Sharp Xv Z12000 Projector User Manual

							-40
Menu Bar Items
This list shows the items that can be set in the projector.

 INPUT 1 / 2 / 5 Mode
* In INPUT 5, the items in “Signal Type” are “D. PC RGB”, “D. PC Comp.”, “D. Video RGB”, “D. Video Comp.”
“A. RGB” and “A. Comp.”.
Note
•The resolution, vertical frequency and horizontal frequency figures displayed above are for example
purposes only.
•Picture adjustment settings differ depending on the type of input signal.
Signal Type
RGB
Component*
Standard
Black Detail
Dynamic Gamma
Custom 1
Custom 2
SVM Gamma
Standard
Natural
Dynamic
Custom 1
Custom 2
INPUT1/2/5 Position
Standard
Film Tone
Custom 1
Custom 2
+30 –30+30 –30
+30 –30
+30 –30+30 –30
11000 5000
Main menu Sub menuMain menu Sub menu
Contrast Picture Position
Bright
Color
Tint
Sharp
Reset
CLR Temp
Gamma Position
C.M.S. Position
Specials
IP Mode
[2D/3D/Film]
White Emph [ON/OFF]
DNR [OFF/Level 1-3]
DFC [OFF/Level 1-3] Picture
Page 46
+30 –30+30 –30
+30 –30
C.M.S. Position
Target 
Lightness
Chroma
Hue
Reset (This Color)
Reset (All Colors)
View Settings
R-Gamma G-Gamma
B-Gamma
R-Gain
G-GainB-Gain
R-OffsetG-OffsetB-OffsetReset
[R] Red
[Y] Yellow
[G] Green
[C] Cyan
[B] Blue
[M] Magenta C.M.S.
Page 54
Gamma PositionStandard
Black Detail
Dynamic Gamma
Custom 1
Custom 2
SVM Gamma GammaPage 52
Standard
Film Tone
Custom 1
Custom 2
+150 –150
+150 –150+60 –60
+60 –60
1
2•
•7
1
2
•
•7
1
2
3
4
•
•7Resolution
1024 × 864
1152 × 864
1152 × 870
1152 × 882 Resolution
1024 × 768
  800 × 600Vert Freq
60 Hz
75 Hz
Resolution
1024 × 768
 800 × 600Vert Freq
60 Hz
75 Hz
1024 × 768
48.4 KHz
60 Hz Fine Sync
Page 57Clock
Phase
H-Pos
V-Pos
Reset
Save Setting
Select Setting
Special Modes
Signal Info
Auto Sync
Auto Sync Disp [ON/OFF]
Resolution
Hor Freq
Vert Freq
OFF
Normal
High Speed
Options
Page 66
Reset
Lamp Timer
LED [ON/OFF]
OSD Display
Background
Economy Mode
Power Save [ON/OFF]
RS-232C Port [ON/OFF]
Auto Power Off [ON/OFF]
Normal
Level A
Level B
Blue
None
PRJ Mode
Subtitle
Front
Ceiling + Front
Rear
Ceiling + Rear RS-232C
9600 bps
38400 bps
115200 bps
English
Deutsch
Español
Nederlands
Français
Italiano
Svenska
Português Language
Page 36
Status
Page 74
Digi. Shift+30 –30
+30 –30
+30 –30
+30 –30
+30 –30
+30 –30
+30 –30
+30 –30
+30 –30
+30 –30
+30 –30
XV_Z12000_E_US_p33_41.p6503.9.24, 2:00 PM 40 
						

							Basic Operation
-41

 INPUT 3 / 4 Mode
English
Deutsch
Español
Nederlands
Français
Italiano
Svenska
Português
Page 74 +30 –30
+30 –30
+30 –30
+30 –30
+30 –30
11000 5000
Main menu Sub menu
Main menu Sub menu
Picture
Page 46
Contrast
Bright
Color
Tint
Sharp
CLR Temp
Specials
PRJ Mode
Front
Ceiling + Front
Rear
Ceiling + Rear RS-232C
9600 bps
38400 bps
115200 bps
Language
Page 36
Status
+30 –30+30 –30
+30 –30
C.M.S. Position
Target 
Lightness
Chroma
Hue
Reset (This Color)
Reset (All Colors)
View Settings[R] Red
[Y] Yellow
[G] Green
[C] Cyan
[B] Blue
[M] Magenta C.M.S.
Page 54
LED [ON/OFF]
OSD Display
Video System
BackgroundNormal
Level A
Level B
Auto
PAL (50/60Hz)
SECAM
NTSC4.43
NTSC3.58
PAL-M
PAL-N
Blue
None
Economy Mode
Options
Page 66
Power Save [ON/OFF]
RS-232C Port [ON/OFF]
Auto Power Off [ON/OFF]
Standard
Black Detail
Dynamic Gamma
Custom 1
Custom 2
SVM Gamma
Standard
Film Tone
Custom 1
Custom 2 Gamma Position
C.M.S. Position
ResetDigi. Shift
Subtitle
Reset
Lamp Timer
R-Gamma G-Gamma
B-Gamma
R-Gain
G-GainB-Gain
R-OffsetG-OffsetB-OffsetReset
Gamma PositionStandard
Black Detail
Dynamic Gamma
Custom 1
Custom 2
SVM Gamma GammaPage 52+30 –30
+30 –30
+30 –30
+30 –30
+30 –30
+30 –30
+30 –30
+30 –30
+30 –30+30 –30
+30 –30
Picture Position
Standard
Film Tone
Custom 1
Custom 2
Standard
Natural
Dynamic
Custom 1
Custom 2
INPUT3/4 Position
IP Mode
[2D/3D/Film]
White Emph [ON/OFF]
DNR [OFF/Level 1-3]
DFC [OFF/Level 1-3]
XV_Z12000_E_US_p33_41.p6503.9.24, 2:00 PM 41 
						

