Sharp Xg C55x Projector User Manual

							LCD PROJECTOR
MODEL
XG-C55X
OPERATION MANUAL
Introduction
Connections and Setup
Basic Operation
Easy to Use Functions
Appendix 
						

							IMPORTANT
For your assistance in reporting the loss or theft of your
Projector, please record the Serial Number located on
the bottom of the projector and retain this information.
Before recycling the packaging, please be sure that
you have checked the contents of the carton thoroughly
against the list of “Supplied accessories” on page 14 .Model No.: XG-C55X
Serial No.:
This equipment complies with the requirements of Directives 89/336/EEC a\
nd 73/23/EEC as amended by 93/68/
EEC.
Dieses Gerät entspricht den Anforderungen der EG-Richtlinien 89/336/EWG und 73/23/EWG mit Änderun\
g 93/
68/EWG.
Ce matériel répond aux exigences contenues dans les directives 89/\
336/CEE et 73/23/CEE modifiées par la
directive 93/68/CEE.
Dit apparaat voldoet aan de eisen van de richtlijnen 89/336/EEG en 73/23\
/EEG, gewijzigd door 93/68/EEG.
Dette udstyr overholder kravene i direktiv nr. 89/336/EEC og 73/23/EEC med tillæg nr. 93/68/EEC.
Quest’ apparecchio è conforme ai requisiti delle direttive 89/336/\
EEC e 73/23/EEC, come emendata dalla
direttiva 93/68/EEC.
Este equipamento obedece às exigências das directivas 89/336/CEE e\
 73/23/CEE, na sua versão corrigida
pela directiva 93/68/CEE.
Este aparato satisface las exigencias de las Directivas 89/336/CEE y 73/\
23/CEE, modificadas por medio de la
93/68/CEE.
Denna utrustning uppfyller kraven enligt riktlinjerna 89/336/EEC och 73/\
23/EEC så som kompletteras av 93/68/
EEC.
Dette produktet oppfyller betingelsene i direktivene 89/336/EEC og 73/23\
/EEC i endringen 93/68/EEC.
Tämä laite täyttää direktiivien 89/336/EEC ja 73/23/EEC v\
aatimukset, joita on muutettu direktiivillä 93/68/EEC. 
						

							SPECIAL NOTE FOR USERS IN THE U.K.
The mains lead of this product is fitted with a non-rewireable (moulded) plug incorporating a 10A fuse. Should
the fuse need to be replaced, a BSI or ASTA approved BS 1362 fuse marked 
 or  and of the same rating as
above, which is also indicated on the pin face of the plug, must be used\
.
Always refit the fuse cover after replacing the fuse. Never use the plug without the fuse cover fitted.
In the unlikely event of the socket outlet in your home not being compat\
ible with the plug supplied, cut off the
mains plug and fit an appropriate type.
DANGER:
The fuse from the cut-off plug should be removed and the cut-off plug destroyed immediately and disposed of
in a safe manner.
Under no circumstances should the cut-off plug be inserted elsewhere into a 10A socket outlet, as a serious
electric shock may occur.
To fit an appropriate plug to the mains lead, follow the instructions below:
IMPORTANT:
The wires in the mains lead are coloured in accordance with the following code: Blue: Neutral
Brown: Live
As the colours of the wires in the mains lead of this product may not correspond with the coloured markings
identifying the terminals in your plug, proceed as follows:
• The wire which is coloured blue must be connected to the plug terminal which is marked N or coloured black.
• The wire which is coloured brown must be connected to the plug terminal which is marked L or coloured red.
Ensure that neither the brown nor the blue wire is connected to the earth terminal in your three-pin plug.
Before replacing the plug cover make sure that:
• If the new fitted plug contains a fuse, its value is the same as that removed from the cut-off plug.
• The cord grip is clamped over the sheath of the mains lead, and not simply over\
 the lead wires.
IF YOU HAVE ANY DOUBT, CONSULT A QUALIFIED ELECTRICIAN. 
