Siemens Sf 64t355 Operating Instructions

							en11
Adjusting  
the height of the basket * 
* depending on model 
If required, the height of the upper utensils  
basket 
1 can be adjusted to provide 
more space for tall utensils  
either in the upper or lower basket. 
Appliance height 81 cm 
Select one of the two following procedures  
according to the design of the top basket 
for your appliance model: 
Top basket with side levers 
– Pull out the top basket  1 out. 
–To  lower the basket, press in the left 
and then the right  
lever on the outside of the basket. In  
doing so, hold the sides of the basket  
along the upper edge to prevent it from  
suddenly dropping. –To
raise the basket, hold 
the basket on the sides of the upper  
edge and lift it up.
– Before re-inserting the basket again,  ensure that it is at the same 
height on both sides. Otherwise, 
the appliance door cannot be closed 
and the upper spray arm will not be 
connected to the water circuit. 
Top basket with  upper and lower 
roller pairs 
– Pull out the top basket  1 out. 
– Remove the upper basket and re- attach it to the upper (stage 2) or lower  
(stage 1) rollers.
Top basket Bottom 
basket
Setting 1 max. ø 20 cm 28 cm 
Setting 2 max. ø 25 cm 23.5 cm
    
						

							en 
12
You can use tablets as well as powder  
or liquid detergents for dishwashers, but 
never use washing up liquid. The dosage  
can be individually adjusted with powder  
or a liquid detergent according 
to the degree of soiling. Tablets contain  
an adequately large amount of active  
ingredients for all cleaning tasks. Modern,  
pow erful detergents predominantly  
use a low-alkaline formulation with 
phosphate and enzymes. Phosphates  
bond the lime in the water. Enzymes break  
down starch and remove protein. 
Phosphate-free detergents are less  
frequent. These have a slightly weaker  
lime bonding capacity and require 
a higher dosage. To remove coloured  
stains (e.g. tea, tomato sauce), oxygen- 
based bleaching agents are usually used. 
Note 
To ensure a good washing result, always  
follow the instructions on the detergent  
packaging! 
If you have further questions,  
we recommend that you contact  
the detergent manufacturers’ helpline.
ã=
Warning
Read and observe the safety information  
and instructions for use on the packaging  
for cleaning and rinsing agents. Adding detergent 
– If the detergent dispenser 
9 is still 
closed, press the lock  1b to open 
the detergent dispenser. 
Pour detergent into the dry detergent  
dispenser 9. Dosage: see 
manufacturer’s instructions  
on the packaging.  
The graduated detergent  
dispenser 9 helps you add 
the correct amount of powder or liquid 
detergent. 
Usually 20 ml–25 ml are adequate  
for normal soiling. If using tablets, one 
tablet is adequate.
– Close cover on the detergent  dispenser. To do this, (1) push the  
dispenser cover shut and (2) press  
gently on the end until the catch 
engages audibly. 
If using tablets, please refer  
to the manufacturer’s packaging where 
to put the tablets (e.g. cutlery basket,  
detergent dispenser, etc.). Even  
if using tablets, ensure that 
the detergent dispenser cover  
is closed.
Detergent
 
						

							en13
Tip 
If the utensils are only lightly soiled,  
slightly less than the indicated amount  
of detergent is usually adequate.  
Suitable detergents and care products  
can be purchased online via our website  
or via customer service (see back page). 
Combination detergent 
Apart from conventional detergents (Solo),  
a number of products are offered with  
additional functions. These products 
contain not only the detergent but also  
rinse-aid and salt replacement substances  
(3in1) and, depending on the combination  
(4in1, 5in1, etc.), additional components  
such as glass protection or stainless steel  
cleaner. Combination detergents function  
only up to a specific degree of hardness 
(usually 26° Clarke). Over this limit salt  
and rinse-aid must be added.  
As soon as combined detergents  
areused, therinse programme isadjusted 
automatically to ensure the best possible  
rinsing and drying result. Notes 
– You will obtain optimum rinsing 
and drying results by using solo  
detergents and applying salt and rinse 
aid separately.
– If programmes are short, tablets  may not have full cleaning effect due to  
different dissolving properties  
and there may even be undissolved 
detergent residue. It is recommended  
to use washing powder for these  
programmes.
– The Intensive programme (on some  models) requires one tab only. When 
using washing powder, you can apply  
some of this cleaning agent to the 
inside of the appliance’s door.
– Even if the rinse-aid and/or salt refill  indicator is lit, the rinse programme will  
run correctly with combined  
detergents.
– If using detergents in a water-soluble  protective cover: Take hold of the  
cover with dry hands only and put  
the detergent into an absolutely  
dry detergent dispenser only, otherwise  
the detergent may stick.
– If you switch from combined  detergents to solo detergents, ensure 
that the water softening system  
and amount of rinse aid have been  
set to the correct value.
 
