Sharp Xg Mb55x Projector User Manual
Have a look at the manual Sharp Xg Mb55x Projector User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 615 Sharp manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
47 Appendix Cleaning the lensUse a commercially available blower or lens cleaning paper (for glasses and camera lenses) for cleaning the lens. Do not use any liquid type cleaning agents, as they may wear off the coating film on the surface of the lens. As the surface of the lens can easily get damaged, be sure not to scrape or hit the lens. Cleaning the exhaust and intake ventsUse a vacuum cleaner to clean dust from the exhaust vent and the intake vent. Cleaning the projectorEnsure that you have unplugged the power cord before cleaning the projector. The cabinet as well as the operation panel is made of plastic. Avoid using benzene or thinner, as these can damage the finish on the cabinet. Do not use volatile agents such as insecticides on the projector. Do not attach rubber or plastic items to the projector for long periods. The effects of some of the agents in the plastic may cause damage to the quality or finish of the projector. Wipe off dirt gently with a soft flannel cloth. When the dirt is hard to remove, soak a cloth in a mild detergent diluted with water, wring the cloth well and then wipe the projector. Strong cleaning detergents may discolor, warp or damage the coating on the projector. Make sure to test on a small, inconspicuous area on the projector before use. Maintenance Thinner • If you want to clean the air vents during pro- jector operation, be sure to press SSTANDBY/ON on the projector or eSTANDBY on the remote control and put the projector into standby mode. After the cooling fan has stopped, clean the vents. Info Wax Mild detergent Mild detergent diluted with water
48 Maintenance Indicators About the lamp indicator When the remaining lamp life becomes 5% or less, (yellow) and “Change The Lamp” will be displayed on the screen. When the percentage becomes 0%, it will change to (red), the lamp will automatically turn off and then the projector will automatically enter standby mode. At this time, the lamp indicator will illuminate in red. If you try to turn on the projector a fourth time without replacing the lamp, the projector will not turn on. About the temperature warning indicator If the temperature inside the projector increases, due to blockage of the air vents, or the setting location, “” will illuminate in the lower left corner of the picture. If the temperature keeps on rising, the lamp will turn off and the temperature warning indicator will blink, the cooling fan will run, and then the projec- tor will enter standby mode. After “ ” appears, be sure to perform the measures described on page 49. Lamp indicator The warning lights (power indicator, lamp indicator and temperature warning indicator) on the projector indicate problems inside the projector. If a problem occurs, either the temperature warning indicator or the lamp indicator will illuminate red, and the projector will enter standby mode. After the projector has entered standby mode, follow the procedures given below. Temperature warning indicator Power indicator Lamp indicatorRed on Power indicator Indicators on the Projector Green on Normal (Standby) Normal (Power on) Green on Green blinks Normal The lamp is warming up or shutting down. Temperature warning indicator Off Red onNormal The internal temperature is abnormally high. (See page 49.) Red blinksAbnormal (See page 49.) Red on The lamp is shut down abnormally or requires to be changed. (See page 49.) Green blinksNormal (Cooling) Top View
49 Appendix • If the temperature warning indicator illuminates, and the projector enters standby mode, follow the possible solutions above and then wait until the projector has cooled down completely before plug- ging in the power cord and turning the power back on. (At least 10 minutes.) • If the power is turned off for a brief moment due to power outage or some other cause while using the projector, and the power supply recovers immediately after that, the lamp indicator will illumi- nate in red and the lamp may not be lit. In this case, unplug the power cord from the AC outlet, replace the power cord in the AC outlet and then turn the power on again. • The cooling fan keeps the internal temperature of the projector constant and this function is con- trolled automatically. The sound of the cooling fan may change during operation because the fan speed