Sharp R1500 Service Manual

							29
R-1500R-1501R-1505R-1506
1.Disconnect the power supply cord.
2.Open the door and block it open.
3.To discharge the high voltage capacitor, wait for 60
seconds.
4.Remove the one (1) screw holding the base cover to the
oven cavity back plate.
5.Remove the three (3) screws holding the base cover to
the oven cavity front face plate.
6.Open the base cover.
7.   Release the two hood lamp sockets from the base cover.
8.Remove the base cover from the oven cavity by pulling
down and moving to the left slightly.
10.Pull the wire leads from the oven lamp socket by pushing
the terminal hole of the oven lamp socket with the small
flat type screw driver.
11. Now, the oven lamp socket is free.
TURNTABLE MOTOR AND FOOD LAMP SOCKETS REMOVAL
TURNTABLE MOTOR
9.Disconnect the wire leads from the  turntable motor.
10.Remove one (1) screw holding turntable motor to the
oven cavity.
11.Now the turntable motor is free.
HOOD LAMP SOCKET
9.Screw the hood lamp off from the lamp socket.
10.Disconnect the wire leads from the lamp socket by
pushing the terminal hole of the lamp socket with the
small flat type screw driver.
11. Now, the lamp socket is free.
1.Disconnect the power supply cord.
2.Open the door and block it open.
3.Remove three (3) screws holding the hood exhaust
louver to oven cavity front face plate.
4.    Remove the hood exhaust louver from the oven by
pushing the right and left tabs of the hood exhaust louver.
(Refer to procedure of HOOD EXHAUST LOUVER
REMOVAL)
7.Turn the lamp socket and release it from the magnetron
duct.
8.Screw the oven lamp off from the lamp socket.
9.  Now, the oven lamp is free.
OVEN LAMP AND LAMP SOCKET REMOVAL
POSITIVE LOCK®  CONNECTOR (NO-CASE TYPE) REMOVAL
1.Disconnect the power supply cord and remove the oven
from wall and remove outer case. (Refer to procedure of
Removal of Oven from Wall and Outer case Removal)
2.Open the door and block it open.
3.To discharge the high voltage capacitor, wait for 60
seconds.
4.Push the lever of positive lock® connector.
5.Pull down on the positive lock® connector.
CAUTION:WHEN CONNECTING THE POSITIVE LOCK®
CONNECTORS TO THE TERMINALS, IN-
STALL THE POSITIVE LOCK® SO THAT THE
LEVER FACES YOU.
Positive lock® connector
5.Remove one (1) screw holding the control panel to the
oven cavity front face plate.
6.Release the control panel from the oven cavity front face
plate by lifting it up and tilting top edge back.
Oven lamp
socket
Terminal
Wire lead
Terminal hole
Flat type small
screw driver
1. Disconnect the power supply cord.
2. Open the door and block it open.
3. To discharge the high voltage capacitor, wait for 60seconds.
4. Remove three (3) screws holding the hood exhaust louver to oven cavity front face plate.
5. Remove the hood exhaust louver from the oven by pushing the right and left tabs of the hood exhaust louver.
(Refer to procedure of "HOOD EXHAUST LOUVER
REMOVAL")
CONTROL PANEL ASSEMBLY, CONTROL UNIT  AND KEY UNIT REMOVAL
6. Remove one (1) screw holding the control panel to theoven cavity front  face plate.
7. Release the control panel from the oven cavity front face plate by lifting it up.
8. Disconnect the wire leads from the relays RY1 and RY2.
9. Disconnect the connectors CN-A, CN-B and CN-E from the control unit.
10. Remove the control panel assembly from the oven.
11.Now, the control panel assembly is free.
12.Disconnect the connector CN-G from the control unit.
Terminal
Push
Pull down 1
2
Lever
Positive lock®
connector 
						

							30
R-1500
R-1501
R-1505
R-1506
13.Remove the two (2) screws holding the LCD holder to
the key fixing plate.
14.Remove two (2) screws holding the power unit to the key
fixing plate.
15.Release the two (2) tabs holding the power unit to the key
fixing plate.
16.Release the three (3) tabs holding the LCD to the LCD
holder.
17.Release the two (2) tabs holding the LSI unit to the LCD
holder.
18.Remove the LCD holder and the LED sheet.
19.Now, the control unit is free.
20.Remove the one (1) screw holding the key fixing plate to
the control panel.
