Sharp Xg Ph70x N Projector User Manual

							Basic Operation
-39
Using the Adjustment Feet
•When the position of the projected image cannot be adjusted with the len\
s shift function, use the adjustment
feet to adjust the projected angle.
• The height of the projector can be adjusted using the adjustment feet when the screen is located higher than
the projector, the screen is inclined or when the installation site is slightly incli\
ned.
• Install the projector so that it is as perpendicular to the screen as possible.
1While lifting the projector, rotate
the adjustment feet.
• The projector is adjustable up to approxi-
mately 9 degrees.
2Lower the projector, and then ro-
tate the adjustment feet for the
fine adjustment.
•When lowering the projector, be careful
not to get your fingers caught in the area
between the adjustment feet and the
projector.
Adjustment feet 
Up Up
Down Down
ENTER button
Adjustment button 
( ' /" /\ /| ) H & V LENS SHIFT 
button
Mouse/adjustment 
button 
(' /" /\ /| ) 
ENTER button 
H & V LENS SHIFT 
button
1Press  
on the projector or
 on the remote control.
• Pressing  on the projector or 
on the remote control displays the test
pattern. Checking the test pattern is use-
ful for more accurate adjustment.
2Press  ', " , \  or  | on the pro-
jector or the remote control to
adjust the image position.
▼ On-screen Display 
						

							-40
Note
•After you have pressed the FOCUS but-
tons or the ZOOM buttons on the remote
control or the projector, you can display the
test pattern by pressing the ENTER but-
ton. The test pattern is useful for making
more accurate adjustments.
• For fine adjustments, when pressing the H
& V LENS SHIFT buttons, the FOCUS but-
tons or the ZOOM buttons, the projected
image moves a small amount toward the
desired direction for approximately one
second. Hold down the buttons to move the
projected image quickly.
Adjusting the Focus
Press   on the projector or  on
the remote control to adjust the fo-
cus.
Adjusting the Projected Image Size
Press   on the projector or  on
the remote control to adjust the pro-
jected image size.
ZOOM button
FOCUS button
ZOOM 
b uttons FOCUS buttons
Image Projection
▼
On-screen Display
▼ On-screen Display 
						

							Basic Operation
-41
ENTER button
KEYSTONE 
button
UNDO button
Adjustment
button 
(' /" /\ /| ) 
Mouse/adjustment 
button ('/"/\/|)
ENTER button
UNDO button
KEYSTONE
b
utton
For correcting an image desig-
nating the corner of the pro-
jected image
F or correcting an image desig-
nating the horizontal or vertical
axes
F or correcting the image dis-
tortion which cannot be cor-
rected with “H & V KEY-
STONE”.
*Only when “H & V KEY-
STONE” is set to the values
other than “0”, “IMAGE
RESIZING” can be adjusted.
(This function cannot be used when correcting with “GEO-
METRIC ADJUSTMENT”.)
GEOMETRIC
ADJUSTMENT
H & V KEYSTONE
IMAGE RESIZING
↑
↑
Selecting the Type of the
Correction
Select the type of the keystone correction.
Press 
  on the projector or  on the
remote control.
• “GEOMETRIC ADJUSTMENT” will be dis-
played.
• Each time 
 or  is pressed, the display
toggles as follows:
GEOMETRIC →H & V KEYSTONE
ADJUSTMENT
The display ←IMAGE RESIZING *
disappears.
Correcting Trapezoidal Distortion
When the image is projected either from the top or from the bottom towards the screen at an angle, the image
becomes distorted trapezoidally.
The function for correcting trapezoidal distortion is called  Keystone Correction .
There are the two types of the Keystone Correction.
1) “GEOMETRIC ADJUSTMENT” for correcting an image designating the corner of the projected im-
age
2) “H & V KEYSTONE” for designating the correction of the horizontal and vertical axes 
						

