Sharp Projector Pg F320w User Manual

DATA PROJECTOR
MODEL
PG-F320W
Introduction Quick Start
SetupConnections Basic
Operation Useful
Features
Appendix
OPERATION MANUAL 

ii
IMPORTANT
•For your assistance in reporting the loss
or theft of your Projector, please record
the Model and Serial Number located on
the bottom of the projector and retain this
information.
• Before recycling the packaging, please
ensure that you have checked the con-
tents of the carton thoroughly against the
list of “Supplied accessories” on page  11.Model No.:
Serial No.: 

iii
SPECIAL NOTE FOR USERS IN THE U.K.
The mains lead of this product is fitted with a non-rewireable (moulded) plug incorporat-
ing a 10A fuse. Should the fuse need to be replaced, a BSI or ASