Sharp Xg Nv4su Projector User Manual

							Operation
E-10
Setting Up the Projector (Standard Setup)
Optimal image quality can be achieved when the projector is positioned perpendicular to the screen with all
feet flat and level.
¥ Position the screen so that it is not in direct sunlight or room light. Light falling directly onto the screen washes out colors,
making viewing difficult. Close the curtains and dim the lights when setting the screen in a sunny or bright room.
Example of a standard setup
Top ViewSide View
90˚
Lens center Lens center
The projector lens should be centered in the middle of
the screen.If the lens center is not perpendicular to the screen, the
image will be distorted, making viewing difficult.
¥ For information on projector distance and picture size, see page 23.
¥ For reversed image and ceiling-mount setups, see page 24.
¥ A polarizing screen cannot be used with this projector.
90˚
Adjusting the Height of the Picture
You can adjust the height of the picture by raising the projector with the adjuster release.
a. Extending the adjuster leg
Press the adjuster release and lift the projector
to the desired angle.
b. Locking the adjuster leg in position
Remove your hand from the adjuster release,
and then release the projector once you are
sure the adjuster leg has locked in position.
Returning the projector to its original position
While holding the projector, press the adjuster release
and slowly lower the projector to its original position.
¥ The projector is adjustable up to approximately 5¡ from
the horizontal.
¥ When an adjustment is made, the image may become
distorted, depending on the relative positions of the pro-
jector and the screen.
CAUTION
¥ Do not press the adjuster release when the adjuster leg is
extended without firmly holding the projector.
¥ Do not hold the lens when lifting or lowering the projector.
¥ When lowering the projector, be careful not to get your
fingers caught in the area between the adjuster leg and
the projector.
a
Adjuster release
b
Adjuster release
XG-NV4SU (E)-b98.10.19, 5:34 PM 10 
						

							Operation
E-11
Basic Operations
a
b
c
d
When the main power is
on, the POWER indicator
lights up red.
When the power is on,
the LAMP REPLACE-
MENT indicator flashes
to show the operating
condition of the lamp.
Green: Lamp is ready.
Flashing green: Warming
up.
Red: Change the lamp.
Focus knob
e
Zoom knob
or
ON
a. Connecting the Power Cord
Plug the supplied power cord into the AC
socket on the back of the projector.
b. Turning on the Main Power
Press the MAIN POWER switch on the back of
the projector. The POWER indicator lights up
red and the projector enters standby mode.
¥ When the main power is not on, the remote control cannot
be used to operate the projector.
c. Turning on the Power
Press POWER ON on the projector or the
remote control.
¥ The flashing green LAMP REPLACEMENT indicator
shows that the lamp is warming up. Wait until the indica-
tor stops flashing before operating the projector.
¥ If the power is turned off and then immediately turned on
again, it may take a short while before the lamp turns on.
(During this period, the LAMP REPLACEMENT indicator
flashes.)
¥ After the projector is unpacked and turned on for the first
time, a slight odor may be emitted from the exhaust vent.
This odor will soon disappear with use.
d. Adjusting the Focus
Slide the focus knob until the image on the
screen becomes clear.
e. Adjusting the Zoom
Slide the zoom knob. The image can be ad-
justed to the desired size within the zoom
range.
f. Selecting the On-screen Display
Language
(See page 14 for details on using the
menu screens.)
The On-screen Display is set to ÒENGLISHÓ at
the factory. The language for the On-screen
Display can be set to English, German,
Spanish, Dutch, French, Italian, Swedish or
Japanese.
1. Press MENU to display the menu screen. Press
ADJUSTMENT ¶/Ä to select ÒLANGUAGEÓ.
Then press ENTER to display the ÒLANGUAGEÓ
screen.
2. Press ADJUSTMENT ¶/Ä to select the lan-
guage you want to display on the screen. Then
press ENTER. The On-screen Display is now
programed to display in the language selected.