may change and this is not a malfunction. • Do not unplug the power cord after the projector has entered standby mode and while the cooling fan is running. The cooling fan runs for about 90 seconds. Maintenance indicator Problem The internal temperature is abnormally high. The lamp does not illuminate. Time to change the lamp. The lamp does not illuminate. The power indicator blinks in red when the projector is on.Cause • Blocked air intake • Cooling fan breakdown • Internal circuit failure • Clogged air intake • The lamp is shut down abnormally. • Remaining lamp life becomes 5% or less. • Burnt-out lamp • Lamp circuit failure • The lamp unit cover is open.Possible Solution • Relocate the projector to an area with proper ventilation. (see page 8) • Take the projector to your nearest Sharp Authorized Projector Dealer or Service Center (see page 61) for repair. • Disconnect the power cord from the AC outlet, and then connect it again. • Carefully replace the lamp. (See page 51.) • Take the projector to your nearest Sharp Authorized Projector Dealer or Service Center (see page 61) for repair. • Please exercise care when replacing the lamp. • Securely install the cover. • If the power indicator blinks in red even when the lamp unit cover is securely installed, contact your nearest Sharp Authorized Projector Dealer or Service Center (see page 61) for advice.Abnormal Red on (Standby) Red on Red on (Standby) Red blinks Tempera- ture warning indicator Lamp indicator Power indicatorNormal Off Green on (Green blinks when the lamp is warming up or turning off.) Green on/ Red on Green blinks (Cooling) Info
50 Regarding the Lamp LampIt is recommended that the lamp (sold separately) be replaced when the remaining lamp life becomes 5% or less, or when you notice a significant deterioration in the picture and color quality. The lamp life (percentage) can be checked with the on-screen display. (see page 44) Purchase a replacement lamp of type AN-XR20LP/AN-XR10LP from your place of purchase, nearest Sharp Authorized Projector Dealer or Service Center. Caution Concerning the LampThis projector utilizes a pressurized mercury lamp. A loud sound may indicate lamp failure. Lamp failure can be attributed to numerous sources such as: excessive shock, improper cooling, surface scratches or deterioration of the lamp due to a lapse of usage time. The period of time up to failure largely varies depending on the individual lamp and/or the condition and the frequency of use. It is important to note that failure can often result in the bulb cracking. When the lamp replacement indicator and on-screen display icon are illuminated, it is recommended that the lamp be replaced with a new one immediately, even if the lamp appears to be operating normally. Should the lamp break, there is also a possibility that glass particles may spread inside of the projector. In such a case, it is recommended you contact your nearest Sharp Authorized Projector Dealer or Service Center to assure safe operation. Should the lamp break, the glass particles may spread inside the lamp cage or gas contained in the lamp may be vented into the room from the exhaust vent. Because the gas in this lamp includes mercury, ventilate the room well if the lamp breaks and avoid all exposure to the released gas. In case of exposure to the gas, consult a doctor as soon as possible. Replacing the Lamp Caution • Do not remove the lamp unit from the projector right after use. The lamp will be very hot and may cause burn or injury. Carefully change the lamp by following the instructions described in this section. * If you wish, you may have the lamp replaced at your nearest Sharp Authorized Projector Dealer or Service Center. * If the new lamp does not light after replacement, take your projector to the nearest Sharp Authorized Projector Dealer or Service Center for repair. IMPORTANT NOTE TO U.S. CUSTOMERS: The lamp included with this projector is backed by a 90-day parts and labor limited warranty. All service of this projector under warranty, including lamp replacement, must be obtained through a Sharp Authorized Projector Dealer or Service Center. For the name of the nearest Sharp Authorized Projector Dealer or Service Center, please call toll-free: 1-888-GO-SHARP (1-888-467-4277). Hg LAMP CONTAINS MERCURY For State Lamp Disposal Information www.lamprecycle.org or 1-800-BE-SHARP U.S.A. ONLY
