Siemens Se 64m359 Instructions For Use

							en11
Pots
 and pans
Lower  basket 
27
Cutlery Cutlery should be placed in the dishwasher always unsorted and with theeating surface pointing downwards. The spray jet is then better able to reach the individual parts. To prevent injuries, place long, pointed
accessories and knives on the étagère (some models) or on the knife shelf (available as an accessory). Folding  spikes *
*  on applicable models
T o improve stacking of pots and pans, the
spikes can be folded down.
Shelf   *
*   not on all models
Lean tall glasses and those with long stems against the shelf – not against other items to be washed.
Long items, serving cutlery , salad servers
or knives should be placed on the shelf so that they do not obstruct the rotation of the spray arms. The shelf can be folded back when not required for use. Small  accessories holder*
*  some models
Light-weight plastic accessories, e.g. cups, lids, etc. can be held securely in the small 
accessories holder.
    
						

							en
12
Adjusting
 the height
of the basket * * some  models
If required, the height of the upper utensils basket can be adjusted to provide more space for tall utensils either in the upper or lower basket.
Appliance height in cm
8186
Max. ø  in cm upper20/25*20/25*
max. ø  in cm lower30/25*34/29*
Select one of the two following procedures according to the design of the top basket for your appliance model: 
Top  basket with upper and
lower roller pairs
Pull  out the top basket.
Remove the top basket and re-attach it to the upper or lower rollers.
Top  basket with side levers
(Rackmatic)
Pull  out the top basket.
To lower  the basket, press in one lever
and then the other situated on the left and right of the basket exterior , holding
the basket firmly on the sides of theupper edge to prevent it from fallingdown.
To  raise  the basket, hold the basket on
the sides of the upper edge and lift it up.
Before re-inserting the basket again, ensure that it is at the same height on both sides. Otherwise, the appliancedoor cannot be closed and the upper spray arm will not be connected to the water circuit.
   
						

							en13
Detergent
Y ou can use commercially available liquid
or powder proprietary detergents for dishwashers or T ABS (do not use
handwash!). If phosphate-free detergents are used with hard tap water , white deposits may be
deposited more easily on utensils and the container walls. This can be remedied by adding more detergent. See detergent packaging to determine whether a detergent is suitable for silver parts. If you have any other questions, we recommend that you contact the helplinesof the detergent manufacturers. Detergent  dispenser with
dosing aid The  graduated detergent dispenser helps
you pour in the correct amount. Lower line: 15 ml
Middle line: 25 ml
Full to the brim: 40 ml
If the detergent dispenser 
30  is still
closed, press the lock 
28  to open the
detergent dispenser .
Adding  detergent
Fill the dispenser 30  with detergent.
Dosage: see manufacturer ’s
instructions on the detergent packaging.
Note
The cleaning tabs from various manufacturers exhibit dif fering dissolving
properties, so washing power may notdevelop fully during short programmes and there may be undissolved cleaning agent residue. It is recommended to usewashing powder for these programmes. The Intensive programme (on some models) requires one tab only . When using
washing powder , you can apply some
of this cleaning agent to the inside ofthe appliance’ s door.
 Reduce costs!
If your dishes are only moderately dirty ,
you may be able to use less detergent than recommended.
Close the lid on the detergent compartment. Press down the lid (1) until it clicksshut (2).
If you are using detergent in tablet form, read the manufacturer ’s
recommendations on the packaging inorder to  determine where the tablets should be placed inside the dishwasher (e.g. in cutlery basket, detergent compartment, etc.). Make sure that the lid on the detergent compartment is closed, even if you are using tablets.
   