On-screen Display
RGB1  ADJ.
RGB1  INPUT  ADJ.
IMAGE  ADJ.
AUDIO
SYSTEM  SETUP
LANGUAGE
:SEL.:NEXTENTER:ENDMENU
LANGUAGE
:SEL.:ENTERENTER:ENDMENU
NEDERLANDS ESPAÑOL
DEUTSCH
ENGLISH
SVENSKA ITALIANO FRANÇAIS
f.1 f.2
g
XG-NV4SU (E)-b98.10.19, 5:35 PM 11 
						

							Operation
E-12
Basic Operations
g. Selecting the Video Input System
Mode
The video input system mode is set to ÒAUTOÓ
at the factory; however, it can be changed to a
different system mode, if the selected system
mode is not compatible with the connected
audiovisual equipment (such as when a color
image appears in black and white, etc.).
1. Press MENU to display the menu screen. Press
ADJUSTMENT ¶/Ä to select ÒIMAGE ADJ.Ó
Then press ENTER to display the ÒIMAGE ADJ.Ó
screen.
2. Press ADJUSTMENT ¶/Ä to select ÒSYSTEMÓ.
Then press ENTER to display the ÒSYSTEMÓ
screen.
3. Press ADJUSTMENT ¶/Ä to select the desired
video system mode. Then press ENTER.
¥ In AUTO mode, ÒPALÓ, ÓSECAMÓ, ÒNTSC 4.43Ó or ÒNTSC
3.58Ó is displayed on the screen for a few seconds when
the system mode is changed using INPUT SELECT on
the projector.
¥ When the system mode is set to ÒAUTOÓ, you may not
receive a clear picture due to signal differences. Should
this occur, switch to the color system you are viewing.
h. Selecting the Input Mode
1. Press INPUT SELECT on the projector to select
the input mode. When you press the button, the
current input mode will be displayed on the
screen for 4 seconds. If you press it again while
the input mode is displayed, the mode changes
as shown on the left.
¥ The input mode can be selected by directly pressing
COMPUTER or VIDEO on the remote control. (When
COMPUTER is pressed, ÒRGB1Ó and ÒRGB2Ó will appear
accordingly.)
2. Press INPUT SELECT on the projector to con-
firm the selected input mode.
¥ In VIDEO mode, the video system being received will be
indicated below the ÒVIDEOÓ display.
¥ In RGB mode, the resolution being displayed will be indi-
cated below the ÒRGB1Ó or ÒRGB2Ó display.
¥ When no signals are being received, ÒNO SIGNALÓ will
be displayed. When a signal that the projector is not pre-
set to receive is being received, ÒNOT REG.Ó will be dis-
played.
¥ The picture size differs in ÒRGBÓ, ÒPALÓ, ÒSECAMÓ and
ÒNTSCÓ modes.
VIDEO  ADJ.
BACKGRND LVL
IMAGE  ADJ.
AUDIO
SYSTEM  SETUP
LANGUAGE
:SEL.:NEXTENTER:ENDMENU:SEL.:NEXTENTER:ENDMENU
BLUE  SCREEN
BLK SCRN DISP IMAGE  ADJ.
REVERSE
INVERT INPUT  DISPLAY[OFF]
[OFF]
[
OFF]SYSTEM[OFF] [
ON]
g.1 g.2
g
AUTO
SYSTEM
PAL
SECAM
NTSC 4.43
NTSC 3.58
:SEL.:ENTERENTER:ENDMENU
g.3
On-screen Display
h
Mac
To view the image
from a source
connected to:
VIDEO INPUT
COMPUTER INPUT 1
COMPUTER INPUT 2
XG-NV4SU (E)-b98.10.19, 5:35 PM 12 
						

							Operation
E-13
i
Basic Operations
i. Checking the Input Mode
Press INPUT SELECT on the projector or IN-
PUT CHECK on the remote control. The current
input mode will be displayed on the screen for 4
seconds.
j. Adjusting the Volume
Press VOLUME (VOL) `/1 on the projector or
the remote control. The number of displayed
segments (0Ð60) increases or decreases as the
volume is raised or lowered.