51 Appendix Removing and Installing the Lamp Unit • Make sure that you remove the lamp unit by the handle. Do not touch the glass surface of the lamp unit or the inside of the projector. • To avoid injury to yourself and damage to the lamp, be sure to carefully follow the steps below. • Do not loosen other screws except for the lamp unit cover and lamp unit. Press SSTANDBY/ON on the pro- jector or eSTANDBY on the re- mote control to put the projector into standby mode. • Wait until the cooling fan stops. Warning! • Do not remove the lamp unit from the projec- tor right after use. The lamp and parts around the lamp will be very hot and may cause burns or injury. Disconnect the power cord.• Unplug the power cord from the AC socket. • Leave the lamp until it has fully cooled down (about 1 hour). Remove the lamp unit cover.• Turn the projector over. Loosen the user service screw (1) that secures the lamp unit cover. Remove the lamp unit cover (2). 1 2 Lamp unit AN-XR20LP (for XG-MB55X/ XR-20X/XR-20S) AN-XR10LP (for XR-10X/XR-10S) Info Optional accessory AC socket User service screw (for lamp unit cover) 1 2 3 STANDBY/ON button
52 Regarding the Lamp (Continued) Remove the lamp unit.• Loosen the securing screws from the lamp unit. Hold the lamp unit by the handle and pull it in the direction of the arrow. At this time, keep the lamp unit horizontal and do not tilt it. Resetting the Lamp Timer Reset the lamp timer after replacing the lamp. Insert the new lamp unit.• Press the lamp unit firmly into the lamp unit compartment. Fasten the securing screws. Replace the lamp unit cover.• Align the tab on the lamp unit cover (1)and place it while pressing the tab (2) to close it. Then tighten the user ser- vice screw to secure the lamp unit cover. 4 5 6 Connect the power cord.• Plug the power cord into the AC socket of the projector. Reset the lamp timer.• While simultaneously holding down UMENU/HELP, TENTER and R on the projector, press SSTANDBY/ON on the projector. • “LAMP 0000H” is displayed, indicating that the lamp timer is reset. • Make sure to reset the lamp timer only when replacing the lamp. If you reset the lamp timer and continue to use the same lamp, this may cause the lamp to become damaged or ex- plode. 1 2 Info AC socket Securing screwsHandle ENTER button MENU/HELP button R button • If the lamp unit and lamp unit cover are not correctly installed, the power will not turn on, even if the power cord is con- nected to the projector. Info 2 1 STANDBY/ON button
53 Appendix Connecting Pin Assignments COMPUTER-RGB Input/Output COMPUTER-RGB/COMPONENT INPUT1, 2 and COMPUTER-RGB/COMPONENT OUTPUT Terminals: 15-pin mini D-sub female connector 1. Video input (red) 2. Video input (green/sync on green) 3. Video input (blue) 4. Not connected 5. Not connected 6. Earth (red) 7. Earth (green/sync on green) 8. Earth (blue) 9. Not connected 10. GND 11. Not connected 12. Bi-directional data 13. Horizontal sync signal: TTL level 14. Vertical sync signal: TTL level 15. Data clock RS-232C Terminal: 9-pin mini DIN female connectorComponent Input/Output 510 15 1 11 6 1. PR (CR) 2. Y 3. PB (CB) 4. Not connected 5. Not connected 6. Earth (PR) 7. Earth (Y) 8. Earth (PB) 9. Not connected 10. Not connected 11. Not connected 12. Not connected 13. Not connected 14. Not connected 15. Not connected RD SD SG RS CS Signal Name 8 9 6 5 2143 7Pin No. 1. 2. 3. 4. 5. 6. 7. 8. 9.I/O Reference Not connected Connected to internal circuit Connected to internal circuit Not connected Connected to internal circuit Not connected Connected to CS in internal circuit Connected to RS in internal circuit Not connected Receive Data Send Data Signal Ground Request to Send Clear to SendInput Output RS-232C Terminal: 9-pin D-sub male connector of the DIN-D-sub RS-232C adaptor* (optional accessory: AN-A1RS) RD SD SG RS CS Signal Name Pin No. 1. 2. 3. 4. 5. 6. 7. 8. 9.I/O Reference Not connected Connected to internal circuit Connected to internal circuit Not connected Connected to internal circuit Not connected Connected to CS in internal circuit Connected to RS in internal circuit Not connected Receive Data Send Data Signal Ground Request to Send Clear to SendInput Output 15 69 CD RD SD ER SG DR RS CS CI Signal Pin No. 1. 2. 3. 4. 5. 6. 7. 8. 9. RS-232C Cable recommended connection: 9-pin D-sub female connector CD RD SD ER SG DR RS CS CI Signal Pin No. 1. 2. 3. 4. 5. 6. 7. 8. 9.51 96 •Depending on the controlling device used, it may be necessary to connect Pin 4 and Pin 6 on the controlling device (e.g. computer). Note Projector Pin No. 4 5 6Computer Pin No. 4 5 6 * This adaptor is only supplied with XG-MB55X.