21.Release the six (6) tabs holding the key fixing plate to the
control panel.
22.Remove the key fixing plate from the control panel.
23.Remove the key unit from the key fixing plate.
24.Now, the key unit is free
NOTES FOR KEY UNIT REPLACEMENT
1. Do not reuse the torn key unit because the performance
of the adhesive becomes weak.2. Before attaching a new key unit, wipe off remaining
adhesive on the key fixing plate surfaces completely with
a soft cloth soaked in alcohol.
3. When attaching the key unit to the key fixing plate, adjust
the upper edge and right edge of the key unit to the
correct position of  key fixing plate. See key unit location.
4. Stick the key unit firmly to the key fixing plate by rubbing
with soft cloth not to scratch.
Key unit location
1. Disconnect the power supply cord and remove the oven
from wall and remove outer case. (Refer to procedure of
"Removal of Oven from Wall" and "Outer case Removal")
2. Open the door and block it open.
3. To discharge the high voltage capacitor, wait for 60
seconds.
4. Remove the three (3) screws holding the hood intake duct
R to the oven cavity top plate, the oven cavity front flange
and the fan duct. And remove the hood intake duct R.
5. Remove the control panel assembly, referring to the
procedure of "CONTROL PANEL ASSEMBLY ,
CONTROL UNIT AND KEY UNIT REMOVAL".
6. Remove the two (2) screws holding the latch hook to the
oven cavity front flange.
7. Remove the latch hook from the oven cavity front flange.
8. Disconnect the wire leads of each switch.
DOOR SENSING SWITCH, PRIMARY INTERLOCK SWITCH AND MONITOR SWITCH REMOVAL
9. Remove each switch from the latch hook by pushing the
one (1) stopper tab holding each switch.
10.Now, each switch is  free.
Re-install
1. Re-install each switch in its place. The primary interlock
switch is in the lower position, door sensing switch is in
the upper position and the monitor switch is in the middle
position.
2. Re-connect wire leads to each switch. Refer to pictorial
diagram.
3. Secure the latch hook (with two (2) mounting screws) to
oven cavity front flange.
4. Make sure that the monitor switch is operating properly
and check continuity of the monitor circuit.    Refer to
chapter "Test Procedure" and "Adjustment procedure".
1. Disconnect the power supply cord and remove the oven
from wall and remove outer case. (Refer to procedure of
"Removal of Oven from Wall" and "Outer case Removal")
2. Open the door and block it open.
3. To discharge the high voltage capacitor, wait for 60
seconds.
4. Remove the three (3) screws holding the hood intake duct
R to the oven cavity top plate, the oven cavity front flange
and the fan duct. And remove the hood intake duct R.
5. Remove the control panel assembly, referring to the
procedure of "CONTROL PANEL ASSEMBLY ,
CONTROL UNIT AND KEY UNIT REMOVAL".
If the door sensing switch, primary interlock switch and
monitor switch do not operate properly due to a
misadjustment, the following adjustment should be made.
DOOR SENSING SWITCH, PRIMARY INTERLOCK SWITCH AND MONITOR SWITCH ADJUSTMENT
6. Loosen the two (2) screws holding latch hook to the oven
cavity front flange.
7. With door closed, adjust latch hook by moving it back and
forth, and up and down. In and out play of the door
allowed by the upper and lower position of the latch hook
should be less than 0.5mm. The vertical position of the
latch hook should be adjusted so that the door sensing
switch and primary interlock switch are activated with the
door closed. The horizontal position of the latch hook
should be adjusted so that the monitor switch is activated
with the door closed.
8. Secure the screws with washers firmly.
9. Check all of the switches operation. If any switch has not
activated with the door closed, loosen screw and adjust
the latch hook position.
Key unit
Key 
fixing plate 
						

							31
R-1500
R-1501
R-1505
R-1506
After adjustment, check the following.
1. In and out play of door remains less than 0.5mm when in
the latched position. First check upper position of latch
hook, pushing and pulling upper portion of door toward
the oven face. Then check lower portion of the latch
hook, pushing and pulling lower portion of the door
toward the oven face. Both results (play in the door)
should be less than 0.5mm.
2. The door sensing switch and primary interlock switch
interrupt the circuit before the door can be opened.
3. Monitor switch contacts close when door is opened.
4. Re-install outer case and check for microwave leakage
around door with an approved microwave survey meter.
