Sharp Xg Ph70x N Projector Quickstart Guide

							-31
Controlling the Projector Using RS-232C or Telnet
View Setting Detail List
([V]View All Setting)
1
1 1
1
1 Enter “v” and press the “Enter” key.
Display all setting values(*).
Enter number or symbol of item to be selected on the SETUP MENU. When setting, input the
details to be set. Setting is carried out one item at a time, and saved at the end.
▼SETUP MENU
---------------------------------SETUP MENU-----------------------------\
---
[1]IP Address [2]Subnet Mask [3]Default Gateway
[4]User Name [5]Password
[6]RS-232C Baud Rate [7]Projector Name [8]DHCP Client[A]Advanced Setup [D]Disconnect All
[V]View All Setting [S]Save & Quit [Q]Quit Unchanged
setup>v
Model Name : XX-XXXX
Projector Name : XX-XXXX
MAC Address : 08:00:1F:00:00:00
DHCP Client : Off
IP Address : 192.168.150.2
Subnet Mask : 255.255.255.0
Default Gateway : Not Used
RS-232 Baud Rate : 9600 bps
Password : Not Required
**********(Advanced Status)**********
Data Port : 10002
Accept IP Address : Accept All
A uto Logout Time : 5 minutes
Search Port : 5006
1
*
Set Items
Example: When setting IP Address (change from
192.168.150.2 to 192.168.150.3)
1
1 1
1
1 Enter “1” (number of item to be set), and press
the “Enter”  key.
Display current IP address (*1).
2
2 2
2
2 Enter IP address to be set and press the “En-
ter” key.
Display IP address after change (*2).
3
3 3
3
3 Enter “v” and press the “Enter” key to verify
setting detail list.
IP address is being changed (*3).
Note
•Ve rification of setting detail list can be omitted.
• Setting details are not effective until they have
been saved. (Page 
32 )
• If an invalid number is entered, an error message
(“Parameter Error!”) will be displayed.
▼
SETUP MENU
---------------------------------SETUP MENU-----------------------------\
---
[1]IP Address [2]Subnet Mask [3]Default Gateway
[4]User Name [5]Password
[6]RS-232C Baud Rate [7]Projector Name
[8]DHCP Client[A]Advanced Setup [D]Disconnect All
[V]View All Setting [S]Save & Quit [Q]Quit Unchanged
setup>1
IP Address : 192.168.150.2
Please Enter : 192.168.150.3
(change) —> 192.168.150.3
---------------------------------SETUP MENU-----------------------------\
---
[1]IP Address [2]Subnet Mask [3]Default Gateway
[4]User Name [5]Password
[6]RS-232C Baud Rate [7]Projector Name
[8]DHCP Client[A]Advanced Setup [D]Disconnect All
[V]View All Setting [S]Save & Quit [Q]Quit Unchanged
setup>v
Model Name : XX-XXXX
Projector Name : XX-XXXX
MAC Address : 08:00:1F:00:00:00
DHCP Client : Off
IP Address : 192.168.150.3
Subnet Mask : 255.255.255.0
Default Gateway : Not Used
RS-232C Baud Rate : 9600 bps
Password : Not Required
**********(Advanced Status)**********
Data Port : 10002
Accept IP Address : Accept All
A uto Logout Time : 5 minutes
Search Port : 5006
1
2
3 *1
*2
*3 
						

							-32
Controlling the Projector Using RS-232C or Telnet
Save Settings and Quit
([S]Save & Quit)
Save set values and quit menu.1
1 1
1
1 Enter “s” and press the “Enter” key.
2
2 2
2
2 Enter “y” and press the “Enter” key.
▼
SETUP MENU
---------------------------------SETUP MENU-----------------------------\
---
[1]IP Address [2]Subnet Mask [3]Default Gateway
[4]User Name [5]Password
[6]RS-232C Baud Rate [7]Projector Name [8]DHCP Client[A]Advanced Setup [D]Disconnect All
[V]View All Setting [S]Save & Quit [Q]Quit Unchanged
setup>s
All Connection will be disconnect.
Continue(y/n)? y
Apply New setting...Done.
1
2
Quit without Saving Set-
tings ([Q]Quit Unchanged)
Quit menu without saving setting values.
1
1 1
1
1 Enter “q” and press the “Enter” key.
2
2 2
2
2 Enter “y” and press the “Enter” key.
▼
SETUP MENU
---------------------------------SETUP MENU-----------------------------\
---
[1]IP Address [2]Subnet Mask [3]Default Gateway
[4]User Name [5]Password
[6]RS-232C Baud Rate [7]Projector Name
[8]DHCP Client[A]Advanced Setup [D]Disconnect All
[V]View All Setting [S]Save & Quit [Q]Quit Unchanged
setup>q
Quit Without Saving(y/n)? y
Setting Unchanged.
1
2 
						