							-42
Geometric Adjustment
Upper Left Upper Right Lower RightLower Left
GEOMETRIC ADJUSTMENT
1Press  on the projector or
 on the remote control re-
peatedly until “GEOMETRIC
ADJUSTMENT” is displayed.
2Press the buttons below to ad-
just the position, size or focus
of the projected image.
• Match screen’s four sides to green
test pattern.
• Pressing 
'
' '
'
' , 
"
" "
"
" , 
\
\ \
\
\  or 
|
| |
|
|  on the projector
or 
  on the remote control allows you
to shift the lens.
• Pressing 
 on the projector or  on
the remote control allows you to adjust
the projected image size.
• Pressing 
 on the projector or  on
the remote control allows you to adjust
the focus.
3Press   on the projector or 
on the remote control.
4Press  ', " , \  or  | to move the
position for the upper left of the
image.
• Move the upper left of the yellow frame
onto the upper left of the screen.
5Press  or  to set the posi-
tion.
6Repeat the same procedure with the
positions for the upper right, lower
right and lower left of the image.
• At this time, pressing  on the pro-
jector or 
on the remote control re-
turns to the previous screen.
• Before correcting the upper left of the
image, pressing 
 or returns
to the reset confirmation screen.
• When the position of the lower left is
set, the correction is made and the
display disappears.
Image Projection
▼ On-screen Display 
						

							Basic Operation
-43
Vertical Keystone Correction
(Adjustment with 
'  / ")
Horizontal Keystone Correction 
(Adjustment with 
\ /  |)
▼ On-screen Display
H & V KEYSTONE
1Press  on the projector or
 on the remote control re-
peatedly until “H & V KEY-
STONE” is displayed.
• When the correction has already been
made with “GEOMETRIC ADJUST-
MENT”, the confirmation message for
resetting the correction before “H & V
KEYSTONE” is displayed, and then re-
set.
2Press  ' or  " to parallelize the
left and right sides of the pro-
jected image.
3Press  \ or  |
 
   
 
  to parallelize the
upper and lower sides of the
projected image.
4Press   or  to display “IM-
A GE RESIZING”.
•Only when “H & V KEYSTONE” is set
to the values other than “0”, “IMAGE
RESIZING” works.
▼ On-screen Display 
						

							-44
Image Projection
IMAGE RESIZING
(Adjustment with 
' / "  / \ /  |)5Press  ', " , \  or  | to correct
the image distortion.
6Press   or  to set the po-
sition. 
						

							Basic Operation
-45
Switching the Input
Mode
Select the appropriate input mode for the con-
nected equipment.
Press  ,  ,  ,  or  on
the remote control to select the input
mode.
•
• •
•
• When pressing  on the projector, the
input mode switches in order of :
INPUT 1 INPUT 2 INPUT 3
•
• •
•
• When pressing  on the projector, the
input mode switches between “INPUT 4” and
“INPUT 5”.
Note
• When no signal is received, “NO SIGNAL”
will be displayed. When non-supported sig-
nal is received, “NOT REG.” is displayed.
• When “Auto Search” of the “Options (1)”
menu is set to “ON”, the input mode with
signal can automatically be detected and
displayed. (See page  78.)
• The input mode is not displayed when “OSD
Display” of the “Options (1)” menu is set to
“Level A” or “Level B”. (See page  75 .)
About the Input mode
" On-screen Display of Input Mode (Example)
Using RGB
Using
component
INPUT 1/2/3 mode
INPUT 5 mode
   Using S-video
INPUT 4 mode
   Using video
Used for projecting images from
equipment that sends RGB signals
or component signals connected to
the 
INPUT 1 or 2  terminals.
Used for projecting images
from equipment connected to
the INPUT 3 terminal.
Used for projecting images
from equipment connected to
the INPUT 4 terminal.
Used for projecting images
from equipment connected to
the INPUT 5 terminal.
INPUT 1/
INPUT 2
(RGB/
component)
INPUT 3
(digital PC
RGB/digital
PC compo-
nent/digital
video RGB/
digital video
component)
INPUT 4
(video)
INPUT 5
(S-video)
INPUT buttons
/ ///
 When pressing .
 When pressing .
When “Auto Search” is set to “ON”
• Pressing 
 or  once displays the
current input mode.
• Pressing 
 or  again starts the
automatic input search.
* The “INPUT 3”
display is an
example. (When
“Signal Type” is set
to “D. PC RGB”)
* The “INPUT 3”
display is an
example. (When
“Signal Type” is set
to “D. PC Comp.”) 
						

