Sharp Xg Mb67xl Projector Technical Manual

MODEL
XG-MB67X-L
MULTIMEDIA PROJECTOR
SETUP MANUAL
Connecting Pin Assignments............................ 2
RS-232C Specifications and  Commands.......... 3
Setting up the Projector Network Environment ...7
1. Connecting the Projector to  a Computer............ 8
2. Setting an IP Address  for the Computer ............ 9
3. Setting up a Network Connection for the Projector ..11
Controlling the Projector  via LAN.................... 13
Controlling the Projector Using Internet Explorer
(Version 5.0  or...

-2
RS-232C Terminal:9-pin mini DIN female connector
Pin No. Signal Name I/O Reference
1 Not connected
2R DReceive Data Input Connected to internal circuit
3S DSend Data Output Connected to internal circuit
4 Not connected
5S GSignal Ground Connected to internal circuit
6 Not connected
7R SRequest to Send Connected to CS in internal circuit
8C SClear to Send Connected to RS in internal circuit
9 Not connected
RS-232C Terminal: 9-pin D-sub male connector of the DIN-D-sub RS-232C adaptor
Pin No. Signal Name...

-3
Computer control
A computer can be used to control the projector by connecting an RS-232C serial control cable (cross type,
commercially available) to the projector. (See page 26 of the projector’s operation manual for connection.)
Communication conditions
Set the serial port settings of the computer to match that of the table.\
Signal format: Conforms to RS-232C standard. Parity bit: None
Baud rate*: 9,600 bps / 115,200 bps Stop bit: 1 bit
Data length: 8 bits Flow control: None
*Set the projector’s...

-4
RS-232C Specifications and Commands
Commands
Example: When turning on the projector, make the following setting.
→
←POWR _ 1__OK
Projector
Computer
Power Off
Power On
Power Status
Projector Condition
Lamp Status
Lamp Power Status
Lamp Quantity
Lamp Usage Time (Hour)
Lamp Life (Percentage)
Model Name Check
Model Name Check
Projector Name Setting 1 
(First four characters) *1
Projector Name Setting 2 
(Middle four characters) *1
Projector Name Setting 3
 (Last four characters) *1
Projector Name Check...

-5
RS-232C Specifications and Commands
INPUT 1 Picture Mode : Presentation
INPUT 1 Picture Mode : Movie
INPUT 1 Picture Mode : Game
INPUT 1 Picture Mode : sRGB
INPUT 1 Contrast (
30 –  30)
INPUT 1 Bright ( 
30 –  30)
INPUT 1 Color ( 
30 –  30)
INPUT 1 Tint ( 
30 –  30)
INPUT 1 Red ( 
30 –  30)
INPUT 1 Blue ( 
30 –  30)
INPUT 1 Sharp ( 
30 –  30)
INPUT 1 CLR Temp *2
INPUT 1 Bright Boost (0 – 2)
INPUT 1 Progressive : 2D
INPUT 1 Progressive : 3D
INPUT 1 Progressive : Film Mode
INPUT 1 Signal Type :...

-6
RS-232C Specifications and Commands
INPUT 4 Sharp (
30 –  30)
INPUT 4 CLR Temp *2
INPUT 4 Bright Boost (0 – 2)
INPUT 4 Progressive : 2D
INPUT 4 Progressive : 3D
INPUT 4 Progressive : Film Mode
Clock ( 
150 –  150)
Phase ( 
30 –  30)
H-Position ( 
150 –  150)
V -Position ( 
60 –  60)
Fine Sync Adjustment Reset
Auto Sync : Off
Auto Sync : On
Internal Speaker : Off
Internal Speaker : On
Image Shift ( 
96 –  96 )
OSD Display : Off
OSD Display : On
Video System Selection : AUTO
Video System Selection...

-7
Page 8
1.Connecting the projector to a computer
Setting up the Projector Network Environment
This section describes the basic procedure for using the projector via the network.
If the network is already constructed, the projector’s network settings may need to be changed. Please
consult your network administrator for assistance with these settings.
You can make network settings both on the projector and on the computer. The following procedure is for
making settings on the computer.
Network settings...

-8
Setting up the Projector Network Environment
1. Connecting the Pro-
jector to a Computer
Establishing a one-to-one connection from the
projector to a computer. Using a LAN cable
(Category 5, cross-over type) you can config-
ure the projector via the computer.
1Disconnect the computer’s LAN
cable from the existing network.
2Connect a LAN cable (a UTP
cable, Category 5, cross-over
type) to the projector’s LAN ter-
minal and connect the other end
of the cable to the computer’s
LAN terminal.
3Plug the...

-9
Setting up the Projector Network Environment
2. Setting an IP Address
for the Computer
The following describes how to make settings
in Windows® XP  (Professional or Home
Edition).
1Log on the network using the
administrator’s account for the
computer.
2Click  “Start”, and click “Control
P anel”.
3Click “Network and Internet Con-
nections”, and click “Network
Connections” in the new win-
dow.
• This manual uses examples to explain
the operations in Category View. If you
are using Classic View,...

-10
Setting up the Projector Network Environment
1
2
After confirming or setting, proceed to “3. Setting up Network Connection for the
Projector” .
5Click “Internet Protocol (TCP/IP)”,
and click the “Properties” button.
6Confirm or change an IP address
for the setup computer.
1 Confirm and note the current IP ad-
dress, Subnet mask and Default
gateway.
Make sure to note the current IP
address, Subnet mask and Default
gateway as you will be required to re-
set them later.
2 Set  temporarily as follows :...