							-33
Controlling the Projector Using RS-232C or Telnet
IP Address Setting
([1]IP Address)
Setting of IP address.1
1 1
1
1 Enter “1” and press the “Enter” key.
2
2 2
2
2 Enter numerical value to be set and press the
“Enter” key.
Display IP address after change (*).
Subnet Mask Setting
([2]Subnet Mask)
Setting subnet mask.
1
1 1
1
1 Enter “2” and press the “Enter” key.
2
2 2
2
2 Enter numerical value to be set and press the
“Enter” key.
Display subnet mask after change (*).
The setting procedure for each item will be explained. For the basic procedure, please refer
to “Set Items” on page  31.
setup>1
IP Address :192.168.150.2
Please Enter :192.168.150.3
(change)      —>  192.168.150.31
2
*
setup>2
Subnet Mask :255.255.255.0
Please Enter :255.0.0.0
(change)      —>  255.0.0.01
2
*
Default Gateway Setting
([3]Default Gateway)
Setting default gateway.
1
1 1
1
1 Enter “3” and press the “Enter” key.
2
2 2
2
2 Enter numerical value to be set and press the
“Enter” key.
Display gateway address after change (*).
Note
•If the values for IP Address, Subnet Mask or Gate-
wa y of the projector have been changed via Telnet,
the computer cannot be connected to the projec-
tor  depending on  the computer’s network settings.
User Name Setting
([4]User Name)
Carrying out security protection using user name.
1
1 1
1
1 Enter “4” and press the “Enter” key.
2
2 2
2
2 Enter user name and press the “Enter” key.
Display set user name (*).
Note
•User name can be up to 8 characters.
• You can input the  characters below :
a-z, A-Z, 0-9, -, _
• In the def ault state, user name is not set.
setup>3
note: “0.0.0.0” means “Using no default gateway.”
Gateway Address :0.0.0.0
Please Enter :192.168.150.1
(change)          —>  192.168.150.11
2
*
setup>4
User Name :
Please Enter : XX-XXXX
(change)        —>   XX-XXXX1
2
* 
						

