixed utensils  and cutlery part dried, common 
household food  remnants
á  / à
Eco 50° Prerinse
Clean 50°
Intermediate rinse Final rinse 65° Dry
sensitive utensils,  cutlery, 
temperature-
sensitive plastic 
and glasses slightly adhesive, 
fresh food remnants
é  / è
Gentle 40° Intensive zone
Express Wash/  Speed Perfect  (VarioSpeed)
Half load
Extra drying Prerinse
Clean 40°
Intermediate rinse Final rinse 55°
Dry
ñ / ð
Quick 45° Extra drying Clean 45°
Intermediate rinse
Final rinse 55°
all types of utensils cold rinsing, 
intermediate 
cleaning
ù  / ø
Prerinse none Prerinse
 
						

							en
16
* depending on model 
Additional options can be set with the  
buttons 
8.
Express
 W
ash
/ S
peed
 P
e
rf
ec
t (
Var
io
Speed)Ÿ  Express Wash/ Speed Perfect/
(VarioSpeed) *
This function can reduce the running time  
by approx. 20% to 50% depending on the  
selected rinse programme. To obtain  
optimum cleaning and drying results at a 
reduced running time, water and energy  
consumption are increased.
Ï  Intensive zone *Inte
ns
iv
e
 z
on e
Perfect for a mixed load. You can wash  
very soiled pots and pans in the lower  
basket together with normally soiled 
utensils in the upper basket. The spray 
pressure in the lower basket is intensified, 
the rinsing temperature is increased 
slightly. 
·  Hygiene *Hyg
ie
ne
The temperature is increased during the  
cleaning process. This increases the 
hygiene status. This additional option is  
ideal for cleaning e.g. chopping boards  
and baby bottles.
Ha
lf lo
ad§  Half load *
If you have only a few items to wash (e.g.  
glasses, cups, plates), you can switch to  
“half load”. This will save water, energy  
and time. It is recommended to put a little 
less detergent in the detergent dispenser 
than for a full load.
¿ Extra drying *Ex
tr
a
 d
ry
in
g
An increased temperature during the final  
rinse and an extended drying phase  
ensure that even plastic parts dry better. 
There is a slight increase in the energy 
consumption.
Programme data
The programme data (consumption 
values) can be found in the summary 
of instructions. This data refers to normal 
conditions and the water hardness set  
value 2. Different influencing factors such  
as water temperature or mains pressure 
may result in deviations.
Aqua
 s ensorAqua sensor *
* depending on model 
The Aqua sensor is an optical measuring  
device (light barrier) which measures the  
turbidity of the rinsing water. 
The Aqua sensor is used according to the  
programme. If the Aqua sensor is active,  
“clean” rinsing water can be transferred to  
the next rinse bath and water consumption 
can be reduced by 3–6 litres. If the  
turbidity is greater, the water is drained  
and is replaced with fresh water. In the 
automatic programmes the temperature 
and running time can also be adjusted to  
the degree of soiling.
Switching on the appliance
– Turn on the tap fully. 
–Switch on ON/OFF  switch ( . 
The display of the last selected  
programme flashes. This programme 
remains selected unless another 
programme is selected with the button 
<  H  or button >  P.
– Press the START button  h. 
– Close the door. The programme starts running.
Additional optionsWashing the dishes
 
						

							en
17
T
im
er
 p
rogramm
in
gTimer programming *
* depending on model 
You can delay the start of the programme  
by 3, 6 or 9 hours. 
–Switch on ON/OF F switch ( .
– Keep pressing the Preselected starting  time button  0 until the appropriate 
display 3h, 6h or 9h is lit.
– Press START button  h, timer 
programming is activated.
– To delete the preselected starting time,  keep pressing the Preselected starting  
time button  0 until none of the 
displays 3h, 6h or 9h is lit. 
You can change your programme  
selection at any time until the 
programme starts.
End of programme
The programme has ended when the End  
display  ` is lit.
The end of the programme is also  
indicated by an acoustic signal. The 
buzzer volume can be set in 4 stages.  
Accordingly 0, 1, 2 or 3 displays are lit  
(see water hardness table). Factory 
setting: 2. This function can be changed 
as follows: 
– Open the door. 
–Switch on ON/OF F switch ( . 
– Hold down button >  P and press 
START button  h until the End display 
`  and salt refill indicator  )* flash.
– Release buttons. 
– Keep pressing button >  P until the 
salt refill indicator  )* and  rinse aid 
refill indicator  ) flash.
– Release buttons. The refill indicators  )* and  ) flash 
and the displays  # and  + are lit 
(= Setting 2). The set buzzer volume  
can be heard. To change the setting, 
– Press the button < 
H until the 
required setting has been selected.
– Press START button  h.
The displays go out. The selected  
setting is saved.
– Close the door. 
Note 
To save energy, the dishwasher  
automatically switches off after 2 minutes 
after the end of the programme.
Switching off the appliance
Short time after the end of the programme: 
– Open the door. 
– Switch off ON/OFF switch  (.
– Turn off the tap (not applicable if Aqua- Stop fitted).
– Remove the utensils when they have  cooled down.
ã=Warning
At the end of the programme please open  
the door fully and not partially when 
emptying the dishwasher. Any escaping  
water vapour could damage sensitive  
worktops.
Interrupting the programme
– Open the door. 
– Switch off ON/OFF switch  (.
The LEDs go out. The programme is  
saved.  
If the door was opened on an  
appliance which has a warm water  
connection or is heated, first leave the  
door ajar for several minutes and then 
close. Otherwise, expansion (pressure) 
may cause the appliance door to 
spring open or water to run out of the 
appliance.
– To continue the programme, switch on  the ON/OFF switch  ( again.
– Close the door.
 
