Sharp Xg Nv6xu Projector Quickstart Guide

							Quick Reference for XG-
NV6X
A. Connecting the Power Cord
Plug the supplied power cord into the AC socket on the back of the
projector.
B. Connecting a Computer
1Slide the 15 pin/BNC switch on the rear terminals to the 15 pin
position.
2Plug one end of the supplied computer cable into the INPUT 1
or 2 port on the projector and the other end into the monitor
output port on the computer, and secure the plugs by tightening
the thumb screws.
3Plug one end of the supplied computer audio cable into AUDIO
INPUT 1 or 2 terminal on the projector and the other end into
the audio output port on the computer.
4Press POWER ON.
5Turn on the computer.
6Press AUTO SYNC to adjust the image.
C. Connecting the Remote Mouse Receiver
IBM or IBM compatible PC
1Connect one end of the supplied mouse control cable to the
corresponding terminal on the PC.
2Connect the other end to the remote mouse receiver.
Macintosh
1Connect the mouse control serial cable to the remote mouse
receiver.
2Connect the mouse control cable for Mac to the Mac ADB
port on the Mac.
3Connect the other end of the mouse control cable for Mac to
the mouse control serial cable.
¥ Make sure that your computer is turned off while making any mouse control cable
connections.
¥ When using the wireless mouse with an IBM or IBM compatible PC, you can use
either a PS/2 or serial cable connection. (See diagram below.)
¥ Use the supplied mouse control cable for Mac when using the remote mouse receiver
with a Macintosh computer.
Mouse control
serial cable Mouse control cable for IBM PS/2Use this terminal to connect the
supplied mouse control cable
to the remote mouse receiver.
Remote mouse receiver
D. Connecting a DVD Player, DTV Decoder
and Other Component Video Equipment
1Slide the 15 pin/BNC switch on the rear terminals to the BNC
position.
2Plug the supplied BNC-RCA adaptors to INPUT 1 terminals
(R(P
R), G/G sync(Y), B(PB)).
3Connect a component cable and an audio cable to the
corresponding terminals on the projector and video source.
Audio cable
(sold separately)To audio output terminal
To analog component
output terminals
Component cable
(sold separately)
Three BNC-RCA adaptorsDTV decoder
or
DVD player POWER ON
button
AUTO SYNC
button
LCD Projector
Mouse control
cable for Mac
While this projector can input COMPUTER/RGB and
COMPONENT signals through the 15-pin D-sub terminals (INPUT
1 and 2 ports) and BNC terminals (INPUT 1 terminals), the
projector cannot distinguish between the two types of signals.
When inputting these signals through the aforementioned
terminals, you must indicate the input signal type. (See ÒSelecting
the Signal TypeÓ in the operation manual.)
XG-NV6XU/QR (E)99.11.8, 2:05 PM 1 
						

							INPUT 2 Mode
E. Connecting a VCR, Laser Disc Player and
Other Audiovisual Equipment
1Connect the yellow (Video) RCA connector to the corresponding
yellow terminals on the projector and video source.
2Connect the red and white (Audio) RCA connectors to the
corresponding red and white terminals on the projector and
video source.g
gg
g
2Press ENTER to display test pattern.
3Press ¶/Ä/§/© to make adjustments.
4a. Press LENS until normal screen appears.
4b.To reset the KEYSTONE setting, press UNDO.
¥ Straight lines and the edges of the displayed image may appear jagged, when
adjusting the KEYSTONE setting.
¥ Do not touch the lens when adjusting the focus or zoom.
H. Turning the Projector Power off
1Press POWER OFF.
Power OFF
button
2Press POWER OFF again while the message is displayed.
Printed in Japan
TINS-6738CEZZ
9P06-JWG
To video output terminal
To S-video output terminalVCR
or
Laser disc player Audio cable
(sold separately)
S-video cable (sold separately)Video cable (sold separately)To audio output terminals
VIDEO Mode
F. Selecting and Checking the Input Mode
1Press INPUT to select the desired input mode.
2Press INPUT again to change the mode.
EXAMPLE
INPUT 1 Mode
INPUT button
G. Adjusting the Lens
2 3 1, 4a
4b
1Press LENS to select mode. Each time LENS is pressed, the
screen changes in the following order.
Use this terminal when the
audio-visual equipment to be
connected has an S-VIDEO
output terminal.
PDF operation manuals in several languages are included in the CD-ROM. See ÒHow to Access the
PDF Operation ManualsÓ in the operation manual of the projector for more details.
XG-NV6XU/QR (E)99.11.8, 2:05 PM 2