Sharp Xv Z2000 Projector User Manual

							-60
PC control
A computer can be used to control the projector by connecting an RS-232C cable (null modem, cross type,
commercially available) to the projector. (See page 27 for connection.)
Communication conditions
Set the serial port settings of the computer to match that of the table.
Signal format: Conforms to RS-232C standard.
Baud rate: 9,600 bps
Data length: 8 bits
Parity bit: None
Stop bit: 1 bit
Flow control: None
Basic format
Commands from the computer are sent in the following order: command, parameter, and return code. After
the projector processes the command from the computer, it sends a response code to the computer.
Info
•When more than one code is being sent, send each command only after the OK response code for the
previous command from the projector is verified.
•When using the computer control function of the projector, the projector’s operating status cannot be read by
the computer.
Commands
Example:
•When power on.
Response code format
Normal response
Problem response (communication error or incorrect command)
Command format
RS-232C Specifications and Command Settings
Return code (0DH)C1    C2    C3   C4    P1    P2    P3    P4
Command 4-digitParameter 4-digit
O      KReturn code (0DH) E      R      RReturn code (0DH)
Note
•If an underbar (_)  appears in the parameter column, enter a space.
→
←POWR_1 __OK
Projector Computer
CONTROL CONTENTS
POWER ON
STANDBY
INPUT 1 (COMPONENT 1)
INPUT 2 (COMPONENT 2)
INPUT 3 (S-VIDEO)
INPUT 4 (VIDEO)
INPUT 5 (RGB/COMPONENT)
DIGITAL MODEOK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR P
P
I
I
I
I
I
IO
O
V
V
V
V
V
VW
W
E
E
E
E
E
ER
R
D
D
D
D
D
D_
_
_
_
_
_
_
__
_
_
_
_
_
_
__
_
_
_
_
_
_
_1
0
1
2
3
4
5
6
BUTTONS & REMOTE CONTROL BUTTONS
COMMANDPARAMETERRETURN
XV-Z2000U_E_P53_61.p6504.10.13, 0:21 PM 60 
						

							-61
Appendix
Note
•This projector may not be able to display images from notebook computers in simultaneous (CRT/LCD)
mode. Should this occur, turn off the LCD display on the notebook computer and output the display data
in “CRT only” mode. Details on how to change display modes can be found in your notebook computer’s
operation manual.
Computer Compatibility Chart
•Horizontal Frequency: 15–70 kHz
Vertical Frequency: 43–75 Hz
Pixel Clock: 12–80 MHz
Compatible with sync on green
XGA compatible in intelligent compression
DTV
Computer
The table below lists signal codes that are compatible with the projector. When the images are distorted or
cannot be projected, adjust the output signal of your computer and so forth while referring to the table below.
15.7
31.5
33.8
15.6
31.3
45.0
28.1
33.8
28.1
33.8 480I480P
540P
576
I576P
720P
1035
I1035I1080I1080I
60
60
60
50
50
60
50
60
50
60Signal Vertical Frequency (Hz)Horizontal Frequency (kHz)
PC/
MAC/
WSHorizontal
Frequency
(kHz)Vertical
Frequency
(Hz)
VGA
PC
SVGA
XGAVESA
StandardDVI
Support
✔
✔ ✔
✔ ✔ ✔
✔✔
✔
✔ ✔
✔ ✔
✔ ✔
✔
✔
✔
✔
✔
✔ ✔
✔
✔ Resolution
640 × 350
720 × 350
640 × 400
720 × 400
640 × 480
800 × 600
1,024 × 768Display
Upscale
Intelligent 
Compression 27.0 60
27.0 60
27.0 60
60 31.5 70
31.5 70
31.5
70
31.5
60
34.7
70
37.9
72
37.5
75
31.4 50
35.1 56
37.9 60
44.5 70
48.1 72
46.9 75
✔ 31.5 70
27.0
26.2
50
35.5 43
40.3 50
58.1 72 56.5 70
1,280 × 720 —
45.0 60
MAC 16PC/
MAC 13
PC/
MAC 19640 × 480
832 × 624
Intelligent
Compression 34.9 67
60.0 1,024 × 768 VGA
SVGA
✔ ✔
XGA48.4 60
75 46.8 75
49.6 75Upscale
XV-Z2000U_E_P53_61.p6504.10.14, 1:16 PM 61 
						

