Sharp Xg C330x Projector Quickstart Guide

							-21
Setting up the Projector Network Environment
1
2
After confirming or setting, proceed to “3. Setting up Network Connection for the Pro-
jector”.
5Click “Internet Protocol (TCP/IP)”,
and click the “Properties” button.
6Confirm or change an IP address
for the setup computer.
1Confirm and note the current IP ad-
dress, Subnet mask and Default
gateway.
Make sure to note the current IP ad-
dress, Subnet mask and Default gate-
way as you will be required to reset
them later.
2Set  temporarily as follows :
IP address : 192.168.150.3
Subnet mask : 255.255.255.0
Default gateway : (Do not input any
values.)
Note
•When “DHCP Client” is set to “OFF” on the
projector:
IP address : 192.168.150.2
Subnet mask : 255.255.255.0
Default gateway : 0.0.0.0
7After setting, click the “OK” but-
ton, and then restart the com-
puter. 
						

							-22
Setting up the Projector Network Environment
3. Setting up a NetworkConnection for the
Projector
Settings for such items as the projector’s IP
address and subnet mask are compatible with
the existing network.
Set each item on the projector as follows. (See
page 53 of the projector’s operation manual
for setting.)
DHCP Client : Off
IP Address : 192.168.150.002
Subnet Mask : 255.255.255.000
1Start Internet Explorer (version
5.0 or later) on the computer, and
enter “http://192.168.150.2/”  in
“Address”, and then press the
“Enter” key.
2If a user name and a password
have not yet been set, just click
the “OK”  button.
• If a user name and a password have
been set, input the user name and the
password, and click the “OK” button.
• If the user name or password is entered
incorrectly three times, an error mes-
sage will be displayed.
3When the screen as shown on
the right appears, click “TCP/IP”. 
						

							-23
4The TCP/IP setting screen ap-
pears, ready for network settings
for the projector.
Note
•Confirm the existing network’s segment (IP
address group) to avoid setting an IP ad-
dress that duplicates the IP addresses of
other network equipment or computers. If
“192.168.150.2” is not used in the network
having an IP address of “192.168.150.XXX”,
you don’t have to change the projector IP
address.
•For details about each setting, consult your
network administrator.
5Click the “Apply” button.
6The set values appear. Confirm
that the values are set properly,
and then click the “Confirm” but-
ton.
Setting up the Projector Network Environment
•Close the browser.
•This completes the network settings.
•After setting items, wait for 10 seconds and then re-access.
•Change the IP address of the setting computer back to its original address, which you have noted down in
Step 6-1 on page 21, and then connect the computer and the projector to the network.
Setting example / RemarksSelect “ON” or “OFF” to determinewhether to use DHCP Client.
You can set this item when “DHCP
Client” is set to “OFF”.
Factory default setting: 192.168.150.2
Enter an IP address appropriate
for the network.
You can set this item when “DHCP
Client” is set to “OFF”.
Factory default setting: 255.255.255.0
Set the subnet mask to the same
as that of the computer and
equipment on the network.
You can set this item when “DHCP
Client” is set to “OFF”.
Factory default setting: 0.0.0.0
* When not in use, set to “0.0.0.0”.
Factory default setting: 0.0.0.0
* When not in use, set to “0.0.0.0”.
ItemsDHCPClient
IP Address
Subnet
Mask
Default
Gateway
DNS
Server 
						

							-24
Controlling the Projector via LAN
Controlling the Projector
Using Internet Explorer
(Version 5.0 or later)
Complete connections to external equipment
before starting the operation. (See pages 21-
29 of the projector’s operation manual.)
Complete the AC cord connection. (See page
30 of the projector’s operation manual.)
Note
•When connecting the projector to the LAN, use
a LAN cable (Category 5).  When connecting the
projector to a hub, use a straight-through cable.
1Start Internet Explorer (version 5.0
or later) on the computer.
2Enter “http://” followed by the
projector IP address set by the
procedure on page 23  followed
by  “/” in “Address”, and then
press the “Enter” key.
•When “DHCP Client” is set to “OFF” on
the projector, IP address is
192.168.150.2. If you did not change the
IP address in  “3. Setting up a Network
Connection for the Projector”  (pages
22 -23
), enter “http://192.168.150.2/”.
3A screen for controlling the pro-
jector appears, ready for per-
forming various  status condi-
tions,  control, and settings.
After connecting the projector to your network, enter the projector IP address in “Address”
on Internet Explorer (version 5.0 or later) using a computer on the network to start a setup
screen that will enable control of the projector via the network. 
						