To temporarily turn off the sound
Press MUTE on the projector or the remote control.
To turn the sound back on
Press MUTE once again.
k. Turning off the Power
1. Press POWER OFF on the projector or the
remote control. The screen on the left will
appear.
2. To turn off the power, press POWER OFF
again while the screen is displayed. The
power is now temporarily turned off.
¥ If you accidentally pressed POWER OFF and do not
want to turn off the power, wait until the screen disap-
pears.
When POWER OFF is pressed twice, the POWER
indicator will light up red and the cooling fan will
run for about 90 seconds. The projector will then
enter standby mode.
The power can be turned on again by pressing
POWER ON on the projector or the remote control.
When the power is turned on, the POWER indicator
and the LAMP REPLACEMENT indicator light
green.
¥ When the main power is off on the projector, the power
cannot be turned on from the remote control.
On-screen
Display
Mac
k
TURNPOWEROFF?
YES: PRESS
NO : PLEASE WA I TAGAIN
j
VOLUME
38
orOFF
XG-NV4SU (E)-b98.10.19, 5:36 PM 13 
						

							Operation
E-14
(When using the remote control to operate the menu screens, slide the MOUSE/ADJUSTMENT
switch to the ADJ. position.)
1. Press MENU on the projector or the remote control to display the RGB1, RGB2 or
VIDEO mode menu screen.
2. Press ADJUSTMENT 
¶ ¶¶ ¶
¶/
Ä ÄÄ Ä
Ä on the projector or the remote control to select the item
you want to adjust, then press ENTER to display the sub menu screen.
¥ For details on items on the sub menu screen and their settings, see pages indicated in the tables above.
Using the Menu Screens
This projector has two sets of menu screens that allow you to adjust the picture and various projector settings.
These menu screens can be operated from the projector or the remote control with the following buttons.
Remote control
ONMUTE
BLACK
SCREEN
R-CLICK ENTERCOMPUTER
MOUSE
LIGHT
LCD PROJECTORADJ. VIDEO
CHECKAUTO SYNC
MENU LASER
VOLOFF
Projector
PICTURE, BRIGHT, RED, BLUE (p. 15)
AUTO SYNC, CLOCK, PHASE, HORIZONTAL POSITION, VERTICAL
POSITION, MODE, MEMORY SELECT (pp. 16, 17)
AUTO SYNC DISPLAY, BLACK SCREEN DISPLAY, INPUT DISPLAY,
REVERSE, INVERT (pp. 20Ð22)
TREBLE, BASS (p. 18)
RESOLUTION, HORIZONTAL FREQUENCY, VERTICAL FREQUENCY,
LAMP USAGE TIME (p. 19)
ENGLISH, DEUTSCH, ESPA„OL, NEDERLANDS, FRAN‚AIS, ITALIANO,
SVENSKA, JAPANESE (p. 11)RGB ADJUSTMENT
RGB INPUT
ADJUSTMENT
IMAGE
ADJUSTMENT
AUDIO
SYSTEM SETUP
LANGUAGE
Items on the RGB1 or RGB2 Menu ScreenMenu Screen in RGB1 Mode
RGB1  ADJ.
RGB1  INPUT  ADJ.
IMAGE  ADJ.