						

							The supplied CD-ROM contains operation instructions in English, German, French, Swedish, Spanish, Italian,
Dutch, Portuguese, Chinese (Traditional Chinese and Simplified Chinese) and Korean. Carefully read through
the operation instructions before operating the projector.
Die mitgelieferte CD-ROM enthält Bedienungsanleitungen in Englisch, Deutsch, Franz ösisch, Schwedisch, Spanisch,
Italienisch, Niederl ändisch, Portugiesisch, Chinesisch (Traditionelles Chinesisch und einfaches Chinesisch) und
Koreanisch. Bitte lesen Sie die Bedienungsanleitung vor der Verwendung des Projektors sorgf ältig durch.
Le CD-ROM fourni contient les instructions de fonctionnement en anglais, allemand, fra\
n çais, su édois,
espagnol, italien, n éerlandais, portugais, chinois (chinois traditionnel et chinois simplifi é) et cor éen. Veuillez lire
attentivement ces instructions avant de faire fonctionner le projecteur.
Den medf öljande CD-ROM-skivan inneh åller bruksanvisningar p å engelska, tyska, franska, svenska, spanska,
italienska, holl ändska, portugisiska, kinesiska (traditionell kinesiska och f örenklad kinesiska) och koreanska. L äs
noga igenom bruksanvisningen innan projektorn tas i bruk.
El CD-ROM suministrado contiene instrucciones de operaci ón en ingl és, alem án, franc és, sueco, espa ñol,
italiano, holand és, portugu és, chino (chino tradicional y chino simplificado) y coreano. Lea cuidadosamente las
instrucciones de operaci ón antes de utilizar el proyector.
Il CD-ROM in dotazione contiene istruzioni per l ’uso in inglese, tedesco, francese, svedese, spagnolo, italiano,
olandese, portoghese, cinese (cinese tradizionale e cinese semplificato) e coreano. Leggere attentamente le
istruzioni per l ’uso prima di usare il proiettore.
De meegeleverde CD-ROM bevat handleidingen in het Engels, Duits, Frans, Zweeds, Spaan\
s, Italiaans,
Nederlands, Portugees, Chinees (Traditioneel Chinees en Vereenvoudigd Chinees) en Koreaans. Lees de
handleiding zorgvuldig door voor u de projector in gebruik neemt.
O CD-ROM fornecido cont ém instru ções de opera ção em Ingl ês, Alem ão, Franc ês, Sueco, Espanhol, Italiano,
Holand ês, Portugu ês, Chin ês, (Chin ês Tradicional e Chin ês Simplificado) e Coreano. Leia cuidadosamente
todas as instru ções de opera ção antes de operar o projetor. 
						

							Introduction
-1
Before using the projector, please read this operation manual carefully.
There are two important reasons for prompt warranty registration of your new SHARP Projector, using
the REGISTRATION CARD packed with the projector.1. WARRANTY This is to assure that you immediately receive the full benefit of the parts, service and labor
warranty applicable to your purchase.
2. CONSUMER PRODUCT SAFETY ACT To ensure that you will promptly receive any safety notification of inspection, modification, or
recall that SHARP may be required to give under the 1972 Consumer Product Safety Act, PLEASE
READ CAREFULLY THE IMPORTANT “LIMITED WARRANTY” CLAUSE.
WARNING:High brightness light source. Do not stare into the beam of light, or view directly. Be especially
careful that children do not stare directly into the beam of light.
WARNING:To reduce the risk of fire or electric shock, do not expose this product to rain or moisture.
WARNING:FCC Regulations state that any unauthorized changes or modifications to \
this equipment not
expressly approved by the manufacturer could void the user’s authority to operate this equip-
ment.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER.
NO USER-SERVICEABLE PARTS EXCEPT LAMP UNIT. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol,
within an equilateral triangle, is intended to
alert the user to the presence of uninsulated
“dangerous voltage” within the product’s
enclosure that may be of sufficient magnitude
to constitute a risk or electric shock to
persons.