						

							en 
14
The max. possible number of programmes is illustrated 
in this overview. 
The corresponding programmes and their arrangement c an be found on the fascia.
Programme selection 
You can select a suitable programme  
according to the type of utensils and  
degree of soiling. 
Information for test institutes 
Test institutes can request the conditions  
for running comparison tests by sending  
an e-mail to  
[email protected].  
Quote the appliance number (E ­Nr.) 
and the production date (FD) which you  
can find on the rating  
plate 9*on the appliance door.
Overview of programmes
Type of utensils Type of soiling Programme Possible additional  optionsProgramme sequence
pots and pans,  non-sensitive  utensils 
and cutlery very adhesive burned-
in or dried-on food 
remnants containing 
starch or protein ²
Intensive 70°
allPrerinse
Clean 70°
Intermediate rinse Final rinse 70°
Dry
Ò
Auto 55°–65° Is optimised according 
to the soiling with the aid 
of sensors.
mixed utensils  and cutlery part dried, common 
household food  remnants â
Eco 50° Prerinse
Clean 50°
Intermediate rinse
Final rinse 65° Dry
sensitive utensils,  cutlery, 
temperature-
sensitive plastic  and glasses slightly adhesive, 
fresh food remnants ê
Gentle 40° Reduce Time
Half load Prerinse
Clean 40°
Intermediate rinse Final rinse 55° Dry
ò
Quick 45° noneClean 45°
Intermediate rinse Final rinse 55°
all types of utensils cold rinsing, 
intermediate cleaning ú
Prerinse none Prerinse
 
						

							en15
* depending on model 
Additional options can be set with the  
buttons 
H.
Ÿ  Express Wash/ Speed 
Perfect * 
The >>Express Wash/ Speed Perfect
						

							en 
16
Optical display while  
the programme is running * 
* depending on model 
While the programme is running, a light  
spot shines on the floor under  
the appliance door. Do not open  
the dishwasher door until the light point  
is no longer visible on the floor. 
If the appliance is installed at eye-level,  
with flush furniture front, the light point  
is not visible.  
Remaining running time display 
When the programme is selected, the  
remaining running time of the programme  
is indicated on the digital display 
@. 
The running time is determined during the  
programme by the water temperature, the  
number of utensils as well as the degree  
of soiling and may vary (depending on the 
selected programme).
Timer programming * 
* depending on model 
You can delay  
the start of the programme in 1 hour steps  
up to 19 hours. 
– Switch on the main switch  (.
– Press the timer programming  button 8 until the digital display @ 
jumps to ‚œ.
– Keep pressing the timer programming  button 8 until the required time 
is displayed.
– To delete the preselected starting time,  press the button 8 until ‹œ 
is indicated on the digital display @.
You can change your programme  
selection at any time until  
the programme starts. End of programme 
The programme has ended  
when the value
‹ 
is indicated on the numerical display @.
The end of the programme is also 
indicated by an acoustic signal. This  
function can be changed as follows: 
– Open the door. 
– Hold down programme button 3 
and switch on the main switch (. 
– Release both buttons.
The programme button 3 flashes 
and the factory-set value ƒ (half-loud) 
lights up on the numerical display @.
To change the setting:
– Press programme button 3. Each 
time the button is pressed, the set  
value increases by one level;  
when the value of „ has been reached, 
the display jumps back to ‹ (off).
– Switch off main switch (, the set 
value is saved.
– Close the door.
Switching off the appliance 
Short time after the end of the programme: 
– Open the door. 
– Switch off the main switch  (.
– Turn off the tap (not applicable if Aqua- Stop fitted).
– Remove the utensils when they have  cooled down.
 
						

							en17
ã= Warning
At the end of the programme please open  
the door fully and not partially  
when emptying the dishwasher. Any  
escaping water vapour could damage  
sensitive worktops. 
Interrupting the programme 
– Open the door. 
–Switchoffthemain switch  (.
TheLEDs go out. Theprogramme  
is saved.  
If the door was opened on an  
appliance which has a warm water  
connection or is heated, first leave 
the door ajar for several minutes  
and then close. Otherwise, expansion  
(pressure) may cause the appliance 
door to spring open or water to run  
out of the appliance.
– To continue the programme,  switch on the main switch ( again.
– Close the door. 
Terminating the programme  
(Reset) 
– Open the door. 
– Simultaneously press programme  buttons # and 3 
for approx. 3 sec.
– Close the door. The programme sequence lasts  
approx. 1 min. On the digital  
display @ ‹ is indicated.
– Open the door. 
–Switchoffthemain switch (.
– Close the door. Changing the programme 
After you have switched the appliance on,  
it is possible to change the programme  
within 2 min. 
If you want to change the programme  
afterwards, the appliance waits until  
the initiated programme section  
(e. g. washing) ends. The remaining time  
comprises the remaining time  
of the previous programme section  
and the remaining time of the new  
selected programme. 
Intensive drying 
The final rinse uses a higher temperature  
which improves the drying result. 
The running time may increase slightly.  
(Caution if utensils are delicate!) 
– Open the door. 
– Hold down programme button
# 
and press main switch ( 
until the digital display illuminates. 
– Release both buttons. The LED for button # flashes 
and the digital display @ displays 
the setting ‹  (off) or ‚ (on).
To change the setting: 
– By pressing the # button, you can 
switch intensive drying on ‚or off ‹.
– Switch off the main switch  (.
The set value is saved. 
– Close the door.
 
