Siemens Se 65e330 Instructions For Use

							en21
The filter on the water supply hose is blocked.Switch of f the appliance and pull
out the mains plug. T urn off the
tap. Then clean the filter which issituated at the connection of the supply hose. Finally , restore the
power , turn on the tap and switch
on the appliance.
...  with the appliance itself
Lower  spray arm rotates with
difficulty
Spray arm is blocked by small items or food remains.
Lid in detergent compartment cannot be closed
Detergent compartment has been overfilled.
Mechanism is clogged with remnants of detergent. Indicator lamps do not extinguish after washing has finished.
Indicator lights flash after the programme has started.
No programme selected.
 Indicator lamps do not extinguish after washing has finished
Main switch is still set to ON.
Remnants of detergent stuck inside dispenser
Compartment was damp when it was filled up with detergent. Compartment must be dry before detergent is added.
ªCheck water supplyº 7 display
lights up
T ap turned of f or calcified.
Water supply interrupted.
Filter in the water supply blocked.
Supply hose kinked.
The waste water pump is blocked.
Water is left in the appliance
at the end of the programme.
The waste water hose is blocked or kinked.
The waste water pump is blocked.
The filters are blocked.
The programme has not yet ended. W ait until programme
ends (digital display indicates 0) or implement the ªResetº function.
...  during washing
Unusual  amount of foam is created
Normal washing up liquid has been poured into the rinse-aid 
container.
Remove any spilled rinse aid with a cloth as it could otherwise leadto excessive foaming during the next washing cycle.
Appliance stops suddenly while washing is taking place
Cut in electricity supply to appliance.
Water supply has been
interrupted.
Implement the ªRESETº function.
Knocking sound can be heard while washing is taking place
A spray arm is knocking against the dishes inside the appliance.
Rattling sound can be heard while washing is taking place
Crockery has not been stacked properly inside the appliance.
 
						

							en
22
Knocking sound coming from inlet valves
This is caused by the way the water pipes have been laid and it has no ef fect upon the way the
appliance functions. There is no remedy for this.
...  with the dishes, cutlery , etc.
Remnants of food are stuck to the
dishes, cutlery , etc.
Dishwasher was not loaded properly. Jets of water could not
reach all parts of the dishes, etc.
T oo many items in the rack.
Items in the rack were touching each other .
Not enough detergent was added to dispenser .
Selected wash programme was not intensive enough.
Rotation of spray arm was obstructed by dish, etc.
Nozzles in spray arm are blocked by remnants of food.
Filters are blocked.
Filters have been incorrectly fitted.
Waste-water pump is jammed.
Plastic items are discoloured
Not enough detergent was added to dispenser .
White stains are left on crockery ,
glasses have a milky appearance
Not enough detergent was added to input compartment.
Amount of rinse-aid was set too 
low.
Although water is quite hard, no salt has been put in appliance.
W ater softener was set too low .
Lid on salt container is not screwed tight.
If you used a phosphate-free detergent, try a detergentcontaining phosphates and compare results.
Dishes, cutlery, etc. have not been
dried
Selected programme did not include drying function.
Amount of rinse-aid was set too 
low.
Items were removed from dishwasher too soon.
Glasses have a dull appearance
Amount of rinse-aid was set too 
low.
T ea stains or traces of lipstick have
not been completely removed
Detergent does not have a suf ficient bleaching ef fect.
Washing temperature was set too
low.
T races of rust on cutlery
Cutlery is not suf ficiently rustproof.
Salt content in washing water is too high.
Lid on salt container is not screwed tight.
Too much salt was spilt while
filling container .
Glasses become clouded and discoloured; coating cannot be wiped off
Unsuitable detergent was used.
Glasses are not dishwasher-proof.
Smears left behind on glasses and cutlery; glasses have acquired ametallic appearance
Amount of rinse-aid set too high.
 
						

							en23
Customer
 Service
Please  call your local service agent, if you
are not able to resolve any problem yourself. The name of your nearest service agent is shown in the Customer Service address list. When you call, please provide details of the model number (1) and the production (FD) number (2) which are shown on the nameplate 
33 on the
appliance door .
FD
1 2
Warning Please note that a visit by the customer service technician in the event of a fault or one ofthe problems previously discussed is not free of charge
even during the warranty
period.
Information
Notes  on comparison tests
You  will find details of the conditions for
the comparison tests on the additional ºNotes on comparison testsº sheet. The consumption values for the relevant programmes are given in the introduction. General
Built-under and integrated appliances which are subsequently installed as free-standing appliances must be secured to prevent them from falling over , e.g. by screwing them to the wall
or by installing them under a continuous worktop which is screwed to the adjoining units.
For Swiss version only: The appliance can be installed without dif ficulty between wooden and plastic
walls in a kitchen range. If the applianceis not connected via a plug, theinstallation side must feature an all-pole disconnector with a contact gap of at least 3 mm in order to satisfy therelevant safety regulations.
 