							-34
Controlling the Projector Using RS-232C or Telnet
Password Setting
([5]Password)
Carrying out security protection using password.1
1 1
1
1 Enter “5” and press the “Enter” key.
2
2 2
2
2 Enter password and press the “Enter” key.
Display set password (*).
Note
•Password can be up to 8 characters.
• You can input the  characters below :
a-z, A-Z, 0-9, -, _
• In the def ault state, the password is not set.
RS-232C Baud Rate Set-
ting ([6]RS-232C Baud Rate)
Setting of baud rate for RS-232C (COMPUTER and
PROJECTOR) terminals.
1
1 1
1
1 Enter “6” and press the “Enter” key.
2
2 2
2
2 Select and enter the number 0, 1 or 2 and
press the “Enter” key.
Display set baud rate (*).
Note
•Set the projector’s baud rate to the same rate as
that  used by the computer.
setup>5
Password :
Please Enter :  sharppj
(change)        —>   sharppj1
2
*
setup>6
note: It sets both RS-232C (COMPUTER) and RS-232C (PROJECTOR).
0 ...  9600 bps
1 ...  38400 bps
2 ... 115200 bps
Baud Rate Select[0-2] :2
RS-232C Baud Rate : 115200 bps1
2*
Projector Name Setting
([7]Projector Name)
It is possible to assign a projector name.
1
1 1
1
1 Enter “7” and press the “Enter” key.
2
2 2
2
2 Enter projector name.
Display set projector name (*).
Note
•Projector name can be up to 12 characters.
• You can input the  characters below :
A-Z, 0-9, -, _, (, ),  space
(When “a-z” are input, they are converted to “A-Z”
automatically.)
• It is the  same as the name which can be con-
firmed or  set, using RS-232C commands “PJN0”,
“PJN1”, “PJN2” and “PJN3”.
DHCP Client Setting
([8]DHCP Client)
Setting DHCP Client to “On” or “Off ”.
Example: When setting DHCP Client to “On”
1
1 1
1
1 Enter “8” and press the “Enter” key.
2
2 2
2
2 Enter “1” and press the “Enter” key.
Display the obtained values (*).
setup>7
Projector Name : XX-XXXX
Please Enter : MY XX-XXXX
(change)       —>   MY XX-XXXX1
2
*
setup>8
note: It sets DHCP Client.
0 ... Off
1 ... On
DHCP Select[0-1] : 1
DHCP Client : On
Success get data from DHCP server.
[MAC Address      
 ] : [08:00:1F:00:00:00]
[IP Address           ] : [192.168.150.2]
[Subnet Mask        ] : [255.255.255.0]
[Default Gateway   ] : [0.0.0.0]
[DHCP IP Address] : [192.168.150.1]
1
2
* 
						

							-35
Controlling the Projector Using RS-232C or Telnet
Disconnecting All Connec-
tions ([D]Disconnect All)
It is possible to disconnect all the TCP/IP connec-
tions currently recognized by the projector. Even if
the COM Redirect port is fixed in the Busy status
due to a problem, it is possible to force the Ready
status back by carrying out this disconnection.1
1 1
1
1 Enter “d” and press the “Enter” key.
2
2 2
2
2 Enter “y” and press the “Enter” key.
Note
•If Disconnect All is performed, the connection to
the projector via network will be forcibly discon-
nected.
Entering ADVANCED
SETUP MENU
([A]Advanced Setup)
Enters ADVANCED SETUP MENU.
1
1 1
1
1 Enter “a” and press the “Enter” key.
Setting Auto Logout Time
(ADVANCED[1]Auto Logout Time)
If there is no input after a fixed time, the projector
automatically disconnects network connection using
the Auto Logout function. It is possible to set the time
until the projector is automatically disconnected in
units of a minute (from 1 to 65535 minutes).
1
1 1
1
1 Enter “1” and press the “Enter” key.
2
2 2
2
2 Enter numerical value and press the “Enter” key.
Display set numerical value (*).
Note
•If the set value is made 0, the Auto Logout func-
tion is disabled.
•
If an invalid number is entered, an error message
(“Parameter Error!”) will be displayed  and the
screen returns to the ADVANCED SETUP MENU.
Data Port Setting
(ADVANCED[2]Data Port)
Setting of TCP port number. It is possible to set in
the range of 1025 to 65535.
1
1 1
1
1 Enter “2” and press the “Enter” key.
2
2 2
2
2 Enter numerical value and press the “Enter” key.
Display set numerical value (*).
Note
•Set according to need. Normally, use with the
factory default setting.
setup>d
Disconnect All  Connections(y/n)?y
Now Disconnecting...1
2
setup>a
******************** ADVANCED SETUP MENU ***********************
[1]Auto Logout Time [2]Data Port
[5]Network Ping Test
[6]Accept IP Addr(1) [7]Accept IP Addr(2) [8]Accept IP Addr(3)
[9]Accept All IP Addr [0]Search Port
[!]Restore Default Setting
[Q]Return to Main Menu
advanced>1
advanced>1
V alid range : 0 to 65535 (minute)
note: if you enter “0”, auto logout function will be disable.
Auto Logout Time : 5
Please Enter :15
(change)        —>  151
2
*
advanced>2
V alid range :1025 to 65535
Data Port :10002
Please Enter :10005
(change)          —>  100051
2
* 
						

