Sharp Xr 30s Projector User Manual

MULTIMEDIA PROJECTOR
MODEL
XR-40X
XR-30X
XR-30S
OPERATION MANUAL
Introduction Quick StartSetupConnections Basic
Operation Useful
Features
Appendix 

ii
IMPORTANT
•For your assistance in reporting the loss
or theft of your Projector, please record
the Model and Serial Number located on
the bottom of the projector and retain this
information.
• Before recycling the packaging, please
ensure that you have checked the con-
tents of the carton thoroughly against the
list of “Supplied accessories” on page  10.Model No.:
Serial No.: 

iii
SPECIAL NOTE FOR USERS IN THE U.K.
The mains lead of this product is fitted with a non-rewireable (moulded) plug incorporat-
ing a 10A fuse. Should the fuse need to be replaced, a BSI or ASTA approved BS 1362
fuse marked 
 or  and of the same rating as above, which is also indicated on the pin
face of the plug, must be used.
Always refit the fuse cover after replacing the fuse. Never use the plug without the fuse
cover fitted.
In the unlikely event of the socket outlet in your home not being compat\...

iv
The supplied CD-ROM contains operation instructions in English, German, French,
Swedish, Spanish, Italian, Dutch, Portuguese, Chinese and Korean. Carefully read
through the operation instructions before operating the projector.
Die mitgelieferte CD-ROM enthält Bedienungsanleitungen in Englisch, Deutsch, Franzö\
sisch,
Schwedisch, Spanisch, Italienisch, Niederländisch, Portugiesisch, Chinesisch und Koreanisch.
Bitte lesen Sie die Bedienungsanleitung vor der Verwendung des Projektors sorgfältig durch....

1
IntroductionBefore using the projector, please read this operation manual carefully.
There are two important reasons for prompt warranty registration of your new SHARP
Projector, using the REGISTRATION CARD packed with the projector.
1. WARRANTY
This is to assure that you immediately receive the full benefit of the parts, service
and labor warranty applicable to your purchase.
2. CONSUMER PRODUCT SAFETY ACT
To ensure that you will promptly receive any safety notification of inspection,
modification, or...

2
Caution Concerning Lamp Replacement
See “Replacing the Lamp” on page 50 .
PRODUCT DISPOSAL
This projector utilizes tin-lead solder, and a pressurized lamp containing a small amount of
mercury. Disposal of these materials may be regulated due to environmental considerations.
For disposal or recycling information, please contact your local authorities or, if you are
located in the United States of America, the Electronic Industries Alliance: www.eiae.org .
This SHARP projector uses a DLP® chip.  This...

3
Introduction
37
Useful
Features
Using the Menu Screen
Menu Selections (Adjustments)
Example: Adjusting “Bright”.• This operation can also be performed by using the buttons on the projector.Press  MENU/HELP .•The “Picture” menu screen for the se-
lected input mode is displayed.Example: “Picture” screen menu for COMPUTER (RGB) input
Press Q or  O and select “Picture”
to adjust.
1
2
Menu item
Picture Mode
Contrast 0 0
0
0
0BrightRedBlue1CLR TempBright Boost
Lamp Setting Standard
Bright
Reset
SEL./ADJ....

4
Contents
Preparing
Introduction
How to Read this Operation Manual.... 3
Contents ............................................... 4
IMPORTANT SAFEGU ARDS............... 6
How to Access the PDF Operation Manuals .............................................. 9
Accessories ........................................ 10
Pa rt Names and  Functions................. 11
Inserting the Batteries .......................... 14
Usable Range ...................................... 15
Quick Start
Quick...

5
Introduction
Reference
Appendix
Maintenance....................................... 47
Maintenance Indicators ...................... 48
Regarding the Lamp ........................... 50
Lamp..................................................... 50
Caution Concerning the Lamp ............ 50
Replacing the Lamp ............................. 50
Removing and Installing
the Lamp Unit .................................... 51
Resetting the Lamp Timer .................... 52
Connecting Pin Assignments...

6
1. Read InstructionsAll the safety and operating instructions should
be read before the product is operated.
2. Retain InstructionsThe safety and operating instructions should be
retained for future reference.
3. Heed WarningsAll warnings on the product and in the operating
instructions should be adhered to.
4. Follow InstructionsAll operating and use instructions should be
followed.
5. CleaningUnplug this product from the wall outlet before
cleaning. Do not use liquid cleaners or aerosol
cleaners. Use...