Sharp Xg Mb65x Projector User Manual

27
Basic
Operation
Turning the Projector On/Off
Remove the lens cap and press
SSTANDBY/ON on the projector or
fON on the remote control.
• When System Lock is set, the keycode input box
appears. To cancel the keycode setting, input the
keycode that you have already set. See page 44
for details.
•About the Lamp Indicator
The lamp indicator illuminates to indicate the status of the
lamp.
Green: The lamp is on.
Blinking in green:The lamp is warming up or shut-
ting down.
Red: The lamp is shut down...

28
About the Setup Guide
After turning on the projector, the Setup
Guide screen appears to assist you with
projector setup.
Press TENTER to exit the Setup Guide
screen.
Guidance items
1 FOCUS
2 HEIGHT ADJUST
3 ZOOM
STANDBY/ON
button
ENTER button
1 Adjusting the Focus
You can adjust the focus with the focus
ring on the projector.
Image Projection
Rotate the focus ring to adjust the fo-
cus while watching the projected image.
Setup Guide screen
• The Setup Guide screen automatically high-
lights the items...

29
Basic
Operation
3 Adjusting the Height
The height of the projector can be ad-
justed using the adjustment feet at the
front and rear of the projector.
When the screen is above the projec-
tor, the projection image can be made
higher by adjusting the projector.
1
2
3
• Do not apply too much pressure on the pro-
jector when the front adjustment foot comes
out.
• When lowering the projector, be careful not to
get your fingers caught in the area between
the adjustment foot and the projector.
• Hold the...

30
Image Projection (Continued)
Displaying the Black Screen
and Turning off the Sound
Temporarily
Adjusting the Volume
Switching the Input Mode
PressCINPUT 1, CINPUT 2,
DINPUT 3 or EINPUT 4 on the remote
control to select the input mode.
• When pressing INPUT (P/R) on the projector,
input mode switches in the following order:
INPUT1 INPUT2 INPUT3 INPUT4.
• When “Auto Search” is set to “On”, INPUT (P/
R) on the projector functions as the Auto Search
buttons. (See page 43.)
Select the appropriate input...

31
Basic
Operation
0 KeystoneADJ. END
Correcting Trapezoidal
Distortion
When the image is projected either from
the top or from the bottom towards the
screen at an angle, the image becomes
distorted trapezoidally. The function for
correcting trapezoidal distortion is
called Keystone Correction.
• The Keystone Correction can be adjusted up
to an angle of approximately ±13 degrees and
the screen can also be set up to an angle of
approximately ±13 degrees (when the resize
mode is set to “NORMAL” (see page...

32
Image Projection (Continued)
Resize Mode
This function allows you to modify or customize the resize mode to enhance the input image. De-
pending on the input signal, you can choose “NORMAL”, “BORDER” or “STRETCH” image.
Press HRESIZE.• See page 41 for setting on menu screen.
Computer
Input Signal
NORMALOutput screen image
Computer Image type BORDER STRETCH
SXGA
(1280K1024)
1280K720
4:3 aspect ratio
5:4 aspect ratio
16:9 aspect
ratio
* Mode for projecting an image with the original
aspect ratio without...

33
Basic
Operation
VIDEO
•“STRETCH” is fixed when 540P, 720P or 1080I signals are entered.
: Cutout area on which images cannot be projected.
: Area on which the image is not included in the original signals.Input Signal
DVD / Video Image typeOutput screen image
NORMAL
BORDERSTRETCH
480I, 480P, 576I,
576P, NTSC, PAL,
SECAM
540P, 720P, 1080I
4:3 aspect ratio
Letter box
Squeezed 16:9 image
Squeezed 4:3 image
16:9 aspect ratio
16:9 aspect ratio
(4:3 aspect ratio in
16:9 screen)
* Mode for projecting an...

34
Auto Sync
(Auto Sync Adjustment)
Operating with the Remote Control
Freezing a Moving Image
• When the optimum image cannot be achieved
with Auto Sync adjustment, use the help menu
for manual adjustments. (See page 46.)
Auto Sync function works when detect-
ing input signal after the projector turns
on.
Press FAUTO SYNC to manually ad-
just with Auto Sync function.
Press NFREEZE.
• The projected image is frozen.
Press NFREEZE again to return
to the moving image from the cur-
rently connected device.
1...

35
Useful
Features
The following shows the items that can be set in the projector.
Menu Items
“Screen adjustment (SCR-ADJ)” menu
INPUT 1 (Component)/INPUT 2
(Component)/INPUT 3/INPUT 4 INPUT 1 (RGB)/INPUT2 (RGB)
“Picture” menu
Picture
Picture Mode
Contrast 0
0
0
0
K 8500SCR - ADJ PRJ - ADJ Help
BrightRedBlue
1CLR TempBright Boost
Lamp SettingStandard
Bright
Reset
SEL./ADJ. ENTER END
Picture
Picture Mode
Contrast 0
0
0
0
K 8500SCR - ADJ PRJ - ADJ Help
BrightColorTint0 Sharp
1CLR TempBright Boost...

36
“Projection adjustment (PRJ-ADJ)” menu
Picture
Auto SearchSCR - ADJPRJ - ADJHelp
Auto Sync
Auto Power Off
System Sound
System Lock
h On On
On
On
SEL./ADJ. ENTER END0 Lamp Timer(Life) 100%
Speaker OnRS-232C 9600 bpsFan Mode Normal
Picture
There is no picture or audioSCR - ADJ PRJ - ADJHelp
Vertical stripes or flickering image appear
Data image is not centered
Color is faded or poor
Picture is dark
The image is distorted
Reset all adjustments to default settings
SEL. ENTER END
Main menu Sub menuPRJ -...