The exclamation point within a triangle is
intended to alert the user to the presence of
important operating and maintenance
(servicing) instructions in the literature
accompanying the product.
IntroductionENGLISH
CAUTION
RISK OF ELECTRIC SHOCK.DO NOT REMOVE SCREWS EXCEPT SPECIFIED USER SERVICE SCREWS.
INFORMATION
This equipment has been tested and found to comply with the limits for a\
 Class A digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in accordance with the operation
manual, may cause harmful interference to radio communications. Operation of this equipment in a residential
area is likely to cause harmful interference, in which case the user will be required to correct the interference
at his own expense. See bottom of actual set.
The enclosed computer cable must be used with the device. The cable is p\
rovided to ensure that the device
complies with FCC Class A verification.
WARNING:
This is a Class A product. In a domestic environment this product may cause radio interference in which case the
user may be required to take adequate measures.
U.S.A. ONLY
U.S.A. ONLY
U.S.A. ONLY
U.S.A. ONLY 
						

							-2
WARNING:
The cooling fan in this projector continues to run for about 90 seconds after the projector enters the standby mode.
During normal operation, when putting the projector into the standby mode always use the STANDBY button on the
projector or on the remote control. Ensure the cooling fan has stopped before disconnecting the power cord.
DURING NORMAL OPERATION, NEVER TURN THE PROJECTOR OFF BY DISCONNECTING THE POWER CORD.
FAILURE TO OBSERVE THIS WILL RESULT IN PREMATURE LAMP FAILURE.
Caution Concerning the Lamp Replacement
See “Replacing the Lamp ” on page  85 .
PRODUCT DISPOSAL
This projector utilizes tin-lead solder, and a pressurized lamp containing a small amount of mercury. Disposal of
these materials may be regulated due to environmental considerations. For disposal or recycling information,
please contact your local authorities or, if you are located in the United States of America, the Electronic Industries
Alliance: www.eiae.org .
PRECAUTIONS A OBSERVER LORS DU
REMPLACEMENT DE LA LAMPE.
DEBRANCHER LE CORDON D’ALIMENTATION AVANT DE RETIRER LES VIS.
L’INTERIEUR DU BOITIER ETANT EXTREMEMENT CHAUD, ATTENDRE 1 HEURE
AVANT DE PROCEDER AU REMPLACEMENT DE LA LAMPE.
NE REMPLACER QUE PAR UNE LAMPE SHARP DE TYPE BQC-XGC55X//1.
RAYONS ULTRAVIOLETS : PEUVENT ENDOMMAGER LES YEUX.
ETEINDRE LA LAMPE AVANT DE PROCEDER A L’ENTRETIEN.
LAMPE A HAUTE PRESSION : RISQUE D’EXPLOSION. DANGER POTENTIEL
DE PARTICULES DE VERRE EN CAS D’ECLATEMENT DE LA LAMPE.
A MANIPULER AVEC PRECAUTION, SE REPORTER AU MODE D’EMPLOI. BEFORE REMOVING THE SCREW, DISCONNECT POWER CORD.
HOT SURFACE INSIDE. ALLOW 1 HOUR TO COOL BEFORE REPLACING THE LAMP.
REPLACE WITH SAME SHARP LAMP UNIT TYPE BQC-XGC55X//1 ONLY.
UV RADIATION : CAN CAUSE EYE DAMAGE. TURN OFF LAMP BEFORE SERVICING.
HIGH PRESSURE LAMP : RISK OF EXPLOSION. POTENTIAL HAZARD OF GLASS
PARTICLES IF LAMP HAS RUPTURED. HANDLE WITH CARE. SEE OPERATION MANUAL.