							-62
Troubleshooting
Check
•Projector power cord is not plugged into the wall outlet.
•Power to the external connected devices is off.
•The selected input mode is wrong.
•Cables are incorrectly connected to the rear panel of the projector.
•External output has not been set when connecting notebook computer.
•“Contrast” and “Bright” are set to minimum position.
•Image adjustments are incorrectly set.
(Video Input only)
•Video input system is incorrectly set.
(INPUT 5)
•Input signal type (RGB/Component) is incorrectly set.
•“OSD Display” is set to “ (OFF)”.
•Adjust the focus.
•The projection distance exceeds the focus range.
(Computer Input only)
•Perform “Fine Sync” Adjustments. (“Clock” Adjustment)
•Perform “Fine Sync” Adjustments. (“Phase” Adjustment)
•Noise may appear depending on the computer.
•If the picture is normal, the sound is due to cabinet shrinkage
caused by room temperature changes. This will not affect
operation or performance.
•See “Maintenance Indicators”.
•When temperature inside the projector increases, the cooling
fan runs faster.
•The lamp will eventually need to be changed.
The lamp has reached the end of its life. Replace the lamp.
•Change the input signal type.
Problem
On-screen display does
not appear.
An unusual sound is
occasionally heard
from the cabinet.
Maintenance
indicator illuminates or
blinks in red.
The cooling fan
becomes noisy.
The lamp takes a long
time to turn on.
Picture is dark.
Image is green on
INPUT 5 Component.
Image is pink (no green)
on INPUT 5 RGB.
Page
28
—
29
19-27
—
42
42
48
48
47
30
17
45
45
—
—
54
—
57
48
Color is faded or poor.
Picture is blurred;
noise appears.
No picture
This projector is equipped with a microprocessor. Its performance could be adversely affected by
incorrect operation or interference. If this should happen, unplug the Unit and plug it in again after
more than 5 minutes.
If you encounter any problems during setup or operation of this projector, first refer to the
“Troubleshooting” section on this page. If this operation manual does not answer your ques-
tion, please call toll free 1-877-DTV-SHARP (1-877-388-7427) for further assistance. Or, send
us an e-mail at [email protected] .
Our World Wide Web address is http://www.sharpusa.com/ .
For SHARP Assistance (U.S.A. only)
XV-Z2000U_E_P62_68.p6504.10.13, 0:21 PM 62 
						

							-63
Appendix
Specifications
Product typeModel
V ideo system
Display method DLP panel
Lens
Projection lamp
V ideo input signal
S-video input signal
Component input signal (INPUT 1, 2)
Analog RGB/Digital (INPUT 5/DIGITAL)
Horizontal resolution Pixel clock
Ve rtical frequency
Horizontal frequency
Computer control signal Rated voltageInput current
Rated frequency
Power consumption
Power consumption (standby)Heat dissipation
Operating temperature Storage temperature
Cabinet
I/R carrier frequency
Dimensions (approx.)
Weight (approx.)
Supplied accessories
Replacement parts Projector
XV-Z2000
P
AL/PAL 60/PAL-M/PAL-N/SECAM/NTSC 3.58/NTSC 4.43
DTV 480
I/480P/720P/1080ISingle Panel Digital Micromirror Device (DMD™) by Texas Instruments
Panel size: 0.8
Drive method: Digital Light Processing (DLP™)
No. of dots: 921,600 dots (1,280 [H]  × 720 [V])
1–1.5  × zoom lens, F2.0–2.5 f=21.3–31.6 mm
275 W DC lamp
RCA Connector: VIDEO (INPUT 4), composite video, 1.0 Vp-p, sync negati\
ve, 75  Ω
terminated
4-pin Mini DIN connector (INPUT 3)
Y (luminance signal): 1.0 Vp-p, sync negative, 75  Ω terminated
C (chrominance signal): Burst 0.286 Vp-p, 75  Ω terminated
RCA Connector
Y:  1.0 Vp-p, sync negative, 75  Ω  terminated
P
B (CB): 0.7 Vp-p, 75  Ω  terminated
PR (CR): 0.7 Vp-p, 75  Ω  terminated
29-pin DVI-I terminal