(Refer to Microwave Measurement Procedure.)
Figure C-1. Latch Switch Adjustments
DOOR ASSEMBLY REMOVAL
1. Disconnect the power supply cord.
2. Open the door and block it open.
3. To discharge the high voltage capacitor, wait for 60
seconds.
4. Remove the three (3) screws holding the hood exhaust
louver to the oven cavity front face plate.
5. Remove the hood exhaust louver from the oven cavity by
pushing the right and left tabs of the hood exhaust louver.
(Refer to the procedure of "HOOD EXHAUST LOUVER
REMOVAL".)
6. Insert a putty knife (thickness of about 0.5mm) into the
gap  A  between the door stopper and the choke cover
as shown in Figure C-3 to free engaging parts.
7. Lift up the door stopper.
8. Now, the door stopper is free from the door assembly.
9. Lift up the door assembly to release the upper and lower
door hinge pins from the upper and lower oven hinges.
10.Now, the door assembly is free.
Note: When the individual parts are replaced, refer to
Door Disassembly.
DOOR ASSEMBLY RE-INSTALL
1. On re-installing door, insert the lower oven hinge to lower
door hinge pin.
2. Insert the upper oven hinge to the upper door hinge pin.
3. Shut the door (close the contacts of interlock switches).
4. Make sure upper and lower oven hinges are inserted into
the upper an lower door hinge pins.
5. Make sure the door is parallel with oven face lines (left
and upper side lines) and door latch heads pass through
latch holes correctly.
6. Re-install the door stopper to the door assembly.
7. Re-install the hood exhaust louver to the oven cavity
front face plate with the three (3) screws.
Note: After any service to the door;
(A) Make sure that door sensing switch and primary
interlock switch are operating properly. (Refer to
chapter Test Procedures.)
(B) An approved microwave survey meter should be
used to assure compliance with proper microwave
radiation emission limitation standards.
DOOR REPLACEMENT
After any servicing, make sure of the following :
1. Door latch heads smoothly catch latch hook through
latch holes and that latch head goes through center of
latch hole.
2. Deviation of door alignment from horizontal line of cavity
face plate is to be less than 1.0mm.
3. Door is positioned with its face pressed toward cavity
face plate.
4. Re-install outer case and check for microwave leakage
around door with an approved microwave survey meter.
(Refer to Microwave Measurement Procedure.)
Note: The door on a microwave oven is designed to
act as an electronic seal preventing the leakage
of microwave energy from oven cavity during
cook cycle. This function does not require that
door be air-tight, moisture (condensation)-tight
or light-tight. Therefore, occasional appearance
of moisture, light or sensing of gentle warm air
movement around oven door is not abnormal
and do not of themselves indicate a leakage of
microwave energy from oven cavity.
Figure C-2. Door Replacement and adjustment
Latch hook
Door sensing
switch
Latch heads
Monitor switch
Primary interlock switch Open lever Door
Hood exhaust louver Left tab
Right tab
RE-INSTALL
RE-INSTALLLower door
hinge pinLower 
oven
hinge Upper door
hinge pin
Upper 
oven
hinge
Door stopper Door assembly
Latch 
headsScrew
Screw
Screw 
						

							32
R-1500
R-1501
R-1505
R-1506
1. Disconnect the power supply cord.
2. Open the door and block it open.
3. To discharge the high voltage capacitor, wait for 60
seconds.
4. Remove the three (3) screws holding the hood exhaust
louver to the oven cavity front face plate.
5. Remove the hood exhaust louver from the oven cavity by
pushing the right and left tabs of the hood exhaust louver.
(Refer to the procedure of "HOOD EXHAUST LOUVER
REMOVAL".)
6. Remove door assembly, referring to "DOOR
REPLACEMENT".
Replacement of door components are as follows:
7. Place door assembly on a soft cloth with latches facing
up.
Note: As the engaging part of choke cover and door frame
are provided at 15 places, do not force any particular
part.
CHOKE COVER
8. Insert a putty knife (thickness of about 0.5mm) into the
gap A between the choke cover and door stopper and
between the choke cover and the door frame as shown
Figure C-3 to free engaging parts.
9. Pry the choke cover by inserting a putty knife in order
shown in Figure C-3.
10.Now choke cover is free from door panel and door frame.
NOTE: When carrying out any repair to the door, do not
bend or warp the slit choke (tabs on the  door
panel assembly) to prevent microwave leakage.
