Siemens Se 60t393 Instructions For Use

en21
Saving
 time (VarioSpeed)
The  Auto Programmes allow you to reduce
the run time of the programmes. However ,
in order to achieve an optimal cleaning result, the water and energy consumptionwill be increased.
If the option “Reduce time” is chosen the display shows “Reduce T ime: Off”
(factory setting).
Select “Reduce time: On”.
Return to the Main Menu by pressing M/OK 
2  and start the required
programme by pressing the Start Button 
4 .
If you do not want to use “Reduce time” the next time you use...

en
22
Language Y
ou can change the language selected
when the appliance was started for the first time (see chapter “Before Starting The Device For The First T ime”).
If the option “Language” is chosen the display shows several languageabbreviations. The abbreviation of the currently selected language is flashing.
In order to choose a different language,
press – or + 
3  until the desired
language appears.
Confirm the language selection by pressing M/OK 
2 .
All following optical character messages will...

en23
Remote
 Options **
The  dishwasher installs itself automatically
during the first use within a serve@Home network. In some cases however , it might
become necessary to start the enrolment 
process anew.
If the option “Remote Options” is selected, the message “Enrol Device” will be displayed. By pressing the button + 
3  you enrol the device
again at the gateway . After successfully
enrolling the device the message “Auto W ash” will be displayed.
If the enrolment is unsuccessful the display shows “no...

en
24
Interrupting
 the programme
In order to interrupt the programme,
open the door . In order to avoid water
escaping, only open the door slightly first.The message “Cancel Programme” will be displayed, alternating with the message “Close the door”, the remaining programme time, the selected programme, and the current programme phase.
In order to interrupt, do not in anycircumstance press the button – 
3
“Cancel Programme” because this will not allow the programme to continue!
T o continue the...

en25
Maintenance
 and care
A  regular inspection and maintenance of
your machine will help to prevent faults. This saves time and prevents problems. Overall  condition of the
machine
Check  washing chamber for grease
and limescale deposits.
If you find such deposits:
Fill the detergent dispenser with detergent, start the appliance withoututensils in the programme which has the highest wash temperature.
Clean the appliance with detergents/ appliance cleaners which are particularly suitable for use with...

en
26
Reassembly: Insert the filter system and screw downwith the filter cylinder .Spray arms
Lime  and remnants of food in the washing
water can block the nozzles in the spray arms 
24  and 25 and the arm
mountings .
Inspect the nozzles in the spray arms for blocked holes due to remnants offood.
If necessary , pull the lower arm 25
upwards and lift it of f.
Unscrew the upper spray arm 24.
Clean both spray arms under running 
water.
0
1
2
3
Refit the spray arms. Ensure that the lower arm has locked into...

en27
Pump
 *
*  on applicable models
Larger remnants of food that have not been trapped by the filters and have been left in the water can cause a blockage in the pump. The water is no longer pumped out of the dishwasher and it can be seencovering the filter .
Proceed as follows:
First, always disconnect the appliance from the power supply .
Ladle out as much water as possible.
Remove the filters 27.
Undo the screw in the cover (T orx T 20)
and remove the cover .
Inspect the inside and remove any...

en
28
Some time after the programme start a continuous acoustic signalsounds. The device does not draw water .
When the door is opened the message “Check water supply”is displayed.
Mains water tap is not opened.  Open the tap fully and press the button M/OK 
2  of the device.
Then close the device’ s door for
the programme to resume.
Filter of the water inlet hose is blocked. Switch of f the device and
disconnect it from the powersupply . Close the mains water tap.
Clean the filter located at the...

en29
Appliance stops suddenly while washing is taking place
Cut in electricity supply to appliance.
Water supply has been
interrupted.
Knocking sound can be heard while washing is taking place
A spray arm is knocking against the dishes inside the appliance.
Rattling sound can be heard while washing is taking place
Crockery has not been stacked properly inside the appliance.
Knocking sound coming from inlet valves
This is caused by the way the water pipes have been laid and it has no ef fect upon the way...

en
30
Smears left behind on glasses and cutlery; glasses have acquired ametallic appearance
Amount of rinse-aid set too high.
...  serve@Home
The  dishwasher cannot be
operated via serve@Home.
The device is not connected to the network.
The device is not ready for serve@Home.
The System Interface is not installed.
Customer  Service
Please  call your local service agent, if you
are not able to resolve any problem yourself. The name of your nearest service agent is shown in the Customer Service address...