Sharp Xg Ph50x Nl Projector User Manual

							Introduction
-17
Using the Remote Control
Inserting the Batteries
The batteries (two R-6 batteries (“AA” size,
UM/SUM-3, HP-7 or similar)) are supplied in
the package.
1Press the tab and lift open the battery
cover in the direction of the arrow
.
2Insert the batteries.
•Insert the batteries making sure the po-
larities correctly match the 
 and 
marks inside the battery compartment.
3Insert the tabs on the end of the
battery cover into their slots and
press the cover into position.
Incorrect use of the batteries may cause them to leak or explode. Please follow the precautions below.
 Caution
• Insert the batteries making sure the polarities correctly match the  and  marks inside the battery compartment.
• Batteries of different types have different properties, therefore do not mix batteries of different types.
• Do not mix new and old batteries.
This may shorten the life of new batteries or may cause old batteries to\
 leak.
• Remove the batteries from the remote control once they have run out, as \
leaving them in can cause them to leak.
Battery fluid from leaked batteries is harmful to skin, therefore ensure\
 to first wipe them and then remove them
using a cloth.
• The batteries included with this projector may run down in a short perio\
d, depending on how they are kept.
Ensure to replace them as soon as possible with new batteries.
• Remove the batteries from the remote control if you will not be using th\
e remote control for a long time.
Usable Range
The remote control can be used to control
the projector within the ranges shown in the
illustration.
Note
•The signal from the remote control can be re-
flected off a screen for easy operation. How-
ev er, the effective distance of the signal may
differ depending on the screen material.
When using the remote control:
• Ensure not to drop, expose to moisture or high
temperature.
• The remote control may malfunction under a
fluorescent lamp. In this case, move the pro-
jector away from the fluorescent lamp.
Front View
Rear View
Remote control
signal transmitters Remote control sensor
Remote control
30 °
30
°30
°23 (7 m)
Remote control sensor
Remote control
signal transmitters
Remote control
30 °
30°
30
°23 (7 m) 
						

							-18
Using the Remote Control
Using the Remote Control with a Signal Cable
When the signals from the remote control cannot be reached due to the ra\
nge or positioning of the projec-
tor, you can connect the remote control to the projector with a ø3.5 mm minijack cable (commercially avail-
able or available as Sharp service part QCNWGA038WJPZ).
Switching the Remote Control Mode
The remote control has two functions. One is projector control and the o\
ther is wireless computer mouse.
Slide the ADJ./MOUSE switch on the remote control to other side compatible to the desired usage.
Info
•When using the remote control as the wireless computer mouse, connect th\
e supplied remote mouse
receiver to the computer. (See page  19.)
Side viewRemote control
To  WIRED R/C JACK
To  WIRED REMOTE terminal
ø3.5 mm minijack cable (commercially available or 
av ailable as Sharp service part QCNWGA038WJPZ)
ADJ.
MOUSEADJ.
MOUSE
Projector control Wireless computer mouse 
						

							Introduction
-19
Using the Remote Control as a Wireless Computer Mouse
When connecting the supplied remote
mouse receiver to the computer, you can use
the remote control as the wireless computer
mouse.
1Connect the supplied remote
mouse receiver to the USB termi-
nal on the computer.
2Slide the ADJ./MOUSE
switch on the remote con-
trol to the MOUSE position.
3Use the mouse function.
•Point the remote control at the remote
mouse receiver.
■ When moving the cursor
Press  '/" /\ /| .
■ When left-clicking
Press 
.
■ When right-clicking
Press 
.
■ When your computer supports only a
one-click mouse (such as Macintosh
®)
Press 
  or .  ( and  have com-
mon function.)
ADJ.
MOUSE
Remote mouse
receiver
Supplied
accessory
Note
• This function only works with the Microsoft®
Windows® OS and Mac OS®.  However, this
function does not work with the following op-
eration systems that do not support USB.
•V ersions earlier than Windows® 95.
•V ersions earlier than Windows® NT4.0.
•V ersions earlier than Mac OS® 8.5.
• Confirm that the computer recognizes the USB
connection.
• While the remote control is connected to the
projector with a signal cable, you cannot use
the wireless computer mouse function.
Computer
To USB terminal
Remote mouse receiver
Mouse/adjustment button ( '/" /\ /| )
ADJ./MOUSE switch
R-click button
L-click button 
						