						

							en
14 auto
 3in1
The  use of so-called combined detergent
products may make the use of rinse aid and/or salt unnecessary .
There are currently several types ofcombined detergent products available.
2in1:  They contain detergent and rinse
aid  or salt function.
3in1:  They contain detergent, rinse aid
and  salt function.
4in1 : They contain a detergent,
rinse-aid, salt function  and an additional
glass protection component.
In addition, other combined products with a comparable ef fect are offered according
to the manufacturer .
>>>  Always check the type of detergent
or combined product which you are using!
Always follow the operating instructionsor the information on the packaging.
The rinse programme is automaticallyadjusted in order to obtain the best possible rinsing and drying result. Observe the following important information if using combined cleaning products:
Regeneration salt is not required up to a water hardness of 21  dH (37  fH,
26  Clarke, 3.7 mmol/l) only . No other
settings on the appliance are required.
Salt is still required if the water hardness is  above 21 dH (37  fH,
26 Clarke, 3.7 mmol/l). Fill the salt
dispenser with salt 
24 and select
setting 6 on the water softening system.
If in doubt, please contact the detergent manufacturer , especially if:
the utensils are very wet at the end ofthe programme.
limescale forms.
Note
Optimum rinsing and drying results can be obtained by using standard detergents in conjunction with separate application ofsalt and rinse aid. Observance of the operating instructions or information on the packaging of the combined detergents determines their 
effectiveness.
Note
Even if the rinse aid and/or salt refill indicator is lit, the rinse programme runscorrectly when 3in1 products are used. If the rinse aid refill indicator 
8 or salt
refill 
7 indicator is defective and you
would like to switch it of f, proceed as
follows: Switching  the rinse aid refill
indicator off and on 
You  can switch the rinse aid refill indicator
8 on or of f. This function can be
changed as follows.
Hold down the programme button 3
and press the main switch 1 until the
digital display lights up, then release the buttons.
4 is indicated on the digital display
 (rinse aid refill indicator on).
By pressing the programme button
3, you can switch of f  or switch
on 
 the rinse aid indicator .
Switch off the main switch 1;
the setting is saved.
    
						

							en15
Switching
 the salt refill
indicator / water softening system off and on
Hold  down the programme button B
and switch on the main switch 
1,
then release the buttons. The illuminated button 
B  and the
factory-set value 
 on the digital
display flash. T o change the setting: press the
programme button 
B  .
Each time the button is pressed, the set value increases by one; when the value
 is reached, the display jumps back
to 
 (the salt refill indicator / water
softening system has been switched 
off).
Switch of f the main switch 1.
The set value is stored within the
device.
Approx. 4 litres of water are required to regenerate the water softening system.As a result, the water consumption per
rinse cycle increases by 0 to maximum4 litres depending on the water hardness
setting.
Note
If you use the detergent and rinse aid separately or switch from combined detergents to standard cleaning products, ensure that the rinse aid refill indicator hasbeen switched on and the water softening system has been set to the correct water hardness.
    
						

							en
16 Overview
 of programmes
The max. possible number of programmes is illustrated in this overview . 
The corresponding programmes for your appliance can be found on the fascia.
Cof fee, cake, milk,
sausage, cold drinks, salads
Soups, souf
flés,
potatoes, pastries, rice, eggs,fried food Delicate
T
ype of Dishes
e.g. porcelain, pans, 
cutlery,glasses, etc.
T ype of food
remnants e.g. Programme- sequence
Dry
Clean 55 
Clean
40 
PrerinseClean
55 
Clean
45 
Soups,
potatoes, pastries,
rice, eggs, fried food
Wash programme V
ery little
Little
Large
Amount offood remnants State of food remnantIntensive
70Eco
50  Gentle
40  Quick
45  Prerinse
MixedMixed
Non-sensitive
Medium Lightly Adhesive
Very
adhesive
Dry
Clean 65 
Clean
50 
Prerinse
Dry
Clean
70 
Dry
Clean
70 
Prerinse
40 
The programme sequence is
optimised and adjusted according to the degree of soiling on the utensils.
Auto
55 -65 
Prerinse
Rinse of f if
the dishes
have been stacked
for several days in the
dishwash
er prior to washing.
Inter-
mediate
rinse Inter-
mediate
rinse Inter-
mediate
rinse Inter-
mediate
rinse
       
