Sharp Xg P560w Projector User Manual

							Basic Operation
-29
Image Projection
Shifting the Lens
In addition to the zoom function and adjustment of projection angle using the adjust-
ment feet, you can adjust the position of the projection using the lens shift function.
This is a useful function in cases such as when the screen cannot be moved.
Adjustable range
•
• •
•
• The adjustable range is shown below.
Horizontal range: 
±35%
Ve rtical range: 
±66%
The adjustable range has limitations even within the range shown above.
Select the correct type of lens that match with the installed lens (see page  62).
•
• •
•
• The image can be adjusted as shown on the diagram.
•
• •
•
• Allow a margin of error in the value.
Adjustable
range
When moving upward or downward  When moving in the left and right direction
Adjustable rangeAdjustable range
H: Height of the imageW: Width of the imageH: Height of the imageW: Width of the image
AN-P15EZ, AN-P18EZ, AN-P23EZ, AN-P30EZ, AN-P45EZ
AN-P8EX, AN-P12EX
W X 20%
W X 35% W X 35% W X 20%
W H X 37%
H X 37%
H X 66%
H
H X 66%
W X 11%
W X 11% W
H X 22%
H
H X 22%
P osition of the image when the image is centered, both 
ve rtically and horizontally, in lens shift P
osition of the image when the image is centered, both 
ve rtically and horizontally, in lens shift 
						

							-30
Using the Adjustment Feet
•When the position of the projected image cannot be adjusted
with the lens shift function, use the adjustment feet to adjust
the projected angle.
•The height of the projector can be adjusted using the
adjustment feet when the screen is located higher than the
projector, the screen is inclined or when the installation site
is slightly inclined.
•Install the projector so that it is as perpendicular to the
screen as possible.
1Rotate the adjustment feet to
adjust the projected angle.
•The projector is adjustable up to approxi-
mately 5 degrees.
Warning!
•Do not hold the lens and lens cover when
projector angle is adjusted.
•Use caution not to pinch your finger in the
space between the adjustment foot and the
projector when the projector angle is lowered.
1Press H&V LENS SHIFT on the
projector or on the remote control.
•Pressing ENTER on the projector or on
the remote control displays the test pat-
tern. Checking the test pattern is useful
for more accurate adjustment.
2Press ', ", \ or | on the pro-
jector or the remote control to
adjust the image position.
▼On-screen display
Mouse/adjustment 
button 
('/"/\/|) 
ENTER button  H&V LENS SHIFT 
button
UNDO button
ENTER button Adjustment buttons 
('/"/\/|)  H&V LENS SHIFT 
button
UNDO button
Adjustment feet 
Up
Up Down
Down
Note
•When UNDO is pressed, the lens shift reset
screen is displayed. Lens shift can be reset
to factory default with this screen.
Image Projection 
						

							Basic Operation
-31
Note
•After you have pressed FOCUS or ZOOM
on the remote control or the projector, you
can display the test pattern by pressing
ENTER. The test pattern is useful for mak-
ing more accurate adjustments.
•For fine adjustments, when H&V LENS
SHIFT, FOCUS or ZOOM is pressed, the
projected image moves a small amount in
the desired direction for approximately one
second. Hold down the buttons to move the
projected image quickly.
Adjusting the Focus
Press FOCUS +/– on the projector
or on the remote control to adjust the
focus.
Info
•It is recommended that the focus be adjusted
after the projector has warmed up for at least 30
minutes.
Adjusting the Projected Image Size
Press ZOOM +/– on the projector or
on the remote control to adjust the
projected image size.
▼On-screen display
▼On-screen display
ZOOM buttons
FOCUS buttons
ZOOM 
buttonsFOCUS buttons 
						

							-32
For correcting an image desig-
nating the corner of the pro-
jected image
For correcting an image desig-
nating the horizontal or vertical
axes
For correcting the image dis-
tortion which cannot be cor-
rected with “H&V KEY-
STONE”.
*Only when “H&V KEY-
STONE” is set to the values
other than “0”, “IMAGE
RESIZING” can be adjusted.
(This function cannot be used
when correcting with “GEO-
METRIC ADJUSTMENT”.)
GEOMETRIC
ADJUSTMENT
H&V KEYSTONE
IMAGE RESIZING
↑
↑
Selecting the Type of the
Correction
Select the type of the keystone correction.
Press KEYSTONE on the projector or on
the remote control.
•“GEOMETRIC ADJUSTMENT” will be dis-
played.
•Each time 
KEYSTONE is pressed, the display
toggles as follows:
GEOMETRIC→H&V KEYSTONE
ADJUSTMENT
The display←IMAGE RESIZING *
disappears.
Correcting Trapezoidal Distortion
When the image is projected either from the top or from the bottom towards the screen at an angle,
the image becomes distorted trapezoidally.
The function for correcting trapezoidal distortion is called Keystone Correction.
There are the two types of the Keystone Correction.
1) “GEOMETRIC ADJUSTMENT” for correcting an image designating the corner of the projected im-
age
2) “H&V KEYSTONE” for designating the correction of the horizontal and vertical axes
Mouse/adjustment 
button ('/"/\/|)
ENTER button
UNDO button KEYSTONE
button
ENTER button KEYSTONE 
button
UNDO button Adjustment
button ('/"/\/|) 
Image Projection 
						