							-20
Quick Start
Page 22
1.Place the projector facing a screen
Pages 27, 37
Page 37
Press  on the projector or  on the remote control.
This section shows the basic operation (projector connecting with the c\
omputer). For details, see the page
described below for each step.
Setup and Projection
In this section, connection of the projector and the computer is explain\
ed using one example.
2.Connect the projector to the computer and plug the power
cord into the AC socket of the projector
3.Remove the lens cap and turn the projector on
When connecting equipment other than the computer,
see pages 
30—36 .
5 
4
6
6
7
6
3 4
83
4
6
7
46
8
5 
						

							Quick Start
-21
Pages 38, 39
4.Adjust the angle
5.Adjust the focus and the zoom
Page 40
8.Turn the power off
Page 37
7.Select the input mode
Page 45
1
1 1
1
1 Press  on the projector or  on the remote control to adjust the focus.
2
2 2
2
2 Press 
 on the projector or  on the remote control to adjust the zoom.
Press  on the projector or  on the remote control to select the “INPUT 1” mode.
•
• •
•
• When pressing  on the projector, input mode switches in order of : INPUT 1 INPUT 2 INPUT 3.
Pressing 
 on the projector switches between “INPUT 4” and “INPUT 5”.
•
• •
•
• When using the remote control, press 
//// to switch the input mode.
Press  on the projector or  on the remote control. While the confirmation message is displayed,
press 
 or  again.
•
• •
•
• Disconnect the power cord from the AC outlet after the cooling fan stops.
Adjust the projector angle
•
• •
•
•
Shift the lens horizontally and vertically.
1
1 1
1
1Press  on the projector or  on the
remote control.
2
2 2
2
2Press ' , " , \  or  | on the projector or the
remote control.
•
• •
•
•Adjust the projector angle by rotating the adjust-
ment feet.
6.Correcting the image distortion due to the projection angle
1
1 1
1
1 Press  on the projector or  on the
remote control.
2
2 2
2
2 Press 
 on the projector or  on the
remote control.
3
3 3
3
3 Press  ', " , \  or  |  to move the position for
the upper left of the image.
Page 41
4
4 4
4
4 Press  or  to set the position.
5
5 5
5
5 Repeat the same procedure with the positions
for the upper right, lower right and lower left
of the image.
•
• •
•
•
When the position of the lower left is set, the
correction is made and the display disappears.
"
" "
"
"  On-screen Display (RGB)
"
" "
"
"  On-screen Display 
						

							-22
Setting Up the Projector
Position the projector perpendicular to the screen with the projector’s feet flat and level to achieve an
optimal image.
Note
• The projector lens should be centered in the middle of the screen. If th\
e horizontal line passing through
the lens center is not perpendicular to the screen, the image will be distorted, making viewing difficult.
• For an optimal image, position the screen so that it is not in direct su\
nlight or room light. Light falling
directly on the screen washes out the colors, making viewing difficult. Close the curtains and dim the lights
when setting up the projector in a sunny or bright room.
Standard Setup (Front Projection)
■ Place the projector at the required distance from the screen according t\
o the desired picture size. (For
details, refer to “SETUP GUIDE” contained on the supplied CD-ROM.)\
Setting Up the Projector
Indication of the Projection Image Size and Projection Distance
For details, refer to “SETUP GUIDE” contained on the supplied CD-R\
OM.
Example : NORMAL Mode (4:3) for the standard zoom lens (AN-PH30EZ)
300
200
100 84
60
Picture Size240
×180
160×120
80×6067×5048×36
Projection Distance
36–44(11.0 m – 13.4 m)24–294
(7.3 m – 8.9 m)12–148
(3.7 m – 4.5 m)101–124
(3.1 m – 3.8 m)72–810
(2.2 m – 2.7 m) 
						

							Setup
-23
Projecting a Reversed Image
Projection from behind the Screen
■Place a translucent screen between the projector and the audience.
■ Reverse the image by setting “Rear” in the “PRJ Mode” menu. \
(See page 
84 .)
Projection Using a Mirror
■Place a mirror (normal flat type) in front of the lens.
■ When the translucent screen is placed between the mirror and audience, s\
et to “Front” in the “PRJ Mode”
menu. (See page 
84 .)
■ When the mirror is placed on the audience side, set to “Rear” in t\
he “PRJ Mode” menu. (See page 
84 .)
Info
•When using a mirror, ensure that both the projector and the mirror are carefully placed so \
the projected
light does not shine into the eyes of the audience.
Ceiling-mount Setup
■ It is recommended that you use the optional Sharp ceiling-mount
bracket for this installation.
Before mounting the projector, contact your nearest Sharp Au-
thorized Projector Dealer or Service Center to obtain the recom-
mended ceiling-mount bracket (sold separately).
•AN-PHCM20 ceiling-mount bracket, its AN-EP101AP extension
tube (for the U.S.A.).
• AN-NV6T ceiling-mount bracket, its AN-TK201 and AN-TK202
extension tubes (for countries other than the U.S.A.).
■ Invert the image by setting “Ceiling + Front” in “PRJ Mode”. See
page 
84  for use of this function.
Translucent screen
Audience
Set to “Front”
Audience Tr
anslucent screen Mirror
Set to “Rear”
Audience
Mirror 
						