						

							en
24 Installation
The dishwasher must be connected by a qualified technician to ensure correctoperation. The specifications for supply ,
drainage and connected load must fulfilthe required criteria as stated in the following paragraphs or in the installation instructions. Install the appliance in the following sequence: ± Check the delivery ± Install the appliance ± Connect the waste water ± Connect the fresh water± Connect the power supply Delivery Y our dishwasher was checked at the
factory to ensure that it was in perfect working order . This may have left some
small water stains in the dishwasher .
These will disappear after the first rinse cycle. Installation The required installation dimensions can be found in the installation instructions. Level the appliance with the aid of the height-adjustable feet. Ensure that the appliance is situated securely on the floor .
If the appliance is installed under a worktop, tension the appliance only lightly against the worktop with the height-adjustable feet. 
Waste  water connection
See  the installation instructions for the
required connection steps. If required, attach a siphon with drainage spigot.Using the enclosed parts, connect the waste water hose to the drainage spigot of the siphon. Ensure that the drainage hose is not kinked, crushed or twisted (ensure thatthere is no sealing cover which prevents the waster water from flowing away!). Fresh
 water connection
Using  the enclosed parts, connect the
fresh water connection to the tapaccording to the installation instructions. Ensure that the fresh water connection isnot kinked, crushed or twisted. When replacing the appliance, always connect a new water supply hose to the water supply . The old supply hose must
not be re-used. W ater pressure:
Minimum 0,05 MPa (0,5 bar) ± maximum 1 MPa (10 bar). If the water pressure is higher , install a
pressure reducing valve. Flow rate:Minimum of 10 litres per minute.W ater temperature:
W e recommend that you use cold water .
If you do use hot water , the temperature
should not exceed 60  5C.
Electrical  connection
Connect  the appliance only to 230 V
alternating current via a correctly installed socket with protective conductor .
See rating plate for required fusing 
33 . 
The socket must be attached near the dishwasher and be freely accessible. The connection may be modified by an electrician only .
Use only a residual-current-operated circuit-breaker which features the 
symbol. Only this circuit breaker guarantees compliance with the currentlyvalid regulations.
 
						

							en25
Removing
 the appliance
It  is essential, when removing the
appliance, to observe the following sequence: First, disconnect the appliance from the power supply .
Pull out the mains plug. T urn of f the water supply .
Disconnect the waste water and freshwater connections. Loosen the fastening screws under theworktop. If fitted, remove the base panel. Pull out the appliance, carefully pulling the hose behind. 
Transporting  the dishwasher
Drain  water from the dishwasher . Secure
all loose parts. The appliance should only be transported in an upright position.
If the appliance is not kept upright during transport, any water left inside may seep into the control module andcause subsequent errors with programme functions.
Protection  from freezing
temperatures If  the appliance is installed in a location
where there is a risk of freezing temperatures (e.g. in a holiday home), all water must be completely drained out of the interior (see ªT ransporting the
dishwasherº). T urn OFF the tap, disconnect the supply
hose and allow to drain. Waste
 disposal
Disposal Old  appliances are not worthless rubbish.
V aluable raw materials can be reclaimed
by recycling old appliances. Pull out the mains plug of the redundant appliance. Cut of f the power cord and
discard with mains plug.T o prevent children from locking
themselves in the appliance andsuf focating, destroy the door lock
and childproof lock (if fitted). Y ou received your new appliance in
a protective shipping carton. All packaging materials are environmentally friendly and recyclable. Please contribute to a better environmentby disposing of packaging materials in an environmentally-friendly manner . All plastic
parts of the appliance are identified byinternationally standardised symbols (e.g. >PS< polystyrene).When the appliance is being disposed of, the plastic waste can be sorted for environmentally-friendly recycling. Please ask your dealer or inquire at your local authority about current means of disposal.
 
						

							en
26
Disposal
 of the packaging
Please dispose of the packaging
material in an environmentally friendly manner .
Keep children away from shipping carton and packaging components. Danger of suf focation from folding
cartons and plastic film.
 Corrugated cardboard consists mainly of wastepaper .
 The moulded polystyrene parts donot contain anychlorofluorohydrocarbons.
 The polyethylene film (PE) consistspartly of secondary raw materials.
 The wooden frames (if fitted) aremade of untreated residual wood.
 The hoops (if fitted) consistof polypropylene (PP).
Disposal  of redundant
appliances
Make  redundant appliances unusable
to prevent subsequent accidents.
Dispose of the appliance in an environmentally friendly manner .
Warning
Children could become locked in the appliance (risk of suf focation) or find
themselves in other dangerous situations. Therefore: Pull out the mains plug, sever and dispose of the power cord. Destroy the door lock so that the door can no longer be closed.
This appliance is labelled in accordance with European Directive 2002/96/EG concerning used electrical and electronic appliances (waste electrical and electronic equipment ± WEEE). The guidelinedetermines the framework for the return and recycling of used appliances as applicable throughout the EU.
  
						

							Large sheets or grilles and plates which have a diameter greater than 30 cm (gourmet
plates, pasta plates, dinner plates) can be cleaned with the aid of the spray head. T o do this, remove the top basket and insert the spray head as illustrated in the diagram.
T o ensure that the spray jet can reach all parts, arrange the baking sheets as illustrated
(max. 4 baking sheets and 2 grilles). Never operate the dishwasher without the top basket or baking sheet spray head!
Baking
 sheet spray head *
* some models
   
						

							           
AQUA-ST
OP guarantee
(does not apply to appliances without Aqua-Stop) In addition to warranty claims against the seller based on the purchase contract and in addition to our appliance warranty we will pay damages under the following conditions: 1.  If our Aqua-Stop system is defective and causes water damage, we will make good the damage for private users.
2.  This liability guarantee is valid for the service life of the appliance.
3.  A prerequisite for the warranty claim is that the appliancehas been correctly installed and connected with Aqua-Stop according to our instructions.  ªThis also includes the correct installation of the Aqua-Stop extension (original accessory).º Our warranty does not extend to defective feed lines or fittings up to the Aqua-Stop connection on the tap.
4.  If your appliance is fitted with Aqua-Stop, you can leave your appliance unattended during operation and leave the tapturned on afterwards. The tap should only be turned of f if you
are absent from home for a prolonged period, e.g. severalweeks holiday .
Siemens-Electroger‚te GmbHCarl-W ery-Straûe 34, 81739 M˜nchen
To  contact  us directly , use the tel. no or fax no. in the
enclosed  customer service list.
www.siemens-homeappliances.com