Input impedance 50  Ω
Input level 250-1000 mV

Input impedance 75  Ω
Input level 0.7 Vp-p
Y:  1.0 Vp-p, sync negative, 75  Ω terminated
P
B (CB): 0.7 Vp-p, 75  Ω  terminated
PR (CR): 0.7 Vp-p, 75  Ω  terminated

•
• •
•
• Separate sync/Composite sync
Input level TTL level
Input impedance 1 K Ω
•
• •
•
• Green on sync
Input level (Synchronizing input) 0.286 Vp-p
Input impedance 75  Ω
720 TV lines (DTV 720P input)
12–80 MHz
43–75 Hz
15–70 kHz
9-pin D-sub connector (RS-232C Port)
AC 100–240 V
3.65 A (When using AC 100 V)
50/60 Hz
360 W (When using AC 100 V)
6 W (When using AC 100 V)
1,350 BTU/hour
41°F to 95°F (+5°C to +35°C)
–4°F to 140°F (–20°C to +60°C)
Plastic
38 kHz
12 
7/32  ×  3 33/64  × 11 7/64 (310 (W)  × 89 (H)  × 282 (D) mm)
9.5 lbs. (4.3 kg)
Remote control, Two AA size batteries, Power cord, Lens cap (attached on the body),
Operation manual
Lamp unit (Lamp/cage module) (AN-K2LP), Remote control (RRMCGA334WJSA), AA
size batteries, Power cord (QACCDA007WJPZ), Lens cap (PCAPHA021WJSA),
Operation manual (TINS-B529WJZZ)
As a part of policy of continuous improvement, SHARP reserves the right to make design
and specification changes for product improvement without prior notice. The performancespecification figures indicated are nominal values of production units. There may be somedeviations from these values in individual units.
XV-Z2000U_E_P62_68.p65 04.10.15, 14:44
63 
						

							-64
Dimensions
Units: inches (mm)
Side ViewSide ViewTop View
Rear View
Front View
Bottom View
M4 M4
M4M4
9/64 (3.25)
11
 7/64 (282)
1/16 (1.5)
2 11/64 (55.05) 12
 7/32 (310)
1 59/64 
(48.5) 3
 33/64 (89)
13/64 (5)
2
 3/16 
(55.5)
3 15/16 (99.95)
5
 7/64 (129.5) 5 7/64 (129.5)
5/8 (15.5)9/16 (14)
4 3/16 (106.3)
8
 9/32 (210.3)
8 7/8 (225.3)
1 7/32 
(30.9) 1 5/32 
(29.1)
1
 7/32 
(30.9) 1 3/4 
(44.1)
XV-Z2000U_E_P62_68.p6504.10.13, 0:21 PM 64 
						