AUDIO
SYSTEM  SETUP
LANGUAGE
:SEL.:NEXTENTER:ENDMENU
PICTURE, BRIGHT, COLOR, TINT, SHARPNESS (p. 15)
RED, BLUE (p. 19)
BLUE SCREEN, BLACK SCREEN DISPLAY, INPUT DISPLAY, SYSTEM,
REVERSE, INVERT (pp. 12, 20Ð22)
TREBLE, BASS (p. 18)
LAMP USAGE TIME (p. 19)
ENGLISH, DEUTSCH, ESPA„OL, NEDERLANDS, FRAN‚AIS, ITALIANO,
SVENSKA, JAPANESE (p. 11)VIDEO ADJUSTMENT
BACKGROUND LEVEL
IMAGE
ADJUSTMENT
AUDIO
SYSTEM SETUP
LANGUAGE
Items on the VIDEO Menu ScreenMenu Screen in VIDEO Mode
VIDEO  ADJ.
BACKGRND LVL
IMAGE  ADJ.
AUDIO
SYSTEM  SETUP
LANGUAGE
:SEL.:NEXTENTER:ENDMENU
MENU button
ADJUSTMENT ¶/Ä buttons
ENTER button
MOUSE/ADJUSTMENT
switchMENU button
ADJUSTMENT
¶/Ä buttons
ENTER button
XG-NV4SU (E)-b98.10.19, 5:36 PM 14 
						

							Operation
E-15
Picture Adjustments
This projectorÕs picture is factory preset to standard settings. However, you can adjust it to suit your own prefer-
ences by adjusting the four picture modes: ÒPICTUREÓ, ÒBRIGHTÓ, ÒREDÓ and ÒBLUEÓ. The adjustments can be
stored in the ÒRGB1Ó, ÒRGB2Ó and ÒVIDEOÓ modes separately. (The following steps are used as an example in
adjusting the picture in ÒRGB1 ADJ.Ó mode.)
a. Displaying the ÒRGB1 ADJ.Ó screen
Press MENU to display the menu screen. Press
ADJUSTMENT ¶/Ä to select ÒRGB1 ADJ.Ó
Then press ENTER to display the ÒRGB1 ADJ.Ó
screen.
¥ The menu screen is displayed for about 30 seconds.
b. Adjusting the picture
1. Press ADJUSTMENT ¶/Ä to select the
item you want to adjust.
To display only the adjustment item, press
ENTER after selecting the item. Only the
setting screen for the selected adjustment
item will appear.
2. Press ADJUSTMENT §/© to move the 
mark of the selected adjustment item to the
desired setting.
3. Press ENTER to return to the ÒRGB1 ADJ.Ó
screen.
¥ The ÒRGB1 ADJ.Ó screen is displayed for about 30 sec-
onds.
Description of Adjustment Items
¥ When a VIDEO input mode is selected, only ÒPICTUREÓ,
ÒBRIGHTÓ, ÒCOLORÓ, ÒTINTÓ and ÒSHARPNESSÓ can be
adjusted.
¥ ÒTINTÓ appears only in ÒNTSC 3.58Ó mode.
To return to normal screen, press MENU.
ADJUSTMENT §
For less contrast
For less brightness
For weaker red
For weaker blue
For less color intensity
Skin tones become purplish
For less sharpnessSelected item
PICTURE
BRIGHT
RED
BLUE
COLOR
TINT
SHARPNESS
RESETADJUSTMENT ©
For more contrast
For more brightness
For stronger red
For stronger blue
For more color intensity
Skin tones become greenish
For more sharpness
All RGB video adjustment items are returned to the factory
preset settings.
¥ To reset all adjustment items, select ÒRESETÓ on the ÒRGB 1
ADJ.Ó screen and press ENTER.
On-screen Display
a
RGB1  ADJ.
RGB1  INPUT  ADJ.
IMAGE  ADJ.
AUDIO
SYSTEM  SETUP
LANGUAGE
:SEL.:NEXTENTER:ENDMENU
RGB1  ADJ.
BRIGHT
RED
BLUE
RESET +
0 0
0
0
:SEL.
:ADJ.:NEXTENTER:ENDMENU
- + - + - + -
PICTURE
 +
:SEL.