							-25
Confirming the Projector
Status (Status)
On this screen, you can confirm the projector
status. You can confirm the following items :
• •• •
•MAC Address
• •• •
•Power
• •• •
•Condition
• •• •
•Lamp Timer
• •• •
•Lamp Life
• •• •
•Input
• •• •
•Signal Info
• •• •
•Serial Number
Note
•If you click the “Refresh” button before the
screen is displayed completely, an error
message (“Server Busy Error”) will be dis-
played. Wait for a moment and then oper-
ate again.
•For details about each item, refer to the
projector’s operation manual.
Controlling the Projector via LAN
Controlling the Projector
(Control)
On this screen, you can perform projector con-
trol. You can control the following items :
• •• •
•Power
• •• •
•Input Select
• •• •
•Volume
• •• •
•AV  Mute
Note
•If you click the “Refresh” button before the
screen is displayed completely, an error mes-
sage (“Server Busy Error”) will be displayed.
Wait for a moment and then operate again.
•You cannot operate this page while the pro-
jector is warming up.
•While the projector is in standby mode, you
can only control “Power ON”.
•For details about each item, refer to the
projector’s operation manual. 
						

							-26
Controlling the Projector via LAN
Setting and Adjusting the
Projector (Settings & Adjustments)
Example: “Picture” screen display for INPUT 1
On these screens, you can make projector
settings or adjustments. You can set or adjust
the following items :
•
• •
•
•Picture Mode
•
• •
•
•CLR Temp•
• •
•
•Progressive (Video)•
• •
•
•Signal Type  (Computer,  DVI)•
• •
•
•Dynamic Range (DVI)•
• •
•
•Video System (Video)•
• •
•
•Resolution Setting•
• •
•
•A uto Sync•
• •
•
•Resize•
• •
•
•A uto Keystone•
• •
•
•OSD Display•
• •
•
•Background•
• •
•
•Eco/Quiet Mode•
• •
•
•A uto Power Off•
• •
•
•System Sound•
• •
•
•Menu Position•
• •
•
•Direct Power On•
• •
•
•P assword•
• •
•
•Internal Speaker•
• •
•
•A udio Out•
• •
•
•Projection Mode•
• •
•
•F an Mode•
• •
•
•Monitor Out•
• •
•
•RS-232C Speed•
• •
•
•All Reset•
• •
•
•Language
Note
• If you click the “Refresh” button before the
screen is displayed completely, an error mes-
sage (“Server Busy Error”) will be displayed.
W ait for a moment and then operate again.
• You cannot operate this page while the pro-
jector is warming up.
• For details about each item, refer to the
projector’s operation manual.
Setting the Security
(Network – Security)
On this screen, you can make settings relat-
ing to security.
Note
• User Name and Password can be up to 8
characters.
• You can input the characters below :
a-z, A-Z, 0-9, -, _
Description
Setting of user name for
security protection.
Setting of password for
security protection.
It is possible to set up to three
IP addresses allowing connec-
tion to the projector.
No limits are set to IP addresses
connecting to the projector.
Fo r security improvement, only an
IP address set by “Address 1-3”
can be connected to the projector.
Items
User Name
P assword
Accept IP
Address
All IPAddresses
From only
specific IP
addresses 
						

							-27
Controlling the Projector via LAN
Making General Settings
for the Network 
(Network -
General)
On this screen, you can make general settings
relating to the network.
After clicking the “Apply” button, the set val-
ues appear. Confirm that the values are set
properly, and then click the “Confirm” button.
Note
•After setting items, wait for 10 seconds and
then re-access.
•Projector Name can be up to 12 characters.
•You can input the characters below :
A-Z, 0-9, -, _, (,), space
(When “a-z” are input, they are converted to
“A-Z” automatically.)
Description
Setting the projector name.
Setting the time interval in
which the projector will be
automatically disconnected
from the network in units of a
minute (from 1 to 65535
minutes). If the set value is
made 0, the Auto Logout
function is disabled.
Setting the TCP port number
used when exchanging data
with the projector (from 1025 to
65535).
Setting the port number used
when searching for the
projector (from 1025 to 65535).
ItemsProjector
Name
Auto
Logout
Time
Data Port
Search
Po r t
Setting example / Remarks
Setting an SMTP server
address for e-mail transmis-
sion.
e.g.1 : 192.168.150.253
e.g.2 : smtp123.sharp.co.jp
*When using a domain name,
make settings for the DNS
server.
Setting the projector’s e-mail
address. The e-mail address set
here becomes Originator E-mail
Address.
Setting the sender’s name.
The name set here appears in
the “Originator Name” column
of the body of the message.
Items
SMTP
Server
Originator
E-mail
Address
Originator
Name
Setting for Sending E-mail
when an Error Occurs
(Mail – Originator Settings)
On this screen, you can make settings for
sending e-mail to report when the projector
has generated an error.
Note
•SMTP Server, Originator E-mail Address and
Originator Name can be up to 64 characters.
•
You can input the characters below:
SMTP Server and Originator E-mail Address :
a-z, A-Z, 0-9, !, #, $, %, &, *, +, -, /, =, ?, ^, {,
|, }, ~
, _, ’, ., @, `
(You can input “@” only one time for “Origi-
nator E-mail Address”.)
Originator Name : a-z, A-Z, 0-9, -, _, (,), space
•
If the settings of “3. Setting up a Network
Connection for the Projector” on pages 22
and 23 are incorrectly set, e-mail will not be
send. 
						