							-65
Appendix
Glossary
Aspect Ratio
Width and height ratio of an image. The normal
aspect ratio of a computer and video image is 4:3.
There are also wide images with an aspect ratio
of 16:9 and 21:9.
Auto Sync
Optimizes projected computer images by auto-
matically adjusting certain characteristics.
Background
Initial setting image projected when no signal is
being output.
Clock
Clock adjustment is used to adjust vertical noise
when clock level is incorrect.
CLR Temp (Color temperature)
Function that can be used to adjust the color tem-
perature to suit the type of image input to the pro-
jector. Decrease the color temperature to create
warmer, reddish images for natural flesh tones,
or increase to create cooler, bluish images for a
brighter picture.
Composite sync
Signal combining horizontal and vertical sync
pulses.
DVI (Digital Visual Interface)
Display digital interface that also supports analog
interfaces.
Intelligent compression and expansion
High quality resizing of lower and higher resolu-
tion images to fit the projector’s native resolution.
Keystone Correction
Function to digitally correct a distorted image when
the projector is set up at an angle, smoothes out
jaggies on keystone images and compresses the
image not only horizontally but vertically keeping
the 16 : 9 aspect ratio.
Phase
Phase shift is a timing shift between isomorphic
signals with the same resolution. When phase level
is incorrect, the projected image typically displays
horizontal flicker.
Resize
Allows you to modify or customize the picture dis-
play mode to enhance the input image. You can se-
lect from four different modes: STRETCH, SIDE
BAR, SMART STRETCH and CINEMA ZOOM.
RS-232C
Function to control the projector from the com-
puter by using the RS-232C ports on the projec-
tor and computer.
Stretch
Mode that stretches the 4:3 image horizontally to
display it on the wide screen.
Gamma
Image quality enhancement function that offers a
richer image by brightening the darker portions
of the image without altering the brightness of the
brighter portions. You can select from four differ-
ent modes: Standard, Cinema 1, Cinema 2 and
Cinema 3.
XV-Z2000U_E_P62_68.p6504.10.14, 1:19 PM 65 
						

							-66
Index
A
AC socket ............................................................. 28
Adjustment buttons .............................................. 38
Aspect ratio .......................................................... 35
Auto Power Off ..................................................... 50
A uto Sync ............................................................. 46
AU TO  SYNC button ............................................. 46
B
Background .......................................................... 49
Blue ...................................................................... 42
Bright .................................................................... 42
Bright Boost ......................................................... 43
C
Ceiling+Front ........................................................ 52
Ceiling+Rear ........................................................ 52
Clock .................................................................... 45
CLR Temp  (Color Temperature) ........................... 42
Color ..................................................................... 42
Component terminals ........................................... 21
Contrast ................................................................ 42
D
DIGITAL INPUT button ......................................... 29
DV I........................................................ 22,23,25,26
E
Eco Mode ............................................................. 49
ENTER button ...................................................... 39
Exhaust vent ................................................ 7,11,53
F
Fine Sync ............................................................. 45
Front ..................................................................... 52
G
Gamma Adj. ......................................................... 43
H
HEIGHT ADJUST button ...................................... 31
H-Pos ................................................................... 45
I
INPUT buttons ...................................................... 29
Intake vent ......................................................... 7,53
IRIS ................................................................. 34,44
IRIS button ........................................................... 34
K
Kensington Lock .................................................. 11
KEYSTONE button ............................................... 32
Keystone Correction ............................................. 32
L
Lamp .................................................................... 56
Lamp indicator ..................................................... 54
Lamp Timer  (Life) ................................................. 47
Language ............................................................. 52
Lens cap ................................................................. 9
M
MENU button ........................................................ 38
Menu Color ........................................................... 51
Menu Position ....................................................... 50
O
ON button ............................................................. 28
On-screen display language ................................ 52
OSD Display ......................................................... 47
P
Phase ................................................................... 45
Picture .................................................................. 42
Picture Mode ........................................................ 44
PICTURE MODE button ...................................... 34
Power cord ........................................................... 28
Po wer indicator ..................................................... 10
PRJ mode ............................................................ 52
R
Rear ..................................................................... 52
Rear adjustment feet ............................................ 31
Red ....................................................................... 42
Remote control ..................................................... 12
Remote control sensor ......................................... 13
Replacing the lamp .............................................. 56
RESIZE button ..................................................... 34
RS-232C terminal ................................................ 27
S
Sharp .................................................................... 42
Signal Info ............................................................ 46
Signal Type .......................................................... 48
Special Modes ..................................................... 45
STANDBY button ................................................. 28
STRETCH ............................................................ 35
S-video input terminal .......................................... 24
T
T emperature warning indicator ............................. 54
Tint ....................................................................... 42
U
UNDO button ........................................................ 34
V
Video input terminal ............................................. 24
Video System ....................................................... 48
V-Po s.................................................................... 45
Z
ZOOM/FOCUS button .......................................... 30
XV-Z2000U_E_P62_68.p65 04.10.15, 14:44
66 
						

