Sharp Xg P560w Projector User Manual

Quick Start
-19
Quick Start
Page 21
1.Place the projector facing a screen
Pages 24, 28
Page 28
Press ON on the projector or on the remote control. This section shows the basic operation (projector connecting with the computer). For details, see the page
described below for each step.
Setup and Projection
In this section, connection of the projector and the computer is explained using one example.
2.Connect the projector to the computer and plug the power
cord into the AC socket of the projector
3.Remove...

-20
Pages 29, 30
4.Adjust the angle
5.Adjust the focus and the zoom
Page 31
8.Turn the power off
Page 28
7.Select the input mode
Page 36
1 11 1
1Press FOCUS +/– on the projector or on the remote control to adjust the focus.
2 22 2
2Press ZOOM +/– on the projector or on the remote control to adjust the zoom.
Press INPUT on the projector or COMPUTER1 on the remote control to select the “COMPUTER1” mode.
• •• •
•When you press INPUT on the projector, the INPUT list appears.
Press '/" to switch the...

Setup
-21
Setting Up the Projector
For optimal image quality, position the projector perpendicular to the screen with the projector’s feet flat
and level. Doing so will eliminate the need for Keystone correction and provide the best image quality.
Note
•The projector lens should be centered in the middle of the screen. If the horizontal line passing through
the lens center is not perpendicular to the screen, the image will be distorted, making viewing difficult.
• For an optimal image, position the...

-22
Standard Zoom Lens (AN-P18EZ : Standard Equipment with XG-P560W)
F2.5, f=25.5-32 mm
16:10 Signal Input (Normal Mode)
The formula for picture size and projection distance
[m/cm]
L1 (m) = 0.0392χ
L2 (m) = 0.0491 χ
H1 (cm) = –1.56815 χ
H2 (cm) = 0.2221 χ
W (cm) =  ±0.75379 χ
[Feet/inches]
L1 (ft) = 0.0392 χ
 / 0.3048
L2 (ft) = 0.0491 χ
 / 0.3048
H1 (in) = –1.56815 χ
 / 2.54
H2 (in) = 0.2221 χ
 / 2.54
W (in) =  ±0.75379 χ
 / 2.54
χ
: Picture size (diag.) (in/cm)
L1: Minimum projection distance (m/ft)
L2:...

Setup
-23
Projecting a Reversed Image
Projection from behind the Screen
■Place a translucent screen between the projector and the audience.
■Reverse the image by selecting “Rear” in the “PRJ Mode” menu. (See page 62.)
Projection Using a Mirror
■Place a mirror (normal flat type) in front of the lens.
■When the translucent screen is placed between the mirror and audience, select “Front” in the “PRJ Mode”
menu. (See page 62.)
■When the mirror is placed on the audience side, select “Rear” in the “PRJ Mode”...

-24
Connecting the Projector to Other Equipment
Before connecting, ensure that the power cord of the projector is unplugged from the AC outlet and turn off
the equipment to be connected. After making all connections, turn on the projector and then the other
pieces of equipment. When connecting a computer, ensure that it is the last equipment to be turned on after
all the connections are made.
IMPORTANT: Ensure that the appropriate input mode has been selected on the projector before you
turn on the...

Connections
-25
Note
•Select the input signal type of the video equipment when connecting to the COMPUTER1/2, DVI-D or
HDMI terminal. See page 51.
•The HD/C sync and VD terminals may be used depending on the specifications of the DTV decoder
connected to this projector. Please refer to the operation manual of the DTV decoder for details.
•The HD/C sync terminal of the 5 BNC terminal is only for TTL signal.
•Select “480P” or “576P” for “Resolution” on the “Fine Sync” menu, if necessary. (See page 53.)...

-26
Video equipment, 
Camera, Video gameS-video cable (commercially available)S-video output terminal
Video output terminalS-VIDEO
VIDEO
RCA audio cable (commercially available) A
udio output terminal
RCA audio cable (commercially available)
A udio output terminal Video cable (commercially available)
MonitorMONITOR OUTRGB input terminalRGB cable (supplied or commercially available)
Amplifier
MONITOR OUTA udio  input  terminal
Equipment CableTerminal on connected equipmentTerminal on the projector
ø3.5 mm...

Connections
-27
Controlling the Projector by a Computer
When the RS-232C terminal on the projector is connected to the RS-232C serial terminal on
the computer, or when the LAN terminal on the projector is connected to the LAN terminal on
the computer, the computer can be used to control the projector. Refer to the “SETUP MANUAL”
contained on the supplied CD-ROM for details.
When connecting to a computer using an RS-232C serial control cable
Note
•The RS-232C function may not operate if your computer...

-28
Turning the Projector On/Off
Info
•When “Auto Restart” is set to “On”:
If the power cord is unplugged from the AC outlet or the
breaker switch is turned off when the projector is on,
then the projector automatically turns on when the power
cord is plugged into the AC outlet or the breaker switch
is turned on. (See page 63.)
•English is the factory preset language. If you want to change
the on-screen display to another language, change the lan-
guage according to the procedure on page 65.
▼On-screen...