54 RS-232C Specifications and Command Settings Computer control A computer can be used to control the projector by connecting an RS-232C serial control cable (cross type, sold separately) to the projector. (See page 26 for connection.) Communication conditions Set the serial port settings of the computer to match that of the table. Signal format: Conforms to RS-232C standard. Parity bit: None Baud rate: * 9,600 bps/115,200 bps Stop bit: 1 bit Data length: 8 bits Flow control: None * Set the projectors baud rate to the same rate as used by the computer. Basic format Commands from the computer are sent in the following order: command, parameter, and return code. After the projector processes the command from the computer, it sends a response code to the computer. • When controlling the projector using RS-232C commands from a computer, wait for at least 30 seconds after the power has been turned on, and then transmit the commands. • When more than one code is being sent, send each command only after the response code for the previous command from the projector is verified. • “POWR????” “TABN _ _ _ 1” “TLPS _ _ _ 1” “TPOW _ _ _ 1” “TLPN _ _ _ 1” “TLTT _ _ _ 1” “TLTL _ _ _ 1” “TNAM _ _ _ 1” “MNRD _ _ _ 1” “PJN0 _ _ _ 1” When the projector receives a command shown above: * The on-screen display will not disappear. * The “Auto Power Off” timer will not be reset. Info Return code (0DH)C1 C2 C3 C4 P1 P2 P3 P4 Response code format Normal response Problem response (communication error or incorrect command) O K E R R Command 4-digitParameter 4-digit Command format Return code (0DH)Return code (0DH) • If an underbar (_) appears in the parameter column, enter a space. • If an asterisk (*) appears in the parameter column, enter a value in the range indicated in brackets under Control Contents. *1 For setting the projector name, send the commands in the order of PJN1, PJN2 and PJN3. *2 Parameters of CLR Temp settings are as follows. Note CLR Temp Parameter CLR Temp Parameter 5500K _0 5 5 8500K _0 8 5 6500K _0 6 5 9300K _0 9 3 7500K _0 7 5 10500K _1 0 5
55 Appendix Power Off Power On Power Status Projector Condition Lamp Status Lamp Power Status Lamp Quantity Lamp Usage Time (Hour) Lamp Life (Percentage) Model Name Check Model Name Check Projector Name Setting 1 (First four characters) *1 Projector Name Setting 2 (Middle four characters) *1 Projector Name Setting 3 (Last four characters) *1 Projector Name Check INPUT 1 (RGB1) INPUT 2 (RGB2) INPUT RGB Check INPUT 3 (Video1) INPUT 4 (Video2) INPUT Video Check INPUT Mode Check INPUT Check INPUT 1 Adjustment Reset INPUT 2 Adjustment Reset INPUT 3 Adjustment Reset INPUT 4 Adjustment Reset All Reset Volume (0 – 60) Volume up / down (10 – 10) Keystone (127 – 127 (XGA) / 100 – 100 (SVGA))AV Mute Off AV Mute On Freeze Off Freeze On Auto Sync Start INPUT 1 Resize : Normal INPUT 1 Resize : Stretch INPUT 1 Resize : Border INPUT 2 Resize : Normal INPUT 2 Resize : Stretch INPUT 2 Resize : Border INPUT 3 Resize : Normal INPUT 3 Resize : Stretch INPUT 3 Resize : Border INPUT 4 Resize : Normal INPUT 4 Resize : Stretch INPUT 4 Resize : Border INPUT 1 Picture Mode : StandardOK or ERR OK 1 0 : Normal, 1 : Temp High, 8 : Lamp Life 5% or less, 16 : Lamp Burnt-out, 32 : Lamp Ignition Failure 0 : Off, 1 : On, 2 : Retry, 3 : Waiting, 4 : Lamp Error1 : On, 2 : Cooling, 3 : Shutting Down 1 0 – 9999 (Integer) 0% – 100% (Integer) XGMB55X / XR10S / XR10X / XR20S / XR20X XG-MB55X / XR-10S / XR-10X / XR-20S / XR-20X OK or ERR OK or ERR OK or ERR Projector Name OK or ERR OK or ERR 1 : RGB1 (INPUT1), 2 : RGB2 (INPUT2), ERR OK or ERR OK or ERR 1 : Video1 (INPUT3), 2 : Video2 (INPUT4), ERR1 : RGB, 2 : Video1 : INPUT1, 2 : INPUT2, 3 : INPUT3, 4 : INPUT4OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERROK OK or ERR 0 0 : Normal, 1 : Temp High, 2 : Fan Error, 4 : Lamp Cover Open, 8 : Lamp Life 5% or less, 16 : Lamp Burnt-out, 32 : Lamp Ignition Failure, 64 : Temp Abnormally High 0 : Off, 4 : Lamp Error 0 : Standby ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR P P P T T T T T T T M P P P P I I I I I I I I R R V V A V V K I I F F A R R R R R R R R R R R R RO O O A L P L L L N N J J J J R R R V V V M C A B A B L O O E M M R R D A A A B B B A A A B B B AW W W B P O P T T A R N N N N G G G E E E O H R R R R R L U Y B B E E J S S S S S S S S S S S S PR R R N S W N T L M D 1 2 3 0 B B B D D D D K E E E E E A D S K K Z Z S R R R R R R V V V V V V S_ _ ? _ _ _ _ _ _ _ _ * * * _ _ _ ? _ _ ? ? ? _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ __ _ ? _ _ _ _ _ _ _ _ * * * _ _ _ ? _ _ ? ? ? _ _ _ _ _ _ * * _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ __ _ ? _ _ _ _ _ _ _ _ * * * _ _ _ ? _ _ ? ? ? _ _ _ _ _ * * * _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 10 1 ? 1 1 1 1 1 1 1 1 * * * 1 1 2 ? 1 2 ? ? ? 1 1 1 1 1 * * * 0 1 0 1 1 1 2 6 1 2 6 1 2 3 1 2 3 0 CONTROL CONTENTS Power ONStandby mode (or 40-second startup time) COMMAND PARAMETERRETURN → ←POWR_1 __OK Projector Computer Commands Example: When turning on the projector, make the following setting.