							-67
Appendix
CONSUMER LIMITED WARRANTY
SHARP ELECTRONICS CORPORATION warrants to the first consumer purchaser that this Sharp brand product (the “Product”),
when shipped in its original container, will be free from defective workmanship and materials, and agrees that it will, at its option, either
repair the defect or replace the defective Product or part thereof with a new or remanufactured equivalent at no charge to the purchaser
for parts or labor for the period(s) set forth below.
This warranty does not apply to any appearance items of the Product nor to the additional excluded item(s) set forth below nor to any
Product the exterior of which has been damaged or defaced, which has been subjected to improper voltage or other misuse, abnormal
service or handling, or which has been altered or modified in design or construction.
In order to enforce the rights under this limited warranty, the purchaser should follow the steps set forth below and provide proof of
purchase to the servicer.
The limited warranty described herein is in addition to whatever implied warranties may be granted to purchasers by law. ALL IMPLIED
WARRANTIES INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR USE ARE LIMITED
TO THE PERIOD(S) FROM THE DATE OF PURCHASE SET FORTH BELOW. Some states do not allow limitations on how long an
implied warranty lasts, so the above limitation may not apply to you.
Neither the sales personnel of the seller nor any other person is authorized to make any warranties other than those described herein,
or to extend the duration of any warranties beyond the time period described herein on behalf of Sharp.
The warranties described herein shall be the sole and exclusive warranties granted by Sharp and shall be the sole and exclusive
remedy available to the purchaser. Correction of defects, in the manner and for the period of time described herein, shall constitute
complete fulfillment of all liabilities and responsibilities of Sharp to the purchaser with respect to the Product, and shall constitute full
satisfaction of all claims, whether based on contract, negligence, strict liability or otherwise. In no event shall Sharp be liable, or in any
way responsible, for any damages or defects in the Product which were caused by repairs or attempted repairs performed by anyone
other than an authorized servicer. Nor shall Sharp be liable or in any way responsible for any incidental or consequential economic or
property damage. Some states do not allow the exclusion of incidental or consequential damages, so the above exclusion may not
apply to you.
THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE
TO STATE.
Model Specific Section (In-Home Service)
Your Product Model Number & Description:
Warranty Period for this Product:
Additional Item(s) Excluded fromWarranty Coverage (if any):
Where to Obtain Service:
What to do to Obtain Service:XV-Z2000 Projector
(Be sure to have this information available when you need service
for your Product.)
One (1) year parts and labor from date of purchase except for the
Projector Lamp for which the warranty period is ninety (90) days
from date of purchase. After the ninety (90) day warranty period on
the Projector Lamp, parts and labor for a lamp replacement are the
responsibility of the consumer.
Cleaning of Optical System and/or replacement of any filter.
Labor & materials required to remove and reinstall a suspended
projector in installations not accessible with a standard (8 step)
ladder or ceilings exceeding 12’ in height.
Labor & materials required to remove and reinstall a projector in
complex systems including, but not limited to, projectors installed
in custom enclosures, projectors connected to third party control
and automation systems, and realignment of projectors installed in
“mirrored” rear projection enclosures.
From a Sharp Authorized Servicer located in the United States. To
find the location of the nearest Sharp Authorized Servicer, call Sharp
toll free at 1-800-BE-SHARP.
Contact your Sharp Authorized Servicer to obtain in-home service
for this Product. The Servicer will come to your home and if
necessary to remove the Product for repair at the Servicer’s facility,
the Servicer will reinstall it upon completion of repair. Be sure to
have Proof of Purchase available.
VALID IN USA ONLY
TO OBTAIN PRODUCT INFORMATION, CALL 1-877-DTV-SHARP OR VISIT  www.sharpusa.com.
XV-Z2000U_E_P62_68.p6504.10.14, 1:20 PM 67 
						

