Siemens Sf 25m250 Instructions For Use

							en11
Cups
 and glasses
Upper  basket 
20
* not  included with all models
Pots  and pans
Lower  basket 
27
Cutlery Cutlery should be placed in the dishwasher always unsorted and with the eating surface pointing downwards. The spray jet is then better able to reach theindividual parts. To prevent injuries, place long, pointed
accessories and knives on the ‡tagŠre (some models) or on the knife shelf (available as an accessory). Folding  spikes *
*  on applicable models
T o improve stacking of pots and pans, the
spikes can be folded down.
Shelf   *
*   not on all models
Lean tall glasses and those with long stems against the shelf ± not against other items to be washed.
Place glasses, cups and small bowls on the additional cup rack. The additional cuprack can be swivelled in or out as required.
    
						

							en
12
Small
 accessories holder*
*  some models
Light-weight plastic accessories, e.g. cups, lids, etc. can be held securely in the small accessories holder .
Adjusting position of basket *
*  not on all models
The top basket can be inserted on either its upper or lower rollers, according to requirement. This enables more height to be gained for bigger dishes in either the top or bottom basket. Select one of the two following procedures according to the design of the top basket for your appliance model: Top
 basket with upper
and lower roller pairs
Pull  out the top basket.
Remove the top basket and re-attach it to the upper or lower rollers.
   
						

							en13
Top
 basket with side levers
(Rackmatic)
Pull  out the top basket.
To lower the basket, press in
succession the two levers on the left and right sides of the basket. Always take hold of the side of the basket on the upper edge, otherwise the basketwill not drop smoothly (and may damage the utensils).
T o raise the basket, take hold of the
basket on the upper edge and pull upwards.
Before you re-insert the basket, ensure that it is at the same height on bothsides. Otherwise, the appliance door cannot be closed and the upper spray arm will not connect to the water circuit. Baking
 sheet spray head *
*  some models
Y ou can clean large baking sheets or
grilles with the baking sheet spray head.T o do this, remove the top basket and
insert the spray head as illustrated in the diagram.
T o ensure that the spray jet can reach all
parts, arrange the baking sheets as illustrated (max. 2 baking sheets and 2 grilles).
     
						

							en
14 Detergents
Information  about detergents
You  can use any brand of liquid or powder
detergent, as well as tablets, that have been specifically designed for use in domestic dishwashers. (Do not use normal washing-up liquid!) Nowadays there are three types of dishwasher detergent available:1.  those containing phosphates and      chlorine, 2.  those containing phosphates but no      chlorine, 3.  those containing neither phosphates     nor chlorine. When a phosphate-free detergent is used in conjunction with hard water , there is a
greater possibility that white marks will be left behind on crockery and glasses, etc. These can be avoided by pouring an increased amount of detergent into the 
dispenser. Chlorine-free detergents have a reduced bleaching ef fect. This can mean that tea
stains are not completely removed or plastic items become discoloured. This can be resolved by:
selecting a higher temperature programme, or
  increasing the amount of detergent,or
 using a detergent that contains chlorine.
Check the label on the detergentpackaging to determine whether a particular product is suitable for use with silverware. If you have any further questions, we recommend that you contact the customer advice departments of the various detergent manufacturers. Detergent
 compartment with
measuring marks The  side of the detergent compartment is
marked with lines to help you determine how much powder to add. The capacity of the detergent container is15 ml up to the bottom line and 25 ml up to the middle line. When the compartment is full it contains 40 ml.
If the detergent dispenser 30  is still
closed, press the lock 
28  to open the
detergent dispenser .
Adding  detergent
Fill the dispenser 30  with detergent.
Please observe the manufacturer s
instructions printed on the detergent packaging when determining the correct dosage.
Important
Due to the dif ferent solvency properties of
the detergent tablets supplied by various manufacturers, the cleaning ef ficiency of
the detergent may not be fully utilised by short programmes. It is recommended to use washing powder for these programmes.
If using the ªIntensiveº programme (some models), also pour approx. 10±15 ml of detergent ontothe appliance door . If using tablets,
also place a tablet on the appliance
door.
  
						

							en15
 Reduce costs!
If your dishes are only moderately dirty ,
you may be able to use less detergent than recommended.
Close the lid on the detergent compartment. Press down the lid (1) until it clicksshut (2).
If you are using detergent in tablet form, read the manufacturer s
recommendations on the packaging inorder to determine where the tablets should be placed inside the dishwasher (e.g. in cutlery basket, detergent compartment,etc.). Make sure that the lid on the detergent compartment is closed, even if you are using tablets. auto
 3in1
The  use of so-called combined detergent
products may make the use of rinse aid and/or salt unnecessary .
There are currently several types ofcombined detergent products available.
3in1:  They contain detergent, rinse aid
and  salt function.
2in1:  They contain detergent and rinse
aid  or salt function.
>>>  Always check the type of detergent
or combined product which you are using!
Always follow the operating instructionsor the information on the packaging.
The rinse programme is automaticallyadjusted in order to obtain the best possible rinsing and drying result. Observe the following important information if using combined cleaningproducts:
Regeneration salt is not required up to a water hardness of 21  dH (37  fH,
26  Clarke, 3.7 mmol/l) only . No other
settings on the appliance are required.
Salt is still required if the water hardness is  above 21 dH (37  fH,
26 Clarke, 3.7 mmol/l). Fill the salt
dispenser with salt 
24 and select
setting 6 on the water softening system.
If in doubt, please contact the detergent manufacturer , especially if:
the utensils are very wet at the end ofthe programme.
limescale forms.
   
