Sharp Xg Mb67xl Projector Technical Manual
Have a look at the manual Sharp Xg Mb67xl Projector Technical Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 615 Sharp manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
![Page 22
-22
Save Settings and Quit
([S]Save & Quit)
Save set values and quit menu.1
1 1
1
1 Enter “s” and press the “Enter” key.
2
2 2
2
2 Enter “y” and press the “Enter” key.
▼
SETUP MENU
---------------------------------SETUP MENU-----------------------------\
---
[1]IP Address [2]Subnet Mask [3]Default Gateway
[4]User Name [5]Password
[6]RS-232C Baud Rate [7]Projector Name
[8]DHCP Client[A]Advanced Setup [D]Disconnect All
[V]View All Setting [S]Save & Quit [Q]Quit Unchanged
setup>s
All Connection will be...](http://img.usermanuals.tech/thumb/68/96210/w64_sharp-xg-mb67xl-technical_d-21.png "Page 22
-22
Save Settings and Quit
([S]Save & Quit)
Save set values and quit menu.1
1 1
1
1 Enter “s” and press the “Enter” key.
2
2 2
2
2 Enter “y” and press the “Enter” key.
▼
SETUP MENU
---------------------------------SETUP MENU-----------------------------\
---
[1]IP Address [2]Subnet Mask [3]Default Gateway
[4]User Name [5]Password
[6]RS-232C Baud Rate [7]Projector Name
[8]DHCP Client[A]Advanced Setup [D]Disconnect All
[V]View All Setting [S]Save & Quit [Q]Quit Unchanged
setup>s
All Connection will be...")
![Page 23
-23
IP Address Setting
([1]IP Address)
Setting of IP address.1
1 1
1
1 Enter “1” and press the “Enter” key.
2
2 2
2
2 Enter numerical value to be set and press the
“Enter” key.
Display IP address after change (*).
Subnet Mask Setting
([2]Subnet Mask)
Setting subnet mask.
1
1 1
1
1 Enter “2” and press the “Enter” key.
2
2 2
2
2 Enter numerical value to be set and press the
“Enter” key.
Display subnet mask after change (*).
The setting procedure for each item will be explained. For the basic pro\
cedure,...](http://img.usermanuals.tech/thumb/68/96210/w64_sharp-xg-mb67xl-technical_d-22.png "Page 23
-23
IP Address Setting
([1]IP Address)
Setting of IP address.1
1 1
1
1 Enter “1” and press the “Enter” key.
2
2 2
2
2 Enter numerical value to be set and press the
“Enter” key.
Display IP address after change (*).
Subnet Mask Setting
([2]Subnet Mask)
Setting subnet mask.
1
1 1
1
1 Enter “2” and press the “Enter” key.
2
2 2
2
2 Enter numerical value to be set and press the
“Enter” key.
Display subnet mask after change (*).
The setting procedure for each item will be explained. For the basic pro\
cedure,...")
![Page 24
-24
Password Setting
([5]Password)
Carrying out security protection using password.1
1 1
1
1 Enter “5” and press the “Enter” key.
2
2 2
2
2 Enter password and press the “Enter” key.
Display set password (*).
Note
•Password can be up to 8 characters.
• You can input the characters below :
a-z, A-Z, 0-9, -, _
• In the def ault state, the password is not set.
RS-232C Baud Rate Set-
ting ([6]RS-232C Baud Rate)
Setting of baud rate for RS-232C terminals.
1
1 1
1
1 Enter “6” and press the “Enter” key.
2
2 2...](http://img.usermanuals.tech/thumb/68/96210/w64_sharp-xg-mb67xl-technical_d-23.png "Page 24
-24
Password Setting
([5]Password)
Carrying out security protection using password.1
1 1
1
1 Enter “5” and press the “Enter” key.
2
2 2
2
2 Enter password and press the “Enter” key.
Display set password (*).
Note
•Password can be up to 8 characters.
• You can input the characters below :
a-z, A-Z, 0-9, -, _
• In the def ault state, the password is not set.
RS-232C Baud Rate Set-
ting ([6]RS-232C Baud Rate)
Setting of baud rate for RS-232C terminals.
1
1 1
1
1 Enter “6” and press the “Enter” key.
2
2 2...")
![Page 25
-25
Disconnecting All Connec-
tions ([D]Disconnect All)
It is possible to disconnect all the TCP/IP connec-
tions currently recognized by the projector. Even if
the COM Redirect port is fixed in the Busy status
due to a problem, it is possible to force the Ready
status back by carrying out this disconnection.1
1 1
1
1 Enter “d” and press the “Enter” key.
2
2 2
2
2 Enter “y” and press the “Enter” key.
Note
•If Disconnect All is performed, the connection to
the projector via network will be forcibly...](http://img.usermanuals.tech/thumb/68/96210/w64_sharp-xg-mb67xl-technical_d-24.png "Page 25
-25
Disconnecting All Connec-
tions ([D]Disconnect All)
It is possible to disconnect all the TCP/IP connec-
tions currently recognized by the projector. Even if
the COM Redirect port is fixed in the Busy status
due to a problem, it is possible to force the Ready
status back by carrying out this disconnection.1
1 1
1
1 Enter “d” and press the “Enter” key.
2
2 2
2
2 Enter “y” and press the “Enter” key.
Note
•If Disconnect All is performed, the connection to
the projector via network will be forcibly...")