							-46
"On-screen Display
Volume 
b uttons
×1 ×4 ×9 ×16 ×36 ×64×2×3
" On-screen Display
Adjusting the Volume
Press 
\
\ \
\
\ /
|
| |
|
|  on the projector or   on the
remote control to adjust the volume.
Note
• Pressing  or  \ will lower the volume.
Pressing 
 or  | will raise the volume.
Turning Off the Sound
Temporarily
Press  on the remote control to
temporarily turn off the sound.
Note
• Pressing  again will turn the sound
back on.
Displaying an Enlarged
Portion of an Image
Graphs, tables and other portions of projected
images can be enlarged. This is helpful when
providing more detailed explanations.
1Press   on the remote control.
• Enlarges the image.
• Pressing 
 or  enlarges or reduces
the projected image.
Note
• You can change the location of the en-
larged image using  ', " , \  and  |.
MUTE button
Mouse/adjustment 
button ( '/" /\ /| )
ENLARGE
(enlarge/reduce)
b uttons
UNDO 
button
RESIZE 
b utton
/
Image Projection 
						

							Basic Operation
-47
Freezing a Moving
Image
1Press  on the remote control.
• The projected image is frozen.
2Press  a gain to return to the
moving image from the currently
connected equipment.
Selecting the Picture
Mode
Y ou can select the suitable picture mode for the
projected image, such as movie or video game.
Press  on the remote control.
• When pressing , the picture mode
changes in order of
Note
• Press  to return to the “STANDARD”
mode.
• This function can also be accessed from the
OSD menu (see page  60).
STANDARDPRESENTATIONCINEMACUSTOM
FREEZE button
PICTURE MODE
button
UNDO button
2Press  on the remote control
to cancel the operation.
• The magnification then returns to  ×1.
Note
In the following cases, the image will
return to the normal size ( ×1).
• When switching the input mode.
• When 
 has been pressed.
• When the input signal is changed.
•
When the input signal resolution and re-
fresh rate (vertical frequency) change.
• When  has been pressed. 
						

							-48
Resize Mode
Press  on the remote control.
•Pressing  changes the display as shown.
• To  return to the standard image, press 
 while
“ RESIZE ” is displayed on the screen.
• This function can also be accessed from the OSD
menu (see page  74).
This function allows you to modify or customize the resize mode to enhance the input image. Depend-
ing on the input signal, you can choose a desired image.
COMPUTERRESIZE button
Mouse/adjustment button 
(
' /" /\ /| )
UNDO button
Image Projection
STRETCHFor 4:3 screen For 16:9 screen
Input signalImage type
NORMAL FULL BORDER
4:3 aspect ratio
5:4 aspect ratio
16:10 aspect ratio 16:9 aspect ratio
: 
Cutout area on which images cannot be projected
:  Area where the signals are off screen
*The Digital Shift function can be used for these images.
Computer
Resolution lower than XGA
XGA
SXGA (1280  × 960)
Resolution
higher than SXGA
SXGA (1280  × 1024)
1280  × 720
Select “Normal”
1280  × 768
1280  × 800
1360 
× 768
1366  × 768
DOT BY DOT
*
* *
*
*
*
4:3 aspect ratio
Other aspect ratios
SVGA (800  × 600)XGA (1024  × 768)SXGA (1280  × 960)SXGA+ (1400  × 1050)SXGA (1280  × 1024)1280  × 7201360  × 7681366  × 7681280  × 768
1280  × 800
1024  × 768
968  × 7681024  × 5761024  × 5781024  × 5761024  × 614
1024  × 640
1024  × 768
768  × 576
—720 × 576
—
960  × 576
922  × 576
1024  × 576
—
1024  × 576
NORMAL FULL
BORDER STRETCH
DOT BY DOT
800 × 6001024  × 7681280  × 9601400  × 10501280  × 10241280  × 7201360  × 7681366  × 7681280  × 768
1280  × 800