							This projector has two sets of menu screens that allow you to adjust the image and various
projector settings.
You can operate the menus from the projector or remote control using the following proce-
dure.
Using the Menu Screen
Menu screen for INPUT 1,
INPUT 2 or INPUT 5 ModeMenu screen for INPUT 3 or
INPUT 4 Mode
Menu Bar
(Main Menu)
" "" "
"Menu Screen
Menu Selections
(Adjustments)
1Press .
•The menu screen is displayed.
Note
•The “Picture” menu screen for the
selected input mode is displayed.
•The on-screen display shown on the
lower right is displayed when the IN-
PUT 1, 2 or 5 mode is selected.
Menu Bar
(Main Menu)
MENU button " "" "
", 
' '' '
', 
\ \\ \
\, 
| || |
|
buttons
ENTER button
MENU button
ENTER
button
" "" "
", 
' '' '
', 
\ \\ \
\, 
| || |
|
buttons
-42
XV_Z12000_E_US_p42_60.p6503.9.24, 2:01 PM 42 
						

							Basic Operation
-43
2Press 
\ \\ \
\ or 
| || |
| to select the
menu you want to adjust.
Note
•For details on the menus, see the
tree charts on pages 40 and 41.
3Press 
" "" "
" or 
' '' '
' to select the item
you want to adjust.
Note
•To display a single adjustment item,
press 
 after selecting the item.
Only the menu bar and the selected
adjustment item will be displayed.
Then if you press " or ', the fol-
lowing item (“Bright” after “Con-
trast”) will be displayed.
•Press 
  to return to the previous
screen.
4Press 
\ \\ \
\ or 
| || |
| to adjust the item
selected.
•The adjustment is stored.
5Press .
•The menu screen will disappear.
| || |
|
XV_Z12000_E_US_p42_60.p6503.9.24, 2:01 PM 43 
						

							
 Menu screen
Menu Selections
(Settings)
1Press .
•The menu screen is displayed.
Note
•The “Picture” menu screen for the
selected input mode is displayed.
•The on-screen displays shown on
the lower right are displayed when
INPUT 1, 2 or 5 mode is selected.
2Press 
\ \\ \
\ or 
| || |
| to select the
menu you want to adjust.
Note
•For details on the menus, see the
tree charts on pages 40 and 41.
3Press 
" "" "
" or 
' '' '
' to select the
item you want to set.
Note
•Press  to return to the previous
screen.
•In some menus, select the icon us-
ing “
”.
Using the Menu Screen
MENU button " "" "
", 
' '' '
', 
\ \\ \
\, 
| || |
|
buttons
ENTER button
MENU button
ENTER
button
" "" "
", 
' '' '
', 
\ \\ \
\, 
| || |
|
buttons
-44
Sub menu
XV_Z12000_E_US_p42_60.p6503.9.29, 11:37 AM 44 
						

							Basic Operation
-45
4Press 
| || |
|.
•The cursor shifts to the sub menu.
5Press 
" "" "
" or 
' '' '
' to select the set-
ting of the item displayed in the
sub menu.
6Press .
•The item selected is set.
Note
•Some adjustment items will display
a confirmation message.
When setting an item, press \ or
| to select “Ye s” or “OK” and then
press 
.
•Use 
 to select “ON” or “OFF” for
the item of “Economy Mode”.
•Use 
 to select setting for the item
of “Specials” in the “Picture” menu.
7Press .
•The menu will disappear.
Sub menu
XV_Z12000_E_US_p42_60.p6503.9.24, 2:01 PM 45 
						