DOOR DISASSEMBLY
DOOR FRAME ASSEMBLY
11.Remove two (2) screws holding the door panel to the
door frame assembly.
12.Release the door panel from the door frame assembly.
NOTE: It is easier to release the engaging parts of the upper
or lower door hinge pin side at first.
13.Now, door frame assembly is free.
LATCH SPRING, LATCH HEAD AND DOOR PANEL
14.Release the latch spring from the tab of the latch head
and tab of the door frame.
15.Release the latch head from the door frame.
16.Now, the latch spring and latch head are free.
Figure C-3. Door Disassembly
Choke coverDoor stopper
Putty knife
Door frame A 
						

							33
R-1500
R-1501
R-1505
R-1506
6
45
12
3
6
45
12
3 A
B
C
D
E
F
G
HA
B
C
D
E
F
G
H
Figure S-1. Pictorial Diagram
HIGH VOLTAGE
RECTIFIER HIGH VOLTAGE
CAPACITOR HIGH VOLTAGE
WIRE A
HIGH VOLTAGE COMPONENTS CONTROL UNIT
POWER 
TRANSFORMERPower Supply
cord 120V 60Hz
1 2 3
WHT
GRNBLK
WHT
BLU
GRNBLK
CAVITY
THERMAL
CUT-OUTMAGNETRON
TEMPERATURE 
FUSE
BLK
RED
BLK
FAN
MOTOR
WHT
PNK
or
BLU
WHT
ORG
PPL
BRN
WHT
Blue 
Marking 
Blue Marking OVEN LAMP & 
SOCKET
HOOD LAMP & 
SOCKET HOOD LAMP & 
SOCKET
CN-E
GRYWHTWHT
WHTWHT
RED
PRIMARY
INTERLOCK
SWITCHN.O. N.C.
COM.COM. MONITOR
SWITCHFUSE &
HOLDER
N.O.
N.O.
GRNRED
GRNGRN
GRN
N.O.
COM.
DOOR SENSING SWITCH
CN-BCN-C CN-G
CN-C
CN-A CN-E
1
911
2 1 14
5 SECONDARY INTERLOCK RELAY 
RY1
RY3
RY2:
RY4
C100
T1HOOD FAN MOTOR
12 3 4 5 6
WHTRED
YLW
BLUBLK WHTRED
YLW
BLUBLK
12
RED GRN1
2
3
4
5YLWRED
PPLCN-A
TURNTABLE
MOTOR
WHTBRN
HOOD FAN
THERMAL 
CUT-OUT
GRYBRN
RED
RED
ORG
BLK
GRYGRY
to Base Plate Right 
1
2
3
4
5
6
7
BLKPNK orORG
WHT8
9BRNCN-B
RY5
RY6
COM.
COM.
RY2:
WHTBLKORGREDR
E
D
RED
RED
REDWHT
BLK
MAGNETRON
REDWHTWHT
BLU
WHT 
						

							34
R-1500
R-1501
R-1505
R-1506
6
45
12
3
6
45
12
3 A
B
C
D
E
F
G
HA
B
C
D
E
F
G
H
Figure S-2. Power Unit Circuit
N.O
C 1
C 7
C 3
C 5
C12
C 4
C 9
C 2
C 8
C 6
C13
C14
E 2E 1
C11
C10
N.O
COM
COM
B 7
B 9
B 5
B 3
B 1
A 5
A 3
A 1
+
–
+
–
T1
VRS1
(J1)
R30 3.3k10G471K
D21
1SS270A D22
1SS270A D23
1SS270A D24
1SS270A D25
1SS270A
D40
1SS270A D20
1SS270A
D26
1SS270A
C1 0.1µ/50v
C2 1000µ/35v
38
D3 D1
D2
R1 750 1w 
SP1
PKM22EPT  Q21
KRC243MC21
10µ/35v D1-D4
1N4002
C100
7µ/230v
R2 750 1w 
AC(N)
OVEN LAMP
TURNTABLE
MOTOR
FAN MOTOROVEN LAMP
TURNTABLE
MOTOR
FAN MOTOR
CN-C
14pin
WIRE HARNESSBUZZER
MICRO. GND
VC
VA
INT
HOOD
THERMAL
CUT-OUT AC(H)
MICRO.