![Page 26
-26
Carrying out Network Ping
Test
(ADVANCED[5]Network Ping Test)
It is possible to confirm that a network connection
between the projector and a computer etc. is work-
ing normally.1
1 1
1
1 Enter “5” and press the “Enter” key.
2
2 2
2
2 Enter IP address of device to be tested and
press the “Enter” key.
Display entered IP address (*1).
Display test result (*2).
Note
•If the “Enter” key is pressed without entering an
IP address, the Ping destination IP address used
previously is entered.
• If there is a...](http://img.usermanuals.tech/thumb/68/96210/w64_sharp-xg-mb67xl-technical_d-25.png "Page 26
-26
Carrying out Network Ping
Test
(ADVANCED[5]Network Ping Test)
It is possible to confirm that a network connection
between the projector and a computer etc. is work-
ing normally.1
1 1
1
1 Enter “5” and press the “Enter” key.
2
2 2
2
2 Enter IP address of device to be tested and
press the “Enter” key.
Display entered IP address (*1).
Display test result (*2).
Note
•If the “Enter” key is pressed without entering an
IP address, the Ping destination IP address used
previously is entered.
• If there is a...")
![Page 27
-27
Setting of Search Port
(ADVANCED[0]Search Port)
Sets the port number used when searching for the
projector from the network.1
1 1
1
1 Enter “0” and press the “Enter” key.
2
2 2
2
2 Enter numerical value and press the “Enter” key.
Display set numerical value (*).
Note
•Set according to need. Nor mally, use with the fac-
tory default setting.
Return to Default Settings
(ADVANCED[!]Restore Default
Setting)
Returns all menu setting values to the default state.
1
1 1
1
1 Enter “!” and press the “Enter”...](http://img.usermanuals.tech/thumb/68/96210/w64_sharp-xg-mb67xl-technical_d-26.png "Page 27
-27
Setting of Search Port
(ADVANCED[0]Search Port)
Sets the port number used when searching for the
projector from the network.1
1 1
1
1 Enter “0” and press the “Enter” key.
2
2 2
2
2 Enter numerical value and press the “Enter” key.
Display set numerical value (*).
Note
•Set according to need. Nor mally, use with the fac-
tory default setting.
Return to Default Settings
(ADVANCED[!]Restore Default
Setting)
Returns all menu setting values to the default state.
1
1 1
1
1 Enter “!” and press the “Enter”...")
-31 Troubleshooting \ Take the following steps for checking the network settings for the computer. 1. Open a command prompt (MS-DOS Prompt). •In the case of Windows ® 98 or 98SE: click “START” ➔ “Programs” ➔ “MS-DOS Prompt” in order. • In the case of Windows ® Me: click “START” ➔ “Programs” ➔ “Accessories” ➔ “MS-DOS Prompt” in order. • In the case of Windows ® 2000: click “START” ➔ “Programs” ➔ “Accessories” ➔ “Command Prompt” in order. • In the case of Windows ® XP: click “START” ➔ “All Programs” ➔ “Accessories” ➔ “Command Prompt” in order. 2. After launching the command prompt (MS-DOS Prompt), enter the command \ “ipconfig”, and press the “Enter” key. Note •Communication may not be established even after carrying out the network settings for the computer. In such cases, restart your computer. C:\>ipconfig Note • Usage examples of ipconfig C:\>ipconfig /? displays how to use “ipconfig.exe”. C:\>ipconfig displays the set IP address, subnet mask and default gateway. C:\>ipconfig /all displays all the setting information related to TCP/IP. 3. To return to the Windows® screen, enter “exit” and press the “Enter” key.
-32 \Check if the “TCP/IP” protocol is operating correctly using the “PING” command. Also, check if an IP address is set. 1. Open a command prompt (MS-DOS Prompt). •In the case of Windows ® 98 or 98SE: click “START” ➔ “Programs” ➔ “MS-DOS Prompt” in order. • In the case of Windows ® Me: click “START” ➔ “Programs” ➔ “Accessories” ➔ “MS-DOS Prompt” in order. • In the case of Windows ® 2000: click “START” ➔ “Programs” ➔ “Accessories” ➔ “Command Prompt” in order. • In the case of Windows ® XP: click “START” ➔ “All Programs” ➔ “Accessories” ➔ “Command Prompt” in order. 2. After launching the command prompt (MS-DOS Prompt) enter a command “PING”. Entry example C:\>Ping XXX.XXX.XXX.XXX “XXX.XXX.XXX.XXX” should be entered with an IP address to be connected to, such as the projector. 3. When connecting normally, the display will be as follows. (The screen may be slightly different depending on the OS type). when the IP address connected to is “192.168.150.2” 4. When a command cannot be sent, “Request time out” will be displayed.Check the network setting again. If communication can still not be established properly, contact your network administrator. 5. To return to the Windows ® screen, enter “exit” and then press the “Enter” key. A connection cannot be made because you have forgotten your user name or your password. \ Initialize the settings. (See page 51 of the projector’s operation manual.) \ After the initialization, carry out setting again. Troubleshooting