:ADJ.:ENTERENTER:ENDMENU
-PICTURE 0
b.1
or
XG-NV4SU (E)-b98.10.19, 5:36 PM 15 
						

							Operation
E-16
Computer Adjustments
When displaying computer patterns which repeat every dot (tiling, vertical stripes, etc.), interference may occur
between the LCD pixels, causing flickering, vertical stripes, or contrast irregularities in portions of the screen.
Should this occur, adjust ÒCLOCKÓ, ÒPHASEÓ, ÒH-POSÓ and ÒV-POSÓ for optimum computer image.
a. Displaying the ÒRGB1 INPUT ADJ.Ó screen
Press INPUT SELECT to select the input you want to adjust
(ÒRGB1Ó in this example) and press MENU to display the
menu screen. Press ADJUSTMENT ¶/Ä to select ÒRGB1
INPUT ADJ.Ó Then press ENTER to display the ÒRGB1
INPUT ADJ.Ó screen.
b. Adjusting the computer input item
Press ADJUSTMENT ¶/Ä to select the item you want to
adjust. To display only the item you want to adjust, press
ENTER after selecting the item with ADJUSTMENT ¶/Ä.
Then press ADJUSTMENT §/© to adjust the item.
Description of Adjustment Items
Auto Sync Adjustment
Used to automatically adjust the RGB input signals when
turning on the projector to achieve optimum images.
¥ When ÒAUTO SYNCÓ is set to ÒONÓ, adjustments to the computer set-
tings are automatically made when the projector is turned on or when
the COMPUTER/RGB mode is changed.
¥ When ÒAUTO SYNCÓ is set to ÒOFFÓ, automatic adjustments can be
made by pressing AUTO SYNC on the projector or the remote control.
During Auto Sync Adjustment, the On-screen Display on the left
appears.
¥ Auto Sync Adjustment may take some time to complete depending on
the image of the computer connected to the projector.
¥ To display a blue screen (in place of the Auto Sync Adjustment screen),
see ÒAuto Sync Display Function (RGB mode only)Ó on page 20.
Manual Adjustment
Used when Auto Sync Adjustment is not effective.
CLOCK SPEED ADJUSTMENT (FAST/SLOW): Used to adjust the
input signal horizontal frequency and the dot clock.
PHASE ADJUSTMENT (UP/DOWN): Used to reduce image dis-
tortion or improve contrast.
HORIZONTAL POSITION ADJUSTMENT (LEFT/RIGHT): Used to
center the on-screen image by moving it to the left or right.
VERTICAL POSITION ADJUSTMENT (UP/DOWN): Used to center
the on-screen image by moving it up or down.
Mode Adjustment
CONNECTING TO IBM-PC COMPUTERS
¥ Ordinarily, the type of input signal is detected and the correct
resolution mode (Text or Graphics) is automatically selected.
However, for the following signals, set ÒMODEÓ to ÒONÓ or ÒOFFÓ
to select the projectorÕs resolution mode to match the computer
display mode properly.
720 dots 2 400 lines, 720 dots 2 350 lines (Text Mode)
640 dots 2 400 lines, 640 dots 2 350 lines (Graphic Mode)
¥ For text mode, set ÒMODEÓ to ÒOFFÓ.
¥ For graphic mode, set ÒMODEÓ to ÒONÓ.
CONNECTING TO MACINTOSH SERIES COMPUTERS
¥ When connecting to a Macintosh II with 35 kHz dot frequency,
set ÒMODEÓ to ÒONÓ.
¥ When connecting to a Macintosh LC Series computer with
34.79 kHz dot frequency, set ÒMODEÓ to ÒOFFÓ.
On-screen Display
a
RGB1  ADJ.
RGB1  INPUT  ADJ.
IMAGE  ADJ.
AUDIO
SYSTEM  SETUP
LANGUAGE
:SEL.:NEXTENTER:ENDMENU
RGB1  INPUT ADJ.