LAMP REPLACEMENT CAUTION
When Attaching the “QUICK GUIDE” Label
“QUICK GUIDE” Label
Attaching the “QUICK GUIDE ” Label (supplied) on the
projector will help you check the setup procedure. When
you attach the  “QUICK GUIDE ” Label on the projector,
be sure to align the label bottom and the upper part of
the  “Notevision ” logo on the top cabinet of the projector
as shown in the drawing on the right.
This SHARP projector uses an LCD (Liquid Crystal Display) panel. This very sophisticated panel contains 786,432
pixels ( × RGB) TFTs (Thin Film Transistors). As with any high technology electronic equipment such as large screen
TVs, video systems and video cameras, there are certain acceptable toler\
ances that the equipment must conform to.
This unit has some inactive pixels within acceptable tolerances which ma\
y result in inactive dots on the picture screen.
This will not affect the picture quality or the life expectancy of the unit. 
						

							Introduction
-3
Outstanding Features
1. Ultra High Brightness from a Compact Projector
•300W SHP Lamp
Use 300W SHP lamp for excellent color uniformity and ultra high brightne\
ss.
•Power Save mode function enables lower noise levels, reduced power
consumption and longer lamp life.
2. Simple & Easy Operation
•Color coded terminals, automatic signal search and graphical menu sys-
tem insure easy set-up and configuration.
• Frequently used connections and controls are strategically placed for
easy access.
• Simple lens replacement
Using an easy access lens cover and a new bayonet mount configuration, t\
he optional lens can be
easily installed.
3. Superior PC Compatibility
•Compatible with up to 200 Hz vertical refresh rate, Sync on Green and
Composite Sync signals for use with a wide variety of high-end PCs and
Workstations.
•
Using  Advanced Intelligent Compression  Technology, computer screens
of UXGA (1,600  # 1,200) resolution can be displayed with minimal distortion.
4. Advanced Computer & Video lntegrated Composer Technology
• Realizes vivid images using the latest image quality circuitry.
•New I/P conversion algorithm enhances the performance of the motion detect I/P
conversion.
Extensive improvements on the jagged edges or slanted
lines in moving images.
•Color Management System
Supports sRGB.
Enables individual settings of lightness, chromatic value
and hue for six target colors.
•Noise Reduction
Allows for a clear image even with noisy source signals.
•New Edge Up-Scaling
Reduces jaggies and flickering when up-scaling edges
of slanted lines, enabling sharper quality images.
5. Theft Deterrent and Security
• Anti-theft
This feature will render the projector useless if a keycode is not enter\
ed.
•
Notevision Lock Down
A secure installation is achieved by tethering one of the projector ’s
mounting points to the optical block. This added measure makes it ex-
tremely difficult to pull the projector off of its ceiling mount thus mi\
ni-
mizing the chance of injury from horseplay or unauthorized removal of
the projector. 
						

							-4
Contents
Adjusting the Picture ........................................ 46
Adjusting Image Preferences .................................. 46
Selecting the Signal Type ....................................... 46
Progressive Mode .................................................... 47
Adjusting Computer Images ............................ 48
Computer Image Adjustment .................................. 48
Saving Adjustment Settings ..................................... 48
Selecting Adjustment Settings ................................ 49
Special Mode Settings ............................................ 49
Checking the Input Signal ....................................... 49
Auto Sync Adjustment ............................................. 50
Auto Sync Display Function ................................... 50
Easy to Use Functions
Selecting the Picture Display Mode ................ 52
Displaying a Still Image .................................... 54
Enlarging a Specific Portion of an Image ....... 55
Gamma Correction Function ............................ 56
Displaying Dual Pictures (Pict in Pict) ............ 57
Black Screen Function ..................................... 58
Displaying the Break Timer .............................. 59
Color Management System (C. M. S.) .............. 60
Selecting the Color Reproduction Mode ................. 60
Selecting the Target Color ....................................... 60
Setting the Brightness of the Target Color ............... 61
Setting the Chromatic Value of the Target Color ...... 61
Setting the Hue of the Target Color ........................ 61
Resetting User-Defined Color Settings ................... 62
Overview of All Color Settings ................................. 62
Setting the Audio Output Type ......................... 63
Setting on/off the Internal Speaker .................. 63
Auto Search Function ....................................... 64
Video Digital Noise Reduction(DNR) System .............................................. 65
Setting On-screen Display ............................... 65
Setting the Video System ................................. 66
Saving Projected Images .................................. 67
Capturing the Image .............................................. 67
Deleting the Captured Image .................................. 67
Setting a Background Image ............................ 68
Selecting a Startup Image ................................ 68
Selecting the Economy Mode .......................... 69