						

							en
18
Term
in
a
tin
g
 th
e
 p
r
og r
am meTerminating the programme  
(Reset)
– Open the door.
– Press START button  h for approx. 
3sec. 
The Cleaning display  X goes out.
– Close the door.
The remaining programme sequence  
lasts approx. 1 minute more. (Buzzer  
sounds.)
– Open the door. 
– Switch off ON/OFF switch  (.
– Close the door.
Changing the programme
When the START button  h has been 
pressed, the programme cannot be  
changed. 
The only way a programme can be  
changed is by Cancel programme (Reset).
Intensive drying
The final rinse uses a higher temperature 
which improves the drying result. The 
running time may increase slightly. 
(Caution if utensils are delicate!) 
– Open the door. 
–Switch on ON/OF F switch ( . 
– Hold down button >  P and press 
START button  h until the End display 
`  and salt refill indicator  )* flash.
– Release buttons. 
– Keep pressing button >  P until the 
salt refill indicator  )* and  “Check 
water supply”  )2 flash.
– Release buttons. The displays  )* and  )2 flash.
To change the setting, 
– Press button <  H until the display 
#  is lit (Intensive drying on).
– Press START button  h.
The displays go out. The setting is  
saved.
– Close the door. A regular inspection and maintenance of  
your machine will help to prevent faults. 
This saves time and prevents problems.
Overall condition of the machine
– Check spray arm for grease and 
limescale deposits.
If you find such deposits: 
– Fill detergent dispenser with detergent.  Start the appliance without utensils in  
the programme with the highest rinsing  
temperature.
Clean the appliance with detergents/ 
appliance cleaners which are particularly  
suitable for use with dishwashers. 
– Regularly clean door seal with a damp  cloth.
Never use a steam cleaner to clean your  
dishwasher. The manufacturer is not liable 
for any consequential damage. 
Regularly wipe the front of the appliance  
and fascia with a damp cloth; water and a 
little washing up liquid are adequate. Do 
not use sponges with a rough surface or 
abrasive detergents, as these could  
scratch the surfaces. 
Stainless steel appliances: To prevent  
corrosion, avoid using sponge cloths or  
wash them out thoroughly several times  
before using for the first time.
ã=Warning
Never use other chlorinated household  
detergents! Health hazard!
Special salt and rinse aid
– Check the refill indicators  )* and 
) . If required, refill salt and/or rinse 
aid.
Maintenance and care
 
						

							en
19
Filters
The filters 1R keep large foreign objects 
in the rinsing water away from the pump.  
These foreign objects may occasionally 
block the filters. 
The filter system consists of a coarse filter,  
a flat fine filter and a microfilter. 
– After each washing cycle check the  filters for residue.
– Unscrew filter cylinder as illustrated  and take out filter system.
– Remove any residue and clean filters  under running water.
– Re-install filter system in reverse  sequence and ensure that the arrow  
marks are opposite each other after 
closing the filter system.
Spray arms
Limescale and contaminants in the rinsing 
water may block nozzles and bearings on 
the spray arms  1: and  1B.
– Check outlet nozzles on the spray arms  for blockages.
– Unscrew the upper spray arm  1:.
– Remove the lower spray arm  1B 
upwards.
– Clean spray arms under running water. 
– Re-engage or screw on spray arms.
 
 
						

							en
20
The majority of  faults which could occur in  
daily operation can be rectified by the 
user. This ensures that the appliance is  
quickly available for use again. The  
following overview will help you locating 
the causes and gives helpful advise to 
eliminate them. 
Note 
If the appliance stops during dishwashing  
or does not start for no obvious reason, 
first run the Abort programme function 
(Reset).  
(See chapter entitled “Dishwashing”)
ã=Warning
Don’t forget: Repairs may be carried out  
by technicians only. If a component has to 
be replaced, ensure that only original 
spare parts are used. Improper repairs or 
use of non-original spare parts may cause  
considerable damage and put the user at  
considerable risk.
Waste water pump
Large food remnants or foreign objects 
which were not captured by the filters may 
block the waste water pump. The rinsing 
water will then be above the filter.  
In this case: 
– First always disconnect the appliance  from the power supply.
– Take out top basket  1 and bottom 
basket  1b.
– Remove the filters  1R.
– Scoop out water, use a sponge if  required.
– Prise out the white pump cover  (as illustrated) using a spoon. Grip the  
cover on the crosspiece and lift 
diagonally inwards. Remove cover 
completely.
– Check impeller wheel and remove any  foreign objects.
– Place cover in the original position and  press down until it engages (click).
–Install fil ters.
– Re-insert baskets.Troubleshooting