Sharp Xg Ph70x Projector User Manual

Basic Operation
-39
Using the Adjustment Feet
•When the position of the projected image cannot be adjusted with the len\
s shift function, use the adjustment
feet to adjust the projected angle.
• The height of the projector can be adjusted using the adjustment feet when the screen is located higher than
the projector, the screen is inclined or when the installation site is slightly incli\
ned.
• Install the projector so that it is as perpendicular to the screen as possible.
1While lifting the projector,...

-40
Note
•After you have pressed the FOCUS but-
tons or the ZOOM buttons on the remote
control or the projector, you can display the
test pattern by pressing the ENTER but-
ton. The test pattern is useful for making
more accurate adjustments.
• For fine adjustments, when pressing the H
& V LENS SHIFT buttons, the FOCUS but-
tons or the ZOOM buttons, the projected
image moves a small amount toward the
desired direction for approximately one
second. Hold down the buttons to move the
projected image...

Basic Operation
-41
ENTER button
KEYSTONE 
button
UNDO button
Adjustment
button 
(' /" /\ /| ) 
Mouse/adjustment 
button ('/"/\/|)
ENTER button
UNDO button
KEYSTONE
b
utton
For correcting an image desig-
nating the corner of the pro-
jected image
F or correcting an image desig-
nating the horizontal or vertical
axes
F or correcting the image dis-
tortion which cannot be cor-
rected with “H & V KEY-
STONE”.
*Only when “H & V KEY-
STONE” is set to the values
other than “0”, “IMAGE
RESIZING”...

-42
Geometric Adjustment
Upper Left Upper Right Lower RightLower Left
GEOMETRIC ADJUSTMENT
1Press  on the projector or
 on the remote control re-
peatedly until “GEOMETRIC
ADJUSTMENT” is displayed.
2Press the buttons below to ad-
just the position, size or focus
of the projected image.
• Match screen’s four sides to green
test pattern.
• Pressing 
'
' '
'
' , 
"
" "
"
" , 
\
\ \
\
\  or 
|
| |
|
|  on the projector
or 
  on the remote control allows you
to shift...

Basic Operation
-43
Vertical Keystone Correction
(Adjustment with 
'  / ")
Horizontal Keystone Correction 
(Adjustment with 
\ /  |)
▼ On-screen Display
H & V KEYSTONE
1Press  on the projector or
 on the remote control re-
peatedly until “H & V KEY-
STONE” is displayed.
• When the correction has already been
made with “GEOMETRIC ADJUST-
MENT”, the confirmation message for
resetting the correction before “H & V
KEYSTONE” is displayed, and then re-
set.
2Press  ' or  " to parallelize the...

-44
Image Projection
IMAGE RESIZING
(Adjustment with 
' / "  / \ /  |)5Press  ', " , \  or  | to correct
the image distortion.
6Press   or  to set the po-
sition. 

Basic Operation
-45
Switching the Input
Mode
Select the appropriate input mode for the con-
nected equipment.
Press  ,  ,  ,  or  on
the remote control to select the input
mode.
•
• •
•
• When pressing  on the projector, the
input mode switches in order of :
INPUT 1 INPUT 2 INPUT 3
•
• •
•
• When pressing  on the projector, the
input mode switches between “INPUT 4” and
“INPUT 5”.
Note
• When no signal is received, “NO SIGNAL”
will be displayed. When non-supported sig-
nal is received, “NOT REG.” is...

-46
"On-screen Display
Volume 
b uttons
×1 ×4 ×9 ×16 ×36 ×64×2×3
" On-screen Display
Adjusting the Volume
Press 
\
\ \
\
\ /
|
| |
|
|  on the projector or   on the
remote control to adjust the volume.
Note
• Pressing  or  \ will lower the volume.
Pressing 
 or  | will raise the volume.
Turning Off the Sound
Temporarily
Press  on the remote control to
temporarily turn off the sound.
Note
• Pressing  again will turn the sound
back on.
Displaying an Enlarged
Portion of an Image
Graphs, tables and...

Basic Operation
-47
Freezing a Moving
Image
1Press  on the remote control.
• The projected image is frozen.
2Press  a gain to return to the
moving image from the currently
connected equipment.
Selecting the Picture
Mode
Y ou can select the suitable picture mode for the
projected image, such as movie or video game.
Press  on the remote control.
• When pressing , the picture mode
changes in order of
Note
• Press  to return to the “STANDARD”
mode.
• This function can also be accessed from the
OSD menu (see...

-48
Resize Mode
Press  on the remote control.
•Pressing  changes the display as shown.
• To  return to the standard image, press 
 while
“ RESIZE ” is displayed on the screen.
• This function can also be accessed from the OSD
menu (see page  74).
This function allows you to modify or customize the resize mode to enhance the input image. Depend-
ing on the input signal, you can choose a desired image.
COMPUTERRESIZE button
Mouse/adjustment button 
(
' /" /\ /| )
UNDO button
Image Projection...