						

							en
16
Note
Optimum rinsing and drying results can be obtained by using standard detergents in conjunction with separate application ofsalt and rinse aid. Observance of the operating instructions or information on the packaging of the combined detergents determines their
effectiveness.
Note
Even if the rinse aid and/or salt refill indicator is lit, the rinse programme runscorrectly when 3in1 products are used. If the rinse aid refill indicator 
7 or salt
refill 
6 indicator is defective and you
would like to switch it of f, proceed as
follows: Switching  the rinse-aid refill
indicator off or on* *  some  models
Y ou can switch of f the rinse-aid refill
indicator 
7 if you use a detergent
with integrated rinse-aid.
Close the door .
Press and hold down button A.
Press main switch 1 until the digital
display lights up.
Release both buttons. The digital display 
8 indicates 
(rinse-aid refill indicator) and the button
A  flashes.
By pressing button A you can switch
the rinse-aid indicator of f 
 or on .
Switch off the main switch 1;
The setting is saved. ªRemember to switch on the rinse-aid refill indicator again if you use a detergentwithout an integrated rinse-aid!º Switching
 the salt refill
indicator / water softening system off and on
Close  the door
Rotate the programme selector 3
from the 12 oclock position by one notch to the left.
Switch on main switch 1 and hold
down for at least 3 sec. The digital display 
8 indicates the
current set hardness value and the salt refill indicator 
6 flashes 
(hardness value has been set to 4 at the factory).
T o change the setting: Rotate the
programme selector 
3. 
Y ou can select a set value between
0 and 7 according to the hardness of your water .
Switch off the main switch 1. 
The chosen setting has now been stored.
Note
If you use the detergent and rinse aid separately or switch from combined detergents to standard cleaning products,ensure that the rinse aid refill indicator has been switched on and the water softening system has been set to the correct water hardness.
    
						

							en17
Overview
 of programmes
The  max. possible number of programmes is illustrated in this overview . 
The corresponding programmes for your appliance can be found on the fascia.
Cof fee, cake, milk,
sausage, cold drinks, salads
Soups, souf
fl‡s,
potatoes, pastries, rice, eggs,fried food Delicate
T
ype of Dishes
e.g. porcelain, pans, 
cutlery,glasses, etc.
T ype of food
remnants e.g. Programme- sequence
Dry
Clean 55 
Clean
40 
PrerinseClean
55 
Clean
45 
Soups,
potatoes, pastries,
rice, eggs, fried food
Wash programme V
ery little
Amount offood remnants State of food remnantIntensive
70Eco
50  Gentle
40  Quick
45  Prerinse
Mixed
Dry
Clean
65 
Clean
50 
Prerinse
Dry
Clean
70 
Inter-
mediate
rinse
Clean
70 
Prerinse
50 
Prerinse
Rinse of f if
the dishes
have been stacked
for several days in the
dishwash
er prior to washing.
Inter-
mediate
rinse
Inter-
mediate
rinse Inter-
mediate
rinse Inter-
mediate
rinse Inter-
mediate
rinse
Little
Large Mixed
Non-
sensitive
Lightly Adhesive
V ery adhesive
Dry
Clean
70 
Inter-
mediate
rinse
Clean
65 
Prerinse
Inter-
mediate
rinse
Normal
65 
Programme  selection
The  most appropriate programme can be
identified by comparing the type of crockery , cutlery, etc., as well as the amount and condition of food remains,with the details contained in the programme overview
.
Y ou will find the appropriate programme
information in the introduction.
    
						

							en
18 Washing
 dishes
 Reduce costs!
If only a small number of dishes have been loaded into the dishwasher , selecting
a programme that operates at the next lowest temperature will usually suf fice.
Programme  specifications
The  programme specifications can be
found in the summary of instructions.Programme specifications refer to normal conditions. Greater deviations may occur due to:
varying amounts of dishes
water supply temperature
water pipe pressure
ambient temperature
mains voltage tolerances
and the tolerances specific to the appliance (e.g. temperature, amount of water , etc.)
The water consumption values refer to a set water hardness value of 4. Aqua  sensor *
*  on applicable models
The Aqua sensor is an optical measuring device which measures the turbidity of the rinsing water . A light barrier can detect
dissolved food remnants in the water , e.g.
egg, fat and oats. The Aqua sensor is used according to the programme. When the Aqua sensor is active, ºcleanº rinsing water may be transferred into the next rinsing bath and/or the temperature adjusted. If theturbidity is greater , the water is drained
and is replaced with fresh water . In this
way the water consumption is reduced by approx. 4 litres for utensils which are ºlessº 
dirty. Switching
 on the appliance
Close the door .
Turn on the tap fully .
Rotate programme selector 3 to the
required programme.
Switch on the main switch 1.
The expected programme duration is indicated on the numerical display 
8.
The programme sequence starts 
automatically.
Remaining  running time display
When  the appliance has started, the
expected programme running time is displayed. The programmed running time is af fected by the water temperature, the
number of dishes, as well as the degree of soiling. If these conditions are changed, the running time (depending on the selected programme) can vary greatly .
As the ef fect is not detected until a
programme is running, the time maybe longer or shorter than expected. End  of programme
The  programme has ended when a figure
 appears in the numerical display 8.
Switching  the dishwasher OFF
Several  minutes after the programme has
ended:
Set the main switch 1 to OFF .
Turn the water tap of f.
(Does not apply when Aqua-Stop unit has been fitted)
Remove dishes, etc. when they have cooled down.
   