HIGH
LOW
CN-B
CN-A
CN-E HOOD MOTOR
HOOD MOTOR
COM.HOOD MOTOR
H/L
HOOD MOTOR
COM.
HOOD LAMP
HOOD LAMP
Q22
DOOR
SENSING
SWITCH
DOOR
SENSING
SWITCHVR
HOOD LAMP
HOOD LAMP
MOTOR RUN
CAPACITOR
NOTE
D4
1
a
b
cd
5
RY1
RY2
RY3
RY4
RY5
RY6
: IF NOT SPECIFIED,  1/4W ± 5% 
						

							35
R-1500
R-1501
R-1505
R-1506
Figure S-3. LSI Unit Circuit
6
45
12
3
6
45
12
3 A
B
C
D
E
F
G
HA
B
C
D
E
F
G
H
C 5C 1C 7C 2C 9C 8C 3C 6C 4C12C11C14
G11G12G 9
G 8
KEY UNITPOPCORN RICEREHEAT
CENTER
POULTRY
BONELESS
FROZEN
VEGETABLESFRESH
VEGETABLES
POWER
LEVELBAKED
POTATOESPOULTRY
BONE-INTIMER
CLOCK FROZEN
ENTREESHOT
WATERLIGHT
HI / LO
FAN
HI / LO
STEAKS /
CHOPS
12
453
86
9
0 7GROUND
MEAT
(DEFROST CENTER)
GROUND
MEAT
(COOK CENTER)
KEEP
WARM
G 7
G 6
G 5
G 4
G 3
G 2
G 1
G10
+
–
C10C13
C10 47µ/16v
C11 0.1µ/50v
C20 0.1µ/50v
C60 330p/50vC61 330p/50vC62 330p/50vC63 330p/50v
C40 0.01µ/25v
C14
0.01µ
/25v
C12
0.1µ/50v
C13
0.01µ/25v
R5 4.7k
R12
15k
R10
1k
R11
15k
R13
4.7k R14
4.7k R15 4.7k(J11)
4.7k
4.7k
4.7k
12kF
4.7k(J10)
(J13) (J12)
(J15) (J14)
(J17) (J16) ZD10
UDZ4.3BR4 82
LD1 LD2 LD3 LD4
INT
GND
VC
VR
H. MOTOR
H / L
H. MOTOR
COM.
HOOD
LAMP
HOOD
LAMP
BUZZER
OVEN LAMP
TURNTABLE
MOTOR
FAN MOTOR
MICRO.
Q22
DOOR
SENSING
SWITCH 
NOTE : : IF NOT SPECIFIED, 1/16W ± 5% VA
Q2
KTA1661
Q23 DTA143EAK
Q24 DTA143EAK
Q25 DTA143EAK
Q26 DTA143EAK
Q30 DTA143EAK
R41 15kCF1
CSTS4.00MG03 GND
SEG8
SEG9
SEG10
SEG11
SEG12
SEG13
SEG8 VL2
VL2 P41
P40
RESET
P71
P70
XIN
XOUT
VSS
P27
P26
P25
P24
P23
P22
P21
P20COM0
COM0
COM1
COM2
NC
SEG0
SEG1
SEG2
SEG3
SEG4
SEG5
SEG6
SEG7
SEG8
SEG9
SEG10
SEG11
SEG12
SEG13
SEG14
SEG15
SEG16
SEG17
SEG18
SEG19
SEG20
SEG21 COM1
COM2
COM3COM0(LCD)
COM1(LCD)
COM2(LCD)
COM0(LCD)
COM1(LCD)
COM2(LCD) AVSS
VREF
VCC
SEG0
SEG1
SEG2
SEG3
SEG4
SEG5
SEG6
SEG7
VL1
AN7
AN6
AN5
AN4
AN3
AN2
AN1
AN0
P57
P56
P55
CNTR0
P53
P52
P51
P50
P47
P46
P45
P44
P43
INT0
SEG14
SEG9
SEG15
SEG10
SEG11
SEG12
SEG13
SEG14
SEG15
SEG16
SEG16
SEG17
SEG18
SEG19
SEG20
SEG21
SEG17
SEG18
SEG19
SEG20
SEG21
SEG22
SEG23
SEG24
P11
P12
P13
P14
P15
P16
P17
F
24 41 164
25 40 80 6526 1
G
IC1
HI
R40 4.7k
R67
15k
R66
15k
R65
15k
R64
15k
R63
15k
R62
15k
R61
15k
R60
15kR100
4.7k
R80
1M R71 15k
R70 15k
R69 15k
R68 15k
Q21 DTA143EAK
Q22 DTA143EAKH
I
G
FQ10
2SA1037AK Q11
DTA143EKA
R6 4.7k
R72 270k
R73 270kR74 270kR75 270k
STOP
CLEARSTART
MINUTE
PLUS
CPU UNIT
LIQUID CRYSTAL DISPLAY
COOK DEFROST SENSOR AUTO %NO.