 +
:SEL.:NEXTENTER:ENDMENU
[–––]
- + - + - + -PHASEH-POSV-POSMODE
[OFF]AUTO SYNC
RESET
MEMORY SELECT 0 0
0
0
CLOCK
:ADJ.
 +
:SEL.
:ADJ.:ENTERENTER:ENDMENU
-CLOCK0
b
or
ADJUSTING THE IMAGE
XG-NV4SU (E)-b98.10.19, 5:37 PM 16 
						

							Operation
E-17¥ When connecting third party video cards and other
Macintosh computers, set ÒMODEÓ to ÒONÓ or ÒOFFÓ to
select the correct display mode.
¥ When the input signal is automatically detected or when
there is no input signal, ÒMODE(---)Ó appears on the
screen and the display mode cannot be changed.
Initial Reset
To return ÒCLOCKÓ, ÒPHASEÓ, ÒH-POSÓ and ÒV-POSÓ
adjustments to their initial settings, select ÒRESETÓ
and then press ENTER.
Memory Select
Used to store up to seven computer mode
adjustments. (See below.)
¥ Avoid displaying computer patterns which repeat every other
line (horizontal stripes). (Flickering may occur, making the image
hard to see.)
To return to normal screen, press MENU.
Computer Mode Memory Adjustments
This projector allows you to store up to seven RGB
input adjustment settings for use with various
computers. Once these settings are stored, they can
be easily selected each time you connect the
computer to the projector.
a. Customizing the RGB input
adjustment settings
1. Press MENU to display the menu screen. Press
ADJUSTMENT ¶/Ä to select ÒRGB1 INPUT
ADJ.Ó Then press ENTER to display the ÒRGB1
INPUT ADJ.Ó screen.
2. Press ADJUSTMENT ¶/Ä to select ÒMEMORY
SELECTÓ. Then press ENTER to display the
ÒMEMORY SELECTÓ screen.
3. Press ADJUSTMENT Ä once, then press
ADJUSTMENT §/© to select the number of the
memory adjustment mode you want to adjust.
¥ If the memory position has not been set, ÒNONÓ will appear on
the screen.
¥ Memory No. 0 cannot be set. It contains the fixed factory preset
setting.
4. Press ADJUSTMENT ¶/Ä to select ÒSETTINGÓ.
Then press ENTER to return to the ÒRGB1 INPUT
ADJ.Ó screen.
5. Press ADJUSTMENT ¶/Ä to select the item you
want to adjust. Then press ADJUSTMENT §/©
to adjust the setting.
6. Press MENU to store the adjusted RGB input
adjustment setting under the number of the
selected memory adjustment mode.
Computer Adjustments
RGB1  ADJ.
RGB1  INPUT  ADJ.
IMAGE  ADJ.
AUDIO
SYSTEM  SETUP
LANGUAGE
:SEL.:NEXTENTER:ENDMENU
MEMORY  SELECT
SETTING
:SEL.:BACKENTER:ENDMENU
 0 1 2 3 4 5 6 7
MEMORY  SELECT
:SEL.
:ADJ.ENTER:ENDMENU
 0 1 2 3 4 5 6 7
RESOLUTION
HOR  FREQ
VERT  FREQ
SETTING
:ENTER
HzKHz  60.0
 75  1024´768
RGB1  INPUT ADJ.
 +
:SEL.:NEXTENTER:ENDMENU
[–––]
- + - + - + -
PHASEH-POSV-POSMODE
[OFF]AUTO SYNC
RESET
MEMORY SELECT 0 0
0
0
CLOCK
MEMORY  SELECT
NON
SETTING
:SEL.ENTER:ENDMENU
 0 1 2 3 4 5 6 7
:ENTER
On-screen Display
a.1 a.2 (a.5)
a.3
a.4
XG-NV4SU (E)-b98.10.19, 5:37 PM 17 
						

							Operation
E-18
Audio Adjustments
This projectorÕs audio is factory preset to standard settings. However, you can adjust it to suit your own prefer-
ences by adjusting ÒTREBLEÓ and ÒBASSÓ.