							-36
Controlling the Projector Using RS-232C or Telnet
Carrying out Network Ping
Test
(ADVANCED[5]Network Ping Test)
It is possible to confirm that a network connection
between the projector and a computer etc. is work-
ing normally.1
1 1
1
1 Enter “5” and press the “Enter” key.
2
2 2
2
2 Enter IP address of device to be tested and
press the “Enter” key.
Display entered IP address (*1).
Display test result (*2).
Note
•If the “Enter” key is pressed without entering an
IP address, the Ping destination IP address used
previously is  entered.
• If there is a fault with the connection, “Error: No
answer” is displayed after a 5 second retry. In this
case, please confirm the settings for the projector
and the computer, and contact your network ad-
ministrator.
Setting of Accept IP Ad-
dress 
(ADVANCED[6]Accept IP
Addr(1) - [8]Accept IP Addr(3))
It is possible to improve security of the projector by
allowing connection from only a prescribed IP ad-
dress. It is possible to set up to three IP addresses
allowing connection to the projector.
1
1 1
1
1 Enter “6”, “7” or “8” and press the “Enter” key.
2
2 2
2
2 Enter numerical value and press the “Enter” key.
Display set numerical value (*).
Note
•To  invalidate the Accept IP Addr being currently
set, enter “0.0.0.0”.
• If there is one or more Accept IP Addr being set,
no connections are allowed from IP addresses
that are not yet set. They can be cancelled using
[9]Accept All IP Addr.
Accepting All IP Addresses
(ADVANCED[9]Accept All IP Addr)
Removes IP addresses set with “Accept IP Addr”.
1
1 1
1
1 Enter “9” and press the “Enter” key.
2
2 2
2
2 Enter “y” and press the “Enter” key.
Note
•At the point in time where “y” was entered, the
numerical values for Accept IP Addr(1)-(3) are
reset to “0.0.0.0”.
• If “n” is entered, setting is not altered.
advanced>5
Ping dest IP addr :192.168.150.1
Please Enter :192.168.150.152
(change)         —>  192.168.150.152
32 bytes from 192.168.150.152: icmp_seq = 1, time = 0 ms
32 bytes from 192.168.150.152: icmp_seq = 2, time = 0 ms
32 bytes from 192.168.150.152: icmp_seq = 3, time = 0 ms
32 bytes from 192.168.150.152: icmp_seq = 4, time = 0 ms1
2
*1
*2advanced>6
Accept IP Addr(1) : 0.0.0.0
Please Enter : 192.168.150.152
(change)         —>   192.168.150.1521
2
*
advanced>9
Accept All  IP Addresses(y/n)?  y1
2 
						

							-37
Controlling the Projector Using RS-232C or Telnet
Setting of Search Port
(ADVANCED[0]Search Port)
Sets the port number used when searching for the
projector from the network.1
1 1
1
1 Enter “0” and press the “Enter” key.
2
2 2
2
2 Enter numerical value and press the “Enter” key.
Display set numerical value (*).
Note
•Set according to need. Nor mally, use with the fac-
tory default setting.
Return to Default Settings
(ADVANCED[!]Restore Default
Setting)
Returns all menu setting values to the default state.
1
1 1
1
1 Enter “!” and press the “Enter” key.
2
2 2
2
2 Enter “y” and press the “Enter” key.
Note
•If the values for IP Address, Subnet Mask or Gate-
wa y of the projector have been  returned to the
default settings  via Telnet, the computer cannot
be connected to the projector  depending on the
computer’s network settings.
Return to Main Menu
(ADVANCED[Q]Return to Main Menu)
Returns to the main SETUP MENU.
1
1 1
1
1 Enter “q” and press the “Enter” key.
Returns to the SETUP MENU.
advanced>0
Please Enter Port Number for Search from Computer.
Valid range : 1025 to 65535
Search Port : 5006
Please Enter : 5004
(change)         —>   50041
2
*
advanced>!
Restore All Setting to Default(y/n)? y
— User Setting Initialized —1
2
advanced>q
---------------------------------SETUP MENU-----------------------------\
---
[1]IP Address [2]Subnet Mask [3]Default Gateway
[4]User Name [5]Password
[6]RS-232C Baud Rate [7]Projector Name [8]DHCP Client[A]Advanced Setup [D]Disconnect All
[V]View All Setting [S]Save & Quit [Q]Quit Unchanged
setup>
1 
						