							-24
INPUT/OUTPUT Terminals and Connectable Main Equipment
AUDIO input (2, 3) terminalConnecting an audio cable. (Shared 
audio input terminal for INPUT 2 
and 3.) (See pages 28 and  29.) 
AUDIO input (1) terminalConnecting an audio cable. 
(Audio input terminal 
dedicated to INPUT 1.) (See 
page  27.)
AUDIO input (4, 5) terminalsConnecting an audio cable. 
(Shared audio input terminals for 
INPUT 4 and 5.) (See page  34.)
WIRED REMOTE terminalFor connecting the remote control when 
the signals from the remote control cannot 
reach the remote control sensor. (See 
page  18.) 
AUDIO OUTPUT terminalConnecting an audio cable. 
(Shared audio output terminal for 
INPUT 1 – 5.) (See page  36.)
LAN terminal(10 BASE-T/100 BASE-TX) Connecting the computer or the 
hub using a LAN cable. (See page 
35.)
INPUT 5 terminalConnecting video equipment with S-video 
output terminal (VCR, DVD player, etc.).
(See page  34.)
RS-232C terminalConnecting the computer to 
control the projector. 
(See page  35.)
INPUT 4 terminalConnecting video equipment without 
S-video output terminal. (See page  34.)
OUTPUT (FOR INPUT 1, 2) 
terminal
Connecting the monitor when you 
want to simultaneously watch the 
projection image on the monitor. 
(See page  36.)INPUT 1, 2 terminalConnecting the computer. (See 
pages  27 and  28 .)
Connecting video equipment with 
component output terminal (DVD 
player, DTV decoder, DVD recorder 
with hard disc, etc.). (See page  33.)
INPUT 3 terminalConnecting the computer. (See 
page  29.)
Connecting video equipment with 
HDMI or DVI output terminal (DVD 
player, DTV decoder, DVD recorder 
with hard disc, etc.). (See pages  30 
and  31 .)
Connections 
						

							Connections
-25
Terminal on the
projector
INPUT 1
INPUT 2
INPUT 3
AUDIO  (for INPUT 1)
AUDIO  (for INPUT 2, 3)
INPUT 3
INPUT 2
INPUT 1
INPUT 2
Equipment
Computer
Audio-visual
equipment
T
erminal on
connected equipment
RGB
output
terminal
DVI digital video
output
terminal
Audio
output
terminal
HDMI
output
terminal
DVI digital video
output
terminal
RGB
output
terminal
Component video
output
terminal Cable
RGB cable (supplied)
5 BNC to 15-pin D-sub cable (commercially available)
DVI Digital cable (commercially available)
ø3.5 mm stereo or mono audio cable (commercially
av
ailable  or available as Sharp service part
QCNWGA038WJPZ)
DVI to HDMI cable (commercially available)
DVI Digital cable (commercially available)
5 RCA RGB cable  (commercially available)
BNC to RCA adaptors (commercially available)
3 RCA to 15-pin D-sub cable (optional: AN-C3CP2)
BNC to RCA adaptors (commercially available)
Component video cable (commercially available)
Samples of Cables for Connection
•F or more details of connection and cables, refer to the operation manual of the connecting equipment.
•Y ou may need other cables or connectors not listed below. 
						

							-26
Terminal on the
projector
INPUT 4
INPUT 5
AUDIO  (for INPUT 1)
AUDIO  (for INPUT 2, 3)
AUDIO  (for INPUT 4, 5)
OUTPUT
AUDIO OUTPUT
Equipment
A
udio-visual
equipment
Monitor
Amplifier
T erminal on
connected equipment
Video
output
terminal
S-video
output
terminal
A udio
output
terminal
RGB
input
terminal
Audio
input
terminal
Cable
Video cable (commercially available)
S-video cable (commercially available)
ø3.5 mm stereo minijack to RCA audio cable
(commercially available)
RCA audio cable (commercially available)
RGB cable (supplied or commercially available)
ø3.5 mm stereo minijack to RCA audio cable
(commercially available)
Samples of Cables for Connection