Setting the Power Save Mode ................................. 69
Monitor Out/RS-232C Off Function .......................... 69
Auto Power Off Function ......................................... 70
Displaying the Remaining Lamp Life (Percentage) ................................................. 70
Reversing/Inverting Projected Images ............ 71
Locking the Operation Buttons on the Projector ........................................... 71
Setting up the Keylock ............................................ 71
Canceling the Keylock Setting ................................ 72
Introduction
Outstanding Features ......................................... 3
Contents ............................................................... 4
IMPORTANT SAFEGUARDS ............................... 6
How to Access the PDF Operation Manuals(Windows, Macintosh) ................................... 9
Part Names ........................................................ 10
Projector (Front and Top View) ................................ 10
Projector (Rear View) .............................................. 11
Remote Control (Front View) ................................... 12
Remote Control (Top View) ..................................... 12
Using the Remote Control ................................ 13
Available Range of the Remote Control ................. 13
Inserting the Batteries ............................................. 13
Accessories ....................................................... 14
Connections and Setup
Connecting the Projector to Other Devices .... 16
Before Connecting .................................................. 16
This projector can be connected to: ....................... 16
Connecting the Power Cord ................................... 17
Connecting the Projector to a Computer ............. 17
Connecting to Video Equipment .......................... 19
Connecting to an Amplifier .................................. 21
Controlling the Projector by a Computer ............. 22
Connecting to a Monitor ...................................... 23
Using as a Wired Remote Control ....................... 23
Using the Wireless Presentation Function of the Remote Control ............................................. 24
Setup .................................................................. 25
Using the Adjustment Feet ..................................... 25
Adjusting the Lens .................................................. 26
Setting up the Screen .............................................. 27
Screen Size and Projection Distance ...................... 28
Projecting a Reversed/Inverted Image ................... 32
Basic Operation
Setting with the Buttons
Image Projection ............................................... 34
Basic Procedure ...................................................... 34
Selecting the On-screen Display Language ........... 36
Turning the Power off .............................................. 37
Correcting Trapezoidal Distortion (Keystone Correction) ................................. 38
Setting with the Menus
Menu Bar Items ................................................. 40
Using the Menu Screen .................................... 42
Menu Selections (Adjustments) .............................. 42
Menu Selections (Settings) ..................................... 44 
						

							Introduction
-5
Selecting the Transmission Speed
(RS-232C) ..................................................... 72
Setting up a Password ...................................... 73
Entering the Password ............................................. 73
Changing the Password ......................................... 74
If You Forget Your Password ................................... 74
Setting the Anti-Theft ........................................ 75
Entering the Keycode .............................................. 75
Changing the Keycode ........................................... 76
Initializing the Settings ..................................... 77
Displaying the Adjustment Settings ................ 78
Appendix
Maintenance ...................................................... 80
Replacing the Air Filter ..................................... 81
Maintenance Indicators .................................... 83
Regarding the Lamp ......................................... 85
Lamp ...................................................................... 85
Caution Concerning the Lamp ................................ 85
Replacing the Lamp ................................................ 85
Removing and Installing the Lamp Unit ................. 86
Resetting the Lamp Timer ....................................... 87
Connecting Pin Assignments .......................... 88
(RS-232C) Specifications and
Command Settings ...................................... 89
Wired Remote Control Terminal Specifications .............................................. 92
Computer Compatibility Chart ......................... 93
Troubleshooting ................................................ 94
For SHARP Assistance ..................................... 96
Specifications .................................................... 97
Dimensions ........................................................ 98
Glossary ............................................................. 99
Index ................................................................. 100 
						

							-61. Read Instructions
All the safety and operating instructions should be read
before the product is operated.