LBS.
CUPS.
KGOZ. 
						

							36
R-1500
R-1501
R-1505
R-1506
6
45
12
3
6
45
12
3 A
B
C
D
E
F
G
HA
B
C
D
E
F
G
H
Figure S-4. Printed Wiring Board
0
F
CS
M
27A 94V 0MB
MR
35
0R
BFB
DIP
LOT  NO.
QKITPB035MRE0
RY1VRS1 R30
T1S8 5
13PC100
D26
D24
D23
D22 C21CN-ECN-C
D21D40
D20
2
1 R2
Q21Q1
BB
ZD1
EER1
R3
C2
D1
D3
D4
D2
D25
1
1 95 RY5
CN-BCN-AC1 C31
1214
SP1
J1RY2RY3RY4RY6 
						

							37
R-1500
R-1501
R-1505
R-1506
PARTS LIST
Note: The parts marked “∆” may cause undue microwave exposure.
The parts marked “*” are used in voltage more than 250V. 
§ MARK: PARTS DELIVERY SECTION
ELECTRIC PARTS
1- 1 FH-DZB016MRY0 M High voltage rectifier assembly  1 AH
1- 2 RC-QZA234WRE0 M High voltage capacitor  1 AP
1- 3 QFS-TA013WRE0 M Temperature fuse 150˚C (Magnetron)  1 AE
1- 4 RMOTDA211WRE0 M Turntable motor  1 AL
1- 5 RTHM-A070WRE0 M Thermal cut-out 145˚C (Cavity)  1 AF
1- 6 RTHM-0044MRE0 M Thermal cut-out N.O. 60˚C (Hood Fan)  1 AH
1- 7 RTRN-B068MRE0 M Power transformer  1 BC
1- 8 RV-MZA288WRE0 M Magnetron 1 BK
1- 9 QFSHDB003MRE0 M Fuse holder  1 AD
1-10 QSW-MA085WRE0 M Primary interlock and door sensing switches  2 AE
1-11 FFS-BA016/KIT M Monitor switch (V-16G-2C25) with fuse (20A) assembly  1 AF
1-12 FACCDB011MRE0 M Power supply cord  1 AQ
1-13 QSOCLB006MRE0 M Oven lamp socket  3 AE
1-14 FMOTEA441WRKZ M Hood fan motor  1 BC
1-15 RMOTEA406WRZZ M Fan motor  1 AT1-16 RLMPTA068WRE0 M Oven lamp  3 AE
CABINET PARTS
2- 1 LSTY-B024MRP0 M Rear stay  1 AE
2- 2 PDIF-B030MRF0 M Hood exhaust louver  [R-1500]  1 AQ
2- 2 PDIF-B031MRF0 M Hood exhaust louver  [R-1501]  1 AQ
2- 2 PDIF-B030MRF0 M Hood exhaust louver  [R-1505]  1 AQ
2- 2 PDIF-B031MRF0 M Hood exhaust louver  [R-1506]  1 AQ
2- 3 GDAI-B065MRP0A M Base plate R  1 AG
2- 4 HDECQB027MRF0 M Front panel L [R-1500]  1 AL
2- 4 HDECQB028MRF0 M Front panel L [R-1501]  1 AL
2- 4 HDECQB027MRF0 M Front panel L [R-1505]  1 AL
2- 4 HDECQB028MRF0 M Front panel L [R-1506]  1 AL
2- 5 GCABUB103MRP0 M Outer case cabinet [R-1500]  1 AZ
2- 5 GCABUB105MRP0 M Outer case cabinet [R-1501]  1 AZ
2- 5 GCABUB103MRP0 M Outer case cabinet [R-1505]  1 AZ
2- 5 GCABUB105MRP0 M Outer case cabinet [R-1506]  1 AZ
2- 6 TMAPCB067MRR0 M Schematic diagram  1 AB
2- 7 FANGKB009MRY0 M Hood lamp glass assembly [R-1500]  1 AN
2- 7 FANGKB010MRY0 M Hood lamp glass assembly [R-1501]  1 AM
2- 7 FANGKB009MRY0 M Hood lamp glass assembly [R-1505]  1 AN