						

							en17
Programme
 selection
The  most appropriate programme can be
identified by comparing the type of crockery , cutlery, etc., as well as the
amount and condition of food remains, with the details contained in the programme overview .
Y ou will find the appropriate programme
information in the introduction. Washing
 dishes
 Reduce costs!
If only a small number of dishes have been loaded into the dishwasher , selecting
a programme that operates at the next lowest temperature will usually suf fice.
Programme  data
The  programme specifications can be
found in the summary of instructions.Programme specifications refer to normal conditions. Greater deviations may occur due to:
dif ferent amounts of dishes
temperature of mains water supply
pressure of mains water supply
ambient temperature
fluctuations in mains voltage
machine-related factors (e.g. temperature, water volume, ...).
Energy and water consumption is reducedby up to 1/4 when dishes are washed in the upper basket only .
W ater consumption values are based on a
water hardness setting of 4. Aqua  sensor *
* some  models
The Aquasensor is an optical measuring device (light barrier) which measures the turbidity of the rinsing water .
The Aqua sensor is used according to the programme. When the Aqua sensor is active, “clean” rinsing water may be transferred into the next rinsing bath and/or the temperature adjusted. If the turbidity is greater , the water is drained
and is replaced with fresh water . In this
way water consumption can be reducedby approx. 4 litres.
  
						

							en
18
Switching
 the dishwasher ON
Turn on the tap.
Set main switch 1 to ON.
Indicators light up according to the last programme that was selected. This same programme will run again if no other programme button 
9 is
pressed
The numerical display 4 shows the
expected duration of the programme.
Close door .
The programme starts automatically .
Remaining  running time display
When  the appliance has started, the
expected programme running time is displayed. The programmed running time is af fected by the water temperature, the
number of dishes, as well as the degree of soiling. If these conditions are changed, the running time (depending on the selected programme) can vary greatly .
As the ef fect is not detected until a
programme is running, the time may be longer or shorter than expected. 
Time  delay *
*  on  applicable models
Y ou can delay the start of the programme
in 1-hour steps up to 19 hours.
Switch on the appliance.
Press the timer programming button
3 until the digital display 4 jumps
to 
.
Keep pressing the timer programming button until the required time is displayed.
T o delete the timer programming,
keep pressing the button until 
is displayed. Y ou can change your programme
selection at any time until the programme starts. End
 of programme
The  end of the programme is indicated by
a buzzer . This function can be changed as
follows:–
Hold down Function button C
pressed and switch on main switch
1, then let the buttons go.
Function Button 
C  flashes, and the
digital display indicates the value 
which was set at the factory (semi-loud). T o change the setting: 
Press Function button 
C .
Each depression of the button increases the set value by one, when
 is reached, the display
jumps back to 
 (of f).
Switch of f the main switch 1. 
The set value is stored in the appliance.
Switching  the dishwasher OFF
Several  minutes after the programme has
ended:
Open the door when the programme has ended.
Set main switch 1 to OFF .
Turn the water tap of f.
(Does not apply when Aqua-Stop unit has been fitted)
Remove dishes, etc. when they have cooled down.
      
						

							en19
Interrupting
 the programme
Open the door . Caution! There is a risk
of water squirting out from inside the appliance. Do not open the door fully until the spray arm has stoppedrotating.
Set main switch 1 to OFF .
Indicator lights extinguish. The programme is retained in the dish- washer memory .
If the hot water was switched ON or the appliance has already heated up and then the appliance door opened, leave the door ajar for several minutes and then close. Otherwise, the appliance door may fly open due to expansion.
In order to continue with the stored programme, set the main switch to ON again and close the door .
Terminating  the programme
(Reset)
Simultaneously  press programme
buttons 
A  and C for approx. 3 sec.
The numerical display indicates 
.
Close the door .
The programme sequence lasts approx. 1 min.
Switch of f the main switch 1.
Changing  the programme
When  the appliance is switched on, the
programme can be changed within minutes. If the programme is changed subsequently , programme sections
(e.g. Cleaning) which have already startedrun to the end. The new remaining timeconsists of the remaining time of theprevious programme section and the remaining time of the newly selected programme. Intensive
 drying
In  the final rinse the appliance operates
at a higher temperature and therefore an improved drying result is obtained. (Caution if utensils are fragile!)
Hold down programme button A  and
press main switch until 
1 the digital
display illuminates.
Release both buttons.
The LED for button 
A  flashes and
the digital display 
4 displays the factory
setting 
 (of f) or  (on).
To change the setting, press
programme button 
A .
Switch of f the main switch 1.
    
						

							en
20 Additional
 functions
*  on  some models additional functions
5 can be set with the buttons.
Saving  time (V arioSpeed) *
The  >>Save time