2. Retain InstructionsThe safety and operating instructions should be
retained for future reference.
3. Heed WarningsAll warnings on the product and in the operating
instructions should be adhered to.
4. Follow InstructionsAll operating and use instructions should be followed.
5. CleaningUnplug this product from the wall outlet before cleaning.
Do not use liquid cleaners or aerosol cleaners. Use a
damp cloth for cleaning.
6. AttachmentsDo not use attachments not recommended by the
product manufacturer as they may cause hazards.
7. Water and MoistureDo not use this product near water–for example, near
a bath tub, wash bowl, kitchen sink, or laundry tub; in a
wet basement; or near a swimming pool; and the like.
8. AccessoriesDo not place this product on an unstable cart, stand,
tripod, bracket, or table. The product may fall, causing
serious injury to a child or adult, and serious damage
to the product. Use only with a cart, stand, tripod,
bracket, or table recommended by the manufacturer,
or sold with the product. Any mounting of the product
should follow the manufacturer’s instructions, and
should use a mounting accessory recommended by
the manufacturer.
9. TransportationA product and cart combination
should be moved with care. Quick
stops, excessive force, and
uneven surfaces may cause the
product and cart combination to
overturn.
10.VentilationSlots and openings in the cabinet are provided for
ventilation to ensure reliable operation of the product
and to protect it from overheating, and these openings
must not be blocked or covered. The openings should
never be blocked by placing the product on a bed,
sofa, rug, or other similar surface. This product should
not be placed in a built-in installation such as a book-
case or rack unless proper ventilation is provided or
the manufacturer’s instructions have been adhered to.
IMPORTANT SAFEGUARDS
11. Power SourcesThis product should be operated only from the type of
power source indicated on the marking label. If you
are not sure of the type of power supply to your home,
consult your product dealer or local power company.
For products intended to operate from battery power,
or other sources, refer to the operating instructions.
12. Grounding or PolarizationThis product is provided with one of the following types
of plugs. If the plug should fail to fit into the power outlet,
please contact your electrician.
Do not defeat the safety purpose of the plug.
a. Two-wire type (mains) plug.
b. Three-wire grounding type (mains) plug with a grounding terminal.
This plug will only fit into a grounding type power
outlet.
13. Power-Cord ProtectionPower-supply cords should be routed so that they are
not likely to be walked on or pinched by items placed
upon or against them, paying particular attention to
cords at plugs, convenience receptacles, and the point
where they exit from the product.
14. LightningFor added protection for this product during a lightning
storm, or when it is left unattended and unused for long
periods of time, unplug it from the wall outlet and
disconnect the cable system. This will prevent damage
to the product due to lightning and power-line surges.
15. OverloadingDo not overload wall outlets, extension cords, or integral
convenience receptacles as this can result in a risk of
fire or electric shock.
16. Object and Liquid EntryNever push objects of any kind into this product through
openings as they may touch dangerous voltage points
or short-out parts that could result in a fire or electric
shock. Never spill liquid of any kind on the product.
17. ServicingDo not attempt to service this product yourself as
opening or removing covers may expose you to dan-
gerous voltage or other hazards. Refer all servicing to
qualified service personnel.
CAUTION: Please read all of these instructions before you operate this product \
and save these
instructions for later use.
Electrical energy can perform many useful functions. This product has been engineered and manufactured to
assure your personal safety. BUT IMPROPER USE CAN RESULT IN POTENTIAL ELECTRICAL SHOCK OR
FIRE HAZARDS. In order not to defeat the safeguards incorporated in this product, observe the following basic
rules for its installation, use and servicing.