							-28
Controlling the Projector via LAN
Setting Error Items and
Destination Addresses to
which E-mail is to be Sent
when an Error Occurs
(Mail – Recipient Settings)
On this screen, you can input e-mail destina-
tions to which error notification (error items)
e-mails are sent.
Note
•E-mail Address can be up to 64 characters.
•You can input the characters below :
a-z, A-Z, 0-9, !, #, $, %, &, *, +, -, /, =, ?, ^, {, |,
}, ~
, _, ’, ., @, `
(You can input “@” only one time.)
•For details about error items, refer to the
projector’s operation manual.
Description
Set addresses to which error
notification e-mail is sent. You
can set up to five addresses.
Error e-mail is sent on the error
items checked in their check
boxes.
Send test e-mail. This allows
you to confirm that the settings
for e-mail transmission are
properly set.
Items
E-mail
Address
Error Mail
(Lamp, Temp,Fan, Cover)
Test
Setting Error Items and
the URL that are to be
Displayed when an Error
Occurs 
(Service & Support –
Access URL)
On this screen, you can make settings of the
URL and error items that are to be displayed
when the projector has generated an error.
Example of the display when an error occurs
Description
Set the URL that is to be
displayed when an error
occurs. You can set up to five
addresses.
The URL is displayed when an
error checked in their check
boxes occurs.
The set URL site is test-
displayed. This allows you to
confirm that the URL site is
properly displayed.
Items
Access
URL
Condition(Always, Lamp,
Temp, Fan, Cover)
Test 
						

							-29
Setting up the Projector Using RS-232C or Telnet
When Connecting Using
RS-232C
1Launch general purpose terminal
emulator.
2Input settings for the RS-232C port
of the terminal emulator as follows.
Baud Rate : 9600 bps*
Data Length : 8 bit
Parity Bit : None
Stop Bit : 1 bit
Flow Control : None
*This is the factory default setting. If the value
of Baud Rate for the projector has been
changed, set Baud Rate here according to
the changed value on the projector.
3Input “PJS11234” and press the “En-
ter” key.
4“OK” is displayed. Input “PJS25678”
and press the “Enter” key within 10
seconds.
5“User Name:” is displayed. Input the
user name and press the “Enter”
key.
•If a user name has not yet been set, just
press the “Enter” key.
6“Password:” is displayed. Input the
password and press the “Enter” key.
•If a password has not yet been set, just press
the “Enter” key.
Connect the projector to a computer using RS-232C or Telnet, and open the SETUP MENU on
the computer to carry out various settings for the projector.
7Input “setup” and press the “Enter”
key.
•SETUP MENU will be displayed.
Note
•User name and password are not set in the fac-
tory default settings.
•If the user name or password is entered incor-
rectly three times, SETUP MENU will be quit. ▼SETUP MENU
---------------------------------SETUP MENU--------------------------------
[1]IP Address [2]Subnet Mask [3]Default Gateway
[4]User Name [5]Password
[6]RS-232C Baud Rate [7]Projector Name [8]DHCP Client
[A]Advanced Setup [D]Disconnect All
[V]View All Setting [S]Save & Quit [Q]Quit Unchanged
setup> 
						

							-30
Setting up the Projector Using RS-232C or Telnet
When Connecting Using
Telnet
1Click “Start” from the Windows® desk-
top and select “Run”.
2Enter “telnet 192.168.150.2” in the text
box that opens up. (If the IP address
of the projector is 192.168.150.2.)
3Click the “OK” button.
4“User Name:” is displayed. Input the
user name and press the “Enter”
key.
•If a user name has not yet been set, just
press the “Enter” key.
5“Password:” is displayed. Input the
password and press the “Enter” key.
•If a password has not yet been set, just press
the “Enter” key.
6Input “setup” and press the “Enter”
key.
•SETUP MENU will be displayed.
Note
•If the IP address has been changed, be sure to
enter the new IP address in step 2.
•User name and password are not set in the fac-
tory default settings.
•If the user name or password is entered incor-
rectly three times in steps 4 or 5, SETUP MENU
will be quit.
---------------------------------SETUP MENU--------------------------------
[1]IP Address [2]Subnet Mask [3]Default Gateway
[4]User Name [5]Password
[6]RS-232C Baud Rate [7]Projector Name [8]DHCP Client
[A]Advanced Setup [D]Disconnect All
[V]View All Setting [S]Save & Quit [Q]Quit Unchanged
setup>
▼SETUP MENU