56 INPUT 1 Picture Mode : Presentation INPUT 1 Picture Mode : Movie INPUT 1 Picture Mode : Game INPUT 1 Picture Mode : sRGB INPUT 1 Contrast (30 – 30) INPUT 1 Bright (30 – 30) INPUT 1 Color (30 – 30) INPUT 1 Tint (30 – 30) INPUT 1 Red (30 – 30) INPUT 1 Blue (30 – 30) INPUT 1 Sharp (30 – 30) INPUT 1 CLR Temp *2 INPUT 1 Bright Boost (0 – 2) INPUT 1 Progressive : 2D INPUT 1 Progressive : 3D INPUT 1 Progressive : Fim Mode INPUT 1 Signal Type : Auto INPUT 1 Signal Type : RGB INPUT 1 Signal Type : Component INPUT 2 Picture Mode : Standard INPUT 2 Picture Mode : Presentation INPUT 2 Picture Mode : Movie INPUT 2 Picture Mode : Game INPUT 2 Picture Mode : sRGB INPUT 2 Contrast (30 – 30) INPUT 2 Bright (30 – 30) INPUT 2 Color (30 – 30) INPUT 2 Tint (30 – 30) INPUT 2 Red (30 – 30) INPUT 2 Blue (30 – 30) INPUT 2 Sharp (30 – 30) INPUT 2 CLR Temp *2 INPUT 2 Bright Boost (0 – 2) INPUT 2 Progressive : 2D INPUT 2 Progressive : 3D INPUT 2 Progressive : Flm Mode INPUT 2 Signal Type : Auto INPUT 2 Signal Type : RGB INPUT 2 Signal Type : Component INPUT 3 Picture Mode : Standard INPUT 3 Picture Mode : Presentation INPUT 3 Picture Mode : Movie INPUT 3 Picture Mode : Game INPUT 3 Contrast (30 – 30) INPUT 3 Bright (30 – 30) INPUT 3 Color (30 – 30) INPUT 3 Tint (30 – 30) INPUT 3 Sharp (30 – 30) INPUT 3 CLR Temp *2 INPUT 3 Bright Boost (0 – 2) INPUT 3 Progressive : 2D INPUT 3 Progressive : 3D INPUT 3 Progressive : Film Mode INPUT 4 Picture Mode : Standard INPUT 4 Picture Mode : Presentation INPUT 4 Picture Mode : Movie INPUT 4 Picture Mode : Game INPUT 4 Contrast (30 – 30) INPUT 4 Bright (30 – 30) INPUT 4 Color (30 – 30) INPUT 4 Tint (30 – 30)OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERRERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR ERR R R R R R R R R R R R R R R R R I I I R R R R R R R R R R R R R R R R R I I I V V V V V V V V V V V V V V V V V V V V V VA A A A A A A A A A A A A A A A A A A B B B B B B B B B B B B B B B B B B B B A A A A A A A A A A A A A A B B B B B B B BP P P P P B C T R B S C W I I I S S S P P P P P P B C T R B S C W I I I S S S P P P P P B C T S C W I I I P P P P P B C TS S S S I R O I D E H T E P P P I I I S S S S S I R O I D E H T E P P P I I I S S S S I R O I H T E P P P S S S S I R O I_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ __ _ _ _ * * * * * * * * _ _ _ _ _ _ _ _ _ _ _ _ * * * * * * * * _ _ _ _ _ _ _ _ _ _ _ * * * * * * _ _ _ _ _ _ _ _ * * * *1 1 1 1 * * * * * * * * _ _ _ _ _ _ _ 1 1 1 1 1 * * * * * * * * _ _ _ _ _ _ _ 1 1 1 1 * * * * * * _ _ _ _ 1 1 1 1 * * * *1 2 3 4 * * * * * * * * * 0 1 2 0 1 2 0 1 2 3 4 * * * * * * * * * 0 1 2 0 1 2 0 1 2 3 * * * * * * * 0 1 2 0 1 2 3 * * * * CONTROL CONTENTS Power ONStandby mode (or 40-second startup time) COMMAND PARAMETERRETURN RS-232C Specifications and Command Settings (Continued)