						

							en19
Interrupting
 the programme
Set main switch 1 to OFF .
Indicator lights extinguish. The programme is retained in the dishwasher memory .
If the hot water was switched ON or the appliance has already heated up and then the appliance door opened, leave the door ajar for several minutes and then close. Otherwise, the appliance door may fly open due to expansion.
In order to continue with the stored programme, set the main switch to ONagain.
Terminating  the programme
(Reset)
Only  when the main switch is on:
Rotate programme selector to the Reset position. The digital display indicates 
 after approx. 3 sec.
The programme sequence lasts approx. 1 min.
When the programme has run, switch of f the main switch 
1.
T o restart, rotate the programme selector
3 to the required programme. Switch on
the main switch 
1. The programme
sequence starts automatically .
Changing  the programme
It  is possible to change the programme
within 2 minutes after you have switched the dishwasher on. Should it be necessary to change the programme after this period, the programme cycle that has already been begun (e.g. washing) will be completedfirst of all. The new remaining time displayed is the sum of the remaining time from the preceding programme cycle and the remaining time attributable to the new programme that has been selected. Intensive
 drying
By  activating the ªIntensive dryingº
function, the final rinse will producea higher temperature in all programmes resulting in an improved drying result(please note that higher temperatures might have an ef fect on delicate items).
Close the door.
Hold down button B and
switch on main switch 
1.
Release both buttons. The digital display 
8 indicates 
(on) or  (of f) and button B flashes.
To change the setting, press
button 
B .
Switch of f the main switch 1; the
chosen setting has now been stored.
    
						

							en
20 Additional
 functions
 Pre-Soak *
The  Pre-Soak programme option serves to
perform a pre-soak cycle before the main programme. This cycle enables cookware, e.g. pans, bowls, etc. to be pre-soakedand pre-rinsed in the lower rack. If youwish to pre-soak the dishes, thisprogramme option must be selected bypressing the ªPre-Soakº button before theprogramme starts. The recommendeddetergent amount is approx. 5 g pouredonto the inside of the door .
 Time reduction/ time saving *
Pressing  the ªTime reduction/time savingº
button provides a short wash cycle by curtailing the drying phase and thewashing time. The washing and dryingperformance will be reduced with the T ime
reduction/time saving programme option.
 Half load*
If  you have only a few items to wash (e.g.
glasses, cups, plates), you can switch to ªHalf loadº. The ªhalf loadº additionalfunction saves water , energy and time. It is
recommended to put a little less detergent in the detergent dispenser than for a full load.
h.
 T ime delay *
You  can delay the start of the programme
in 1-hour steps up to 19 hours.
Switch on the appliance.
Press the timer programming button until the digital display 8 jumps to
.
Keep pressing the timer programming button until the required time is displayed.
T o delete the timer programming,
keep pressing the button until 
is displayed. Y ou can change your programme
selection at any time until the programme starts.
*  on  some models additional functions
4 can be set with the buttons. Maintenance
 and care
A  regular inspection and maintenance
of your machine will help to prevent faults. This saves time and prevents problems. Therefore you should occasionally have a careful look inside your dishwasher .
Overall  condition
of the machine
Check  spray arm for grease and
limescale deposits.
If you find such deposits:
Fill the detergent dispenser with detergent, start the appliance without utensils in the programme which hasthe highest wash temperature.
Clean the appliance with detergents/appliance cleaners which are particularly suitable for use with dishwashers.
Regularly wipe the door seal with a damp cloth to remove deposits.
Never use a steam cleaner to clean your dishwasher . The manufacturer is not liable
for any consequential damage. Regularly wipe the front of the appliance and panel with a damp cloth; water and a little washing-up liquid will suf fice.
Do not use sponges with a rough surfaceor abrasive detergents, as these couldscratch the surfaces.
Attention!
Never use other chlorinated household detergents! Health hazard! Special  dishwasher salt
Check the LOW SAL T indicator 6.
T op up with salt, if required.
Rinse-aid
As soon as the rinse-aid refill indicator lights up on the control panel 
7,
refill with rinse aid.