							-38
Stack Projection
The stack projection allows you to increase the brightness of an image by stacking two
projectors and projecting same image simultaneously.
Info
•To  set up the stack projection, assign a projector as the master and the other projector a\
s the slave and
connect the projectors with commercially available LAN cables (UTP cable, Category 5, 
cross-over type).
In this way, you can control the both projectors with one remote control.
• The buttons below can control both the master and the slave at one time.
• ON button • AUTO SYNC button
• STANDBY button • RESIZE button
• BLACK SCREEN button • PICTURE MODE button
• INPUT 1 - 5 buttons • BREAK TIMER button
• MUTE button • FREEZE button
• VOLUME buttons
• In normal operation, the projector set as the slave cannot be controlled by the remote control.
Only while the remote control is connected to the projector with a ø3\
.5 mm minijack cable (commercially
av ailable or available as Sharp service part QCNWGA038WJPZ), the projector set as the slave can be
controlled by the remote control.
• Even while the projector is set as the slave, the buttons on the projector can be used. 
						

							-39
Stack Projection
Setting up the Stack Projection
Basic
This part shows an example for setting up the stack projection of a computer image with two projectors.
RGB cable
RGB
cable LAN cable
(cross-over type)
OUTPUT (FOR INPUT 1, 2) 
terminal
INPUT 1 terminal
INPUT 1 terminal
LAN terminal 
LAN terminal 
Computer
Projector 1: Master
Projector 2: Slave
Master
Set Inputs
ON
OFF
OFF
OFF
OFF ON
OFF
OFF
OFF
OFFINPUT1
INPUT2
INPUT3
INPUT4
INPUT5
Slave
Set Inputs
INPUT1
INPUT2
INPUT3
INPUT4
INPUT5
Projector 1 Projector 2
1Set the “Stack Setting” of the pro-
jector 1 to “Master”.
(See page  84 on the projector operation
manual.)
2Set the “Stack Setting” of the pro-
jector 2 to “Slave”.
(See page  84 on the projector operation
manual.)
3P erform “Pair Stack” of the both
projectors.
(See page  85 on the projector operation
manual.)
4Select inputs as specified in the
table below.
(See page  86 on the projector operation
manual.)
5T urn off the both projectors. 
						

							-40
Stack Projection
Video equipment
Distributor
RGB cable
5 BNC to 15-pin
D-sub cable
Composite video cable RGB
cable
LAN cable
(cross-over
type)
Projector 1:
Master
Projector 2: SlaveOUTPUT (FOR INPUT 1, 2)
terminal
INPUT 1 terminal
INPUT 1 terminal 
INPUT 2 terminals
 INPUT 4 terminal
INPUT 4 terminal
LAN terminal
LAN terminal
Computer
Computer
Master
Set Inputs
ON
ON
OFF
ON
OFF
ON
OFF
OFF
ON
OFFINPUT1
INPUT2
INPUT3
INPUT4
INPUT5
Slave
Set Inputs
INPUT1
INPUT2
INPUT3
INPUT4
INPUT5
Projector 1
Projector 2
6Connect the INPUT 1 terminal on
the projector 1 to the RGB output
terminal on the computer using the
RGB cable.
(See page  27 on the projector operation
manual.)
7Connect the OUTPUT (FOR INPUT
1, 2) terminal on the projector 1 to
the INPUT 1 terminal on the projec-
tor 2 using an RGB cable.
(See page  36 on the projector operation
manual.)
Note
• When connecting an RGB cable to the pro-
jector 2, use the input terminal that has
the same number as the projector 1. (IN-
PUT 1 terminal, in this case)
8Connect the LAN terminal on the
projector 1 to the LAN terminal on
the projector 2 using a commer-
cially available LAN cable (UTP
cable, Category 5, 
cross-over type).
9T urn on the projectors first, then
turn on the computer.
Application
When inputting multiple image sources, refer to the example below.