On-screen Display
a. Displaying the ÒAUDIOÓ screen
Press MENU to display the menu screen. Press
ADJUSTMENT ¶/Ä to select ÒAUDIOÓ. Then
press ENTER to display the ÒAUDIOÓ screen.
b. Adjusting the audio
1. Press ADJUSTMENT ¶/Ä to select the
audio item you want to adjust.
2. Press ADJUSTMENT §/© to move the
mark of the selected adjustment item to
the desired setting.
Description of Adjustment Items
RGB1  ADJ.
RGB1  INPUT  ADJ.
IMAGE  ADJ.
AUDIO
SYSTEM  SETUP
LANGUAGE
:SEL.:NEXTENTER:ENDMENU
AUDIO
TREBLE
BASSRESET0
0
:SEL.
:ADJ.:ENDMENU
 + - + -
a
b
ADJUSTMENT §
For weaker treble
For weaker bassSelected item
TREBLE
BASS
RESETADJUSTMENT ©
For stronger treble
For stronger bass
All audio adjustment items are returned to the factory preset
setting.
¥To reset all adjustment items, select ÒRESETÓ on the ÒAUDIOÓ
screen and press ENTER.
To return to normal screen, press MENU.
XG-NV4SU (E)-b98.10.19, 5:37 PM 18 
						

							Useful Features
E-19
On-screen Display
RGB1  ADJ.
RGB1  INPUT  ADJ.
IMAGE  ADJ.
AUDIO
SYSTEM  SETUP
LANGUAGE
:SEL.:NEXTENTER:ENDMENU
Checking the System Setup
This function allows you to check the current input signal and lamp usage time.
a. Displaying the ÒSYSTEM SETUPÓ
screen
Press MENU to display the menu screen. Press
ADJUSTMENT ¶/Ä to select ÒSYSTEM SET-
UPÓ. Then press ENTER to display the ÒSYS-
TEM SETUPÓ screen.
b. Checking the system setup
The current system condition, including the
lamp usage time, will be displayed.
¥ In VIDEO mode, the resolution and frequency settings will
not be displayed.
To return to normal screen, press MENU.
Background Level (VIDEO mode only)
This function allows you to adjust the picture white balance (ÒREDÓ and ÒBLUEÓ) for the selected video input to
achieve optimal image quality.
¥ This function cannot be used when RGB mode is selected.
a. Displaying the ÒBACKGRND LVLÓ
screen
Press MENU to display the menu screen. Press
ADJUSTMENT ¶/Ä to select ÒBACKGRND
LVLÓ. Then press ENTER to display the
ÒBACKGRND LVLÓ screen.
b. Adjusting the background level
1. Press ADJUSTMENT ¶/Ä to select the
item you want to adjust. To display only the
adjustment item, press ENTER after
selecting the item. Only the setting screen
for the selected adjustment item will appear.
2. Press ADJUSTMENT §/© to move the
mark of the selected adjustment item to
the desired setting.
To return to normal screen, press MENU.
¥ See the table on page 15 for the description of adjust-
ment items.
VIDEO  ADJ.
BACKGRND LVL
IMAGE  ADJ.
AUDIO
SYSTEM  SETUP
LANGUAGE
:SEL.:NEXTENTER:ENDMENU
a
a
b.1
 +
:SEL.
:ADJ.:ENTERENTER:ENDMENU
-RED0or
BACKGRND LVLRED
BLUE
RESET + 0
0
:SEL.
:ADJ.:NEXTENTER:ENDMENU
- + -
SYSTEM  SETUP
RESOLUTION
HOR  FREQ
VERT  FREQ
:SEL.:ENDMENU
 800@600
 60Hz
LAMP USAGE 1234H 37.9 KHz
:BACKENTER
b
XG-NV4SU (E)-c98.10.19, 5:38 PM 19