							Basic Operation
-33
Geometric Adjustment
Upper Left Upper Right Lower Right
Lower Left
GEOMETRIC ADJUSTMENT
1Press KEYSTONE on the pro-
jector or on the remote control
repeatedly until “GEOMETRIC
ADJUSTMENT” is displayed.
2Press the buttons below to ad-
just the position, size or focus
of the projected image.
•Match screen’s four sides to green
test pattern.
•Pressing 
' '' '
', 
" "" "
", 
\ \\ \
\ or 
| || |
| on the projector
or H&V LENS SHIFT on the remote
control allows you to shift the lens.
•Pressing ZOOM +/– on the projector or
on the remote control allows you to ad-
just the projected image size.
•Pressing FOCUS +/– on the projector
or on the remote control allows you to
adjust the focus.
3Press ENTER on the projector
or on the remote control.
4Press ', ", \ or | to move the
position for the upper left of the
image.
•Move the upper left of the yellow frame
onto the upper left of the screen.
5Press ENTER to set the posi-
tion.
6Repeat the same procedure with the
positions for the upper right, lower
right and lower left of the image.
•At this time, pressing UNDO on the pro-
jector or on the remote control returns
to the previous screen.
•Before correcting the upper left of the
image, pressing UNDO returns to the re-
set confirmation screen.
•When the position of the lower left is
set, the correction is made and the
display disappears.
•If the message “Can not correct.” is dis-
played, step 2 may have been performed
incorrectly. In this case, go back to step
2 and try the procedure again.
▼On-screen display 
						

							-34
Vertical Keystone Correction
(Adjustment with 
' / ")
Horizontal Keystone Correction 
(Adjustment with 
\ / |)
▼On-screen display
H&V KEYSTONE
1Press KEYSTONE on the pro-
jector or on the remote control
repeatedly until “H&V KEY-
STONE” is displayed.
•When the correction has already been
made with “GEOMETRIC ADJUST-
MENT”, the confirmation message for
resetting the correction before “H&V
KEYSTONE” is displayed, and then re-
set.
2Press ' or " to parallelize the
left and right sides of the pro-
jected image.
3Press \ or |
      
 to parallelize the
upper and lower sides of the
projected image.
4Press KEYSTONE to display
“IMAGE RESIZING”.
•Only when “H&V KEYSTONE” is set
to the values other than “0”, “IMAGE
RESIZING” works.
▼On-screen display
Image Projection 
						

							Basic Operation
-35
IMAGE RESIZING
(Adjustment with 
' / " / \ / |)5Press ', ", \ or | to correct
the image distortion.
6Press KEYSTONE to set the
position. 
						

							-36
Switching the Input
Mode
Select the appropriate input mode for the con-
nected equipment.
Press COMPUTER1/2, DVI, HDMI,
VIDEO or S-VIDEO on the remote
control to select the input mode.
■When you select the input mode with
INPUT 
P PP P
P/
R RR R
R on the projector or 
P PP P
P/
R RR R
R on
the remote control:
•When 
P PP P
P/
R RR R
R is pressed, the Input list ap-
pears. While the Input list is displayed,
follow the procedure below to switch the
input mode.
–Press 
P PP P
P/
R RR R
R to select the desired input
mode and then press ENTER.
•When “AUTO SEARCH” is selected,
input signal is automatically detected.
•If ENTER is not pressed, the projector
switches to the selected input mode in
a few seconds.
Note
•When no signal is received, “NO SIGNAL”
will be displayed. When non-supported sig-
nal is received, “NOT REG.” is displayed.
•The input mode is not displayed when “OSD
Display” of the “Options1” menu is set to
“Level A” or “Level B”. (See page 57.)
Adjusting the Volume
Press VOL +/–  on the projector or on
the remote control to adjust the volume.
Note
•Pressing VOL– will lower the volume.
Pressing VOL+ will raise the volume.
•When “Pict in Pict” (see page 56) is set to
“On”, audio volume cannot be adjusted on
the projector. The audio volume buttons will
instead function as location shift button for
the smaller screen.
COMPUTER1/2, 
DVI, HDMI, VIDEO 
and S-VIDEO buttons
'/" buttons
"On-screen display
Volume 
buttons
Image Projection
Input mode menu 
						

							Basic Operation
-37
×1×4×9×16×36×64×2×3
"On-screen display
Mouse/adjustment 
button ('/"/\/|) MAGNIFY
(enlarge/reduce)
buttons
UNDO button
RESIZE button
MUTE button
Turning Off the Sound
Temporarily
Press MUTE on the remote control
to temporarily turn off the sound.
Note
•Pressing MUTE again will turn the sound back on.
Displaying an Enlarged
Portion of an Image
Graphs, tables and other portions of projected
images can be enlarged. This is helpful when
providing more detailed explanations.
1Press MAGNIFY  on the re-
mote control.
•Enlarges the image.
•Pressing 
 or  enlarges or re-
duces the projected image.
Note
•You can change the location of the en-
larged image using ', ", \ and |.
2Press UNDO on the remote con-
trol to cancel the operation.
•The magnification then returns to ×1.
Note
In the following cases, the image will
return to the normal size (×1).
-When switching the input mode.
-When UNDO has been pressed.
-When the input signal is changed.
-
When the input signal resolution and
refresh rate (vertical frequency) change.
-When RESIZE has been pressed. 
						

							-38
Freezing a Moving
Image
1Press FREEZE on the remote
control.
•The projected image is frozen.
2Press FREEZE again to return
to the moving image from the
currently connected equipment.
Selecting the Picture
Mode
You can select the suitable picture mode for the
projected image, such as movie or video game.
Press PICTURE MODE on the re-
mote control.
•When pressing PICTURE MODE, the picture
mode changes in order of
Note
•Press UNDO to return to the “STANDARD”
mode while the selected picture mode is dis-
played.
•This function can also be accessed from the
OSD menu (see page 49).
STANDARD PRESENTATION MOVIE CUSTOM
FREEZE button
PICTURE MODE
button UNDO button
Image Projection