							Adjusting the Picture
You can adjust the projector’s picture to your preferences with the following picture settings.
-46
Selecting the Picture
Position
This function allows you to select the picture
position in accordance with brightness of the
room or content of the software to be played.
There are three preset positions and three po-
sitions for custom settings.
In all picture positions, items on the “Picture”
menu can be adjusted and saved. When sav-
ing, select a picture position before setting on
the “Picture” menu.
Select “Picture Position” in the “Pic-
ture” menu on the menu screen.
➝For operating the menu screen, see
pages 42 to 45.
Note
•The picture position can be selected di-
rectly by pressing 
. The position
changes in order each time 
 is pressed.
Description
Sharp default setting
A balanced color image
is obtained.
A vivid image is obtained.
Allows you to store the
picture adjustment
settings to your prefer-
ence.
Picture adjustment
settings can be stored for
each input mode.
Selected Position
Standard
Natural
Dynamic
Custom 1
Custom 2
INPUT1 Position
to
INPUT5 Position
PICTURE POSITION
button
XV_Z12000_E_US_p42_60.p6503.9.24, 2:01 PM 46 
						

							Basic Operation
-47
Adjusting Image Prefer-
ences
Adjust the “Picture” menu on the
menu screen.
➝For operating the menu screen, see
pages 42 to 45.
Note
•Picture adjustment settings differ depend-
ing on the type of input signal.
•Some items may not be adjustable de-
pending on the combination of the INPUT
mode and “Signal Type” setting.
Contrast
Bright
Color
Tint
Sharp
CLR TempFor adjusting the contrast level
For adjusting the brightness of an image
For adjusting the color intensity of an image
For adjusting the tones of an image
For making sharper or softer the contour of an image
For adjusting the color temperature of an imageFor less contrast
For less brightness
For less color intensity
Skin tones become purplish
For less sharpness
Decreases color
temperature for warmer,
reddish, incandescent-
like images.
For more contrast
For more brightness
For more color intensity
Skin tones become greenish
For more sharpness
Increases color
temperature for cooler,
bluish, fluorescent-like
images.
Selected Item Description
\ button| button
Selecting the Gamma
Position
This function allows you to select the desired
gamma position.
Select “Gamma Position” in the “Pic-
ture” menu on the menu screen.
➝For operating the menu screen, see
pages 42 to 45.
Note
•Gamma can be adjusted in greater detail
with “Gamma” on the menu screen. See
page 52 for details.
XV_Z12000_E_US_p42_60.p6503.9.24, 2:01 PM 47 
						

							-48
Selecting the C.M.S.
Position
This function allows you to select the desired
color reproduction mode.
Select “C.M.S. Position” in the “Picture”
menu on the menu screen.
➝For operating the menu screen, see
pages 42 to 45.
Note
•Color can be adjusted in greater detail with
“C.M.S.” on the menu screen. See page
54 for details.
Special Settings
Select “Specials” in the “Picture” menu on the
menu screen.
➝For operating the menu screen, see
pages 42 to 45.
-48
Adjusting the Picture
Description
For selecting the pro-
gressive display of a
video signal (Page 49)
For emphasizing the
contrast (Page 50)
For reducing image noise
(Page 50)
For emphasizing outlines
in the image (Page 51)
Selected Item
IP Mode
White Emph
DNR
DFC
XV_Z12000_E_US_p42_60.p6503.9.24, 2:02 PM 48 
						

							Basic Operation
-49
IP Mode
This function allows you to select the progres-
sive display of a video signal. The progres-
sive display projects a smoother video image.
Select “IP Mode” in the “Specials”
menu on the “Picture” menu screen.
•“IP Mode” is switched by pressing 
.
➝For operating the menu screen, see
pages 42 to 45.
*The film source is a digital video recording with the
original encoded as is at 24 frames/second. The pro-
jector can convert this film source to progressive video
at 60 frames/second with NTSC and PAL60Hz or at
50 frames/second with PAL50Hz and SECAM to play
back a high-definition image.
Note
•When using progressive inputs, inputs are
directly displayed so that 2D Progressive, 3D
Progressive and Film Mode cannot be se-
lected. These modes can be selected in in-
terlace signals other than 1080
I.•In NTSC or PAL60Hz, even if the 3D Progres-
sive mode has been set, the three-two pull
down enhancement will be enabled automati-
cally when the film source has been entered.
•In PAL50Hz or SECAM, the two-two pull down
enhancement will be enabled only in the Film
Mode, when the film source has been entered.
Description
Useful to display fast-moving
images such as sports and
action films. This mode
optimizes the image in a
displayed frame.
Useful to display relatively
slow-moving images such as
drama and documentary
more clearly.
This mode optimizes the
image by estimating the
movement of a number of
preceding and succeeding
frames.
Reproduces the image of film
source* clearly. Displays the
optimized image of film
transformed with three-two
pull down (NTSC and
PAL60Hz) or two-two pull
down (PAL50Hz and
SECAM) enhancement to
progressive mode images.
Selected Item
(2D Progressive)
(3D Progressive)
(Film Mode)
XV_Z12000_E_US_p42_60.p6503.9.24, 2:02 PM 49