						

							en 
18
A regular inspection and maintenance of  
your machine will help to prevent faults. 
This saves time and prevents problems. 
Overall condition of the machine 
– Check spray arm for grease and 
limescale deposits.
If you find such deposits: 
– Fill detergent dispenser with detergent.  Start the appliance without utensils in  
the programme with the highest rinsing  
temperature.
Clean the appliance with detergents/ 
appliance cleaners which are particularly  
suitable for use with dishwashers. 
– Regularly clean door seal with a damp  cloth.
Never use a steam cleaner to clean your  
dishwasher. The manufacturer is not liable  
for any consequential damage. 
Regularly wipe the front of the appliance  
and fascia with a damp cloth; water and a  
little washing up liquid are adequate. Do  
not use sponges with a rough surface or 
abrasive detergents, as these could  
scratch the surfaces. 
Stainless steel appliances: To prevent  
corrosion, avoid using sponge cloths or 
wash them out thoroughly several times  
before using for the first time.
ã= Warning
Never use other chlorinated household  
detergents! Health hazard! 
Special salt and rinse aid 
– Check the refill indicators  X and 
` . If required, refill salt and/or rinse 
aid. Filters
The filters
1J keep large foreign 
objects in the rinsing water away from  
the pump. These foreign objects may 
occasionally block the filters. 
– After each wash cycle check the filters  for residue and clean if required.
– After unscrewing the coarse microfilter,  you can take out the filter group.
– Remove any residue and clean filters  under running water.
– Re-install filter system in reverse  sequence and ensure that the arrow  
marks are opposite each other after  
closing the filter system.
Maintenance and care

 
						

							en19
Spray arms 
Limescale and contaminants in the rinsing  
water may block nozzles  
and bearings on the spray arms 
12 
and 1:.
– Check outlet nozzles on the spray  arms for blockages.
– Unscrew the upper spray arm  12.
– Remove the lower spray arm  1: 
upwards.
– Clean spray arms under running water. 
– Re-engage or screw on spray arms. The majority of  faults which could occur in  
daily operation can be rectified by the  
user. This ensures that the appliance is 
quickly available for use again. The  
following overview will help you locating  
the causes and gives helpful advise to 
eliminate them. 
Note 
If the appliance stops during dishwashing  
or does not start for no obvious reason,  
first run the Abort programme function  
(Reset).  
(See chapter entitled “Dishwashing”)
ã=
Warning
Don’t forget: Repairs may be carried out  
by technicians only. If a component has to 
be replaced, ensure that only original  
spare parts are used. Improper repairs or  
use of non-original spare parts may cause 
considerable damage and put the user at  
considerable risk.
Troubleshooting
 
						

							en 
20
Waste water pump 
Large food remnants in the rinsing water  
not retained by the filters may block  
the waste water pump. The rinsing water 
is then not pumped out and covers  
the filter.  
In this case: 
– First disconnect the appliance from 
the power supply.
– Remove the filters  1J.
– Scoop out water, use a sponge if  required.
– Loosen screw on the cover (Torx T 20)  and remove the cover.
– Check inner compartment and remove  any foreign objects.
– Re-insert cover and screw tight. 
– Re-insert the filters and screw tight. 
... when the appliance is  
switched on 
The appliance does not start. 
– The mains fuse has tripped. 
– The appliance plug has not been  inserted.
– The appliance door has not been shut  properly. ... on the appliance 
Lower spray arm rotates sluggishly. 
– Spray arm blocked.
The door is difficult to open. *
– Child-proof lock is activated. 
The deactivation instructions  
areatthebackintheenvelope. 
* depending on model
Cover on the detergent dispenser cannot  
be closed. 
– Detergent dispenser overfilled or  mechanism blocked by sticky  
detergent residue.
Detergent residue in the detergent  
dispenser. 
– Dispenser was damp when filled.
“Check water supply” display P lights 
up. 
– Tap turned off. 
– Water supply interrupted. 
–Supply hose ki nked.
–Fi lterinthewater supply bl ocked.
– Switch off the appliance and pull  out the mains plug. 
–T urno ff t het ap. 
–Cl ean f il t eri nthes up pl y h ose . 
– Reconnect power supply. 
–T urno n thet ap.
–S wit c ho n th ea pplia nc e.