2- 7 FANGKB010MRY0 M Hood lamp glass assembly [R-1506]  1 AM
2-7-1 LANGQB016MRP0 M Hood lamp glass angle [R-1500]  1 AG
2-7-1 LANGQB020MRP0 M Hood lamp glass angle [R-1501]  1 AG
2-7-1 LANGQB016MRP0 M Hood lamp glass angle [R-1505]  1 AG
2-7-1 LANGQB020MRP0 M Hood lamp glass angle [R-1506]  1 AG
2-7-2 PGLSPB004MRE0 M Hood lamp glass  1 AH
2- 8 PCOVPB096MRT0 M Base cover [R-1500]  1 AV
2- 8 PCOVPB097MRT0 M Base cover [R-1501]  1 AV
2- 8 PCOVPB096MRT0 M Base cover [R-1505]  1 AV
2- 8 PCOVPB097MRT0 M Base cover [R-1506]  1 AV
CONTROL PANEL PARTS
3- 1 CPWBFB060MRU0 M Control unit 1 BF
3- 1A QCNCMA017JDZZ M 3-pin connector CN-A 1 AA
3- 1B QCNCMA448DRE0 M 5-pin connector CN-B 1 AA
3- 1C QCNCMA275DRE0 J 2-pin connector CN-E 1 AB
3- 1D FW-VZB189MRE0 M Lead wire harness CN-C 1 AB
C1 RC-KZA087DRE0 J Capacitor     0.1 uF    50V 1 AB
C2 VCEAB31VW108M J Capacitor    1000 uF    35V 1 AF
C21 VCEAB31VW106M J Capacitor      10 uF    35V 1 AB
C100 RC-QZB014MRE0 M Capacitor       7 uF   230V 1 AK
D1-4 RH-DZA006PRE0 J Diode (1N4002) 4 AD
D20-26 VHD1SS270A/-1 J Diode (1SS270A) 7 AA
D40 VHD1SS270A/-1 J Diode (1SS270A) 1 AA
Q21 VSKRC243M//-3 J Transistor (KRC243M) 1 AB
R1-2 VRS-B13AA751J J Resistor       750 ohm   1W 2 AB
R30 VRD-B12EF332J J Resistor      3.3k ohm   1/4W 1 AA
RY1-2 RRLY-A113DRE0 M Relay (DU24D1-1PR(M)) 2 AG
RY3 RRLY-A123DRZZ M Relay (G5S-1 24V) 1 AG
RY4-6 RRLY-B004MRE0 M Relay (FTR-F3AA024E) 3 AG
REF. NO. PART NO.§DESCRIPTION QTY CODE
*
*
*
∆* 
						

							38
R-1500
R-1501
R-1505
R-1506
REF. NO. PART NO.§DESCRIPTION QTY CODE
∆
∆
∆∆
∆
∆
∆
∆
∆
∆
∆
∆
∆
SP1 RALM-A014DRE0 J Buzzer (PKM22EPT) 1 AG
T1 RTRNPB017MRE0 M Transformer 1 BG
VRS1 RH-VZA032DRE0 J Varistor (10G471K) 1 AE
3- 2 FPNLCB372MRK0 M Control panel sub. assembly [R-1500] 1 AZ
3- 2 FPNLCB373MRK0 M Control panel sub, assembly [R-1501] 1 AZ
3- 2 FPNLCB372MRK0 M Control panel sub. assembly [R-1505] 1 AZ
3- 2 FPNLCB373MRK0 M Control panel sub, assembly [R-1506] 1 AZ
3- 2-1 FUNTKB320MRE0 M Key unit [R-1500] 1 AQ
3- 2-1 FUNTKB321MRE0 M Key unit [R-1501] 1 AQ
3- 2-1 FUNTKB320MRE0 M Key unit [R-1505] 1 AQ
3- 2-1 FUNTKB321MRE0 M Key unit [R-1506] 1 AQ
3- 2-2 JBTN-B106MRF0 M Open button [R-1500] 1 AE
3- 2-2 JBTN-B108MRF0 M Open button [R-1501] 1 AE
3- 2-2 JBTN-B106MRF0 M Open button [R-1505] 1 AE
3- 2-2 JBTN-B108MRF0 M Open button [R-1506] 1 AE