							-68
LIMITED WARRANTY
Consumer Electronics Products
Congratulations on your purchase!
Sharp Electronics of Canada Ltd. (hereinafter called “Sharp”) gives the following express warranty to the first consumer purchaser for
this Sharp brand product, when shipped in its original container and sold or distributed in Canada by Sharp or by an Authorized Sharp
Dealer:
Sharp warrants that this product is free, under normal use and maintenance, from any defects in material and workmanship. If any
such defects should be found in this product within the applicable warranty period, Sharp shall, at its option, repair or replace the
product as specified herein.
This warranty shall not apply to:
(a)Any defects caused or repairs required as a result of abusive operation, negligence, accident, improper installation or inappropriate
use as outlined in the owner’s manual.
(b) Any Sharp product tampered with, modified, adjusted or repaired by any party other than Sharp, Sharp’s Authorized Service
Centres or Sharp’s Authorized Servicing Dealers.
(c) Damage caused or repairs required as a result of the use with items not specified or approved by Sharp, including but not limited
to head cleaning tapes and chemical cleaning agents.
(d) Any replacement of accessories, glassware, consumable or peripheral items required through normal use of the product including
but not limited to earphones, remote controls, AC adapters, batteries, temperature probe, stylus, trays, filters, belts, ribbons,
cables and paper.
(e) Any cosmetic damage to the surface or exterior that has been defaced or caused by normal wear and tear.
(f) Any damage caused by external or environmental conditions, including but not limited to transmission line/power line voltage or
liquid spillage.
(g) Any product received without appropriate model, serial number and CSA/cUL markings.
(h) Any products used for rental or commercial purposes.
(i) Any installation, setup and/or programming charges.
Should this Sharp product fail to operate during the warranty period, warranty service may be obtained upon delivery of the Sharp
product together with proof of purchase and a copy of this LIMITED WARRANTY statement to an Authorized Sharp Service Centre
or an Authorized Sharp Servicing Dealer. In home warranty service may be provided at Sharp’s discretion on any Sharp television
with the screen size of 27” or larger and on any Sharp Over The Range Microwave Oven.
This warranty constitutes the entire express warranty granted by Sharp and no other dealer, service centre or their agent or employee
is authorized to extend, enlarge or transfer this warranty on behalf of Sharp. To the extent the law permits, Sharp disclaims any and
all liability for direct or indirect damages or losses or for any incidental, special or consequential damages or loss of profits resulting
from a defect in material or workmanship relating to the product, including damages for the loss of time or use of this Sharp product
or the loss of information. The purchaser will be responsible for any removal, reinstallation, transportation and insurance costs
incurred. Correction of defects, in the manner and period of time described herein, constitute complete fulfillment of all obligations
and responsibilities of Sharp to the purchaser with respect to the product and shall constitute full satisfaction of all claims, whether
based on contract, negligence, strict liability or otherwise.
WARRANTY PERIODS
Projector 1 year (bulb 90 days)
To obtain the name and address of the nearest Authorized Sharp Service Centre or Dealer, please contact:
SHARP ELECTRONICS OF CANADA LTD.
SHARP ELECTRONICS OF CANADA LTD.
335 Britannia Road East
Mississauga, Ontario
L4Z 1W9
(905) 568-7140
Web site: www.sharp.ca
VALID IN CANADA ONLY
XV-Z2000U_E_P62_68.p6504.10.13, 0:22 PM 68 
						

							XV-Z2000
XV -
Z2000ENGLISH
FRANÇAIS
ESP AÑOL
PORTUGUÊS
OPERATION MANUAL
MODE D’EMPLOI
MANUAL DE OPERACION
MANUAL DE OPERAÇÃO
PROJECTOR
PROJECTEUR
PROYECTOR
PROJETOR
Printed in China
Imprimé en Chine
Impreso en China
Impresso na China
TINS-B529WJZZ
04P11-CNM
SHARP CORPORATION
XV-Z2000U_E_Hyo1_4.p65
04.10.14, 1:13 PM
1