3- 2-3 JBTN-B107MRF0 M Select button [R-1500] 1 AC
3- 2-3 JBTN-B109MRF0 M Select button [R-1501] 1 AC
3- 2-3 JBTN-B107MRF0 M Select button [R-1505] 1 AC
3- 2-3 JBTN-B109MRF0 M Select button [R-1506] 1 AC
3- 2-4 MSPRTA050WRE0 M Button spring 1 AA
3- 3 LHLD-B009MRF0 M LCD holder 1 AF
3- 4 PSHEPB023MRE0 M LED sheet 1 AR
3- 5 XEPSD30P10XS0 M Screw; 3mm x 10mm 5 AB
OVEN PARTS
4- 1 LSTPPB038MRF0 M Door stopper  1 AB
4- 2 FROLPB025MRK0 M Turntable support  assembly  1 AN
4- 3 NTNT-A095WRE0 M Turntable tray  1 AN
4- 4 LBNDKB009MRP0 M Capacitor holder  1 AB
4- 5 PDUC-B111MRF0 M Magnetron duct  1 AF
4- 6 MLEVPB016MRF0 M Open lever  1 AD
4- 7 ************* M Oven cavity (Not replaceable part)  1 --
4- 8 PPACGB014MRF0 M Turntable motor packing  1 AA
4- 9 PHOK-B018MRF0 M Latch hook  1 AF
4-10 FANGTB005MRY0 M Unit mounting plate assembly  1 AS
4-11 NFANPB006MRE0 M Fan blade  1 AC
4-12 LBSHC0037WRE0 M Cord bushing  1 AB
4-13 MLEVFB007MRP0 M Mounting lever  2 AC
4-14 PDUC-B112MRP0 M Hood intake duct R  1 AG
4-15 PCOVPB085MRP0 M Waveguide cover  1 AH
4-16 MSPRTA046WRE0 M Latch spring  2 AB
4-17 LANGTB055MRP0 M Chassis support 2 AD
4-18 PDUC-B115MRF0 M Hood duct R  1 AQ
4-19 PDUC-B114MRF0 M Hood duct L  1 AQ
4-20 PDUC-B113MRP0 M Fan duct  1 AH
4-21 PDUC-B117MRF0 M Orifice  1 AC
4-22 PCUSGB043MRP0 M Transformer cushion  1 AC
DOOR PARTS
5 CDORFB279MRK0 M Door assembly [R-1500]  1 BD
5 CDORFB280MRK0 M Door assembly [R-1501]  1 BD
5 CDORFB283MRK0 M Door assembly [R-1505]  1 BD
5 CDORFB284MRK0 M Door assembly [R-1506]  1 BD
5- 1 FDORFB070MRT0 M Door panel assembly  1 AW
5- 2 FCOV-B186MRK0 M Door frame assembly [R-1500] 1 AY
5- 2 FCOV-B187MRK0 M Door frame assembly [R-1501] 1 AY
5- 2 FCOV-B191MRK0 M Door frame assembly [R-1505] 1 AY
5- 2 FCOV-B192MRK0 M Door frame assembly [R-1506] 1 AY
5-2-1 LSTPPB021MRF0 M Latch head 1 AD
5-2-2 MSPRTA046WRE0 M Latch spring 1 AB
5-2-3 LSTPPB037MRF0 M Glass stopper 2 AC
5- 3 GCOVHB044MRF0 M Choke cover 1 AG
5- 4 PSHEPB021MRE0 M Sealer film  1 AE
5- 5 XCPSD40P08000 M Screw : 4mm x 8mm  2 AA
MISCELLANEOUS
6- 1 CFZK-B460MRK0 M Installation material assembly  1 AH
6-1-1 LBSHC0040MRE0 M Grommet  1 AC
6-1-2 LX-BZ0195WRE0 M Toggle screw  4 AC
6-1-3 LX-MZB001MRE0 M Cord holder  1 AB
6-1-4 XBRSD50P60000 M Screw : 5mm x 60mm 2 AA
6-1-5 XOTSD40P12000 M Screw : 4mm x 12mm 3 AA
6-1-6 XTSSD50P35000 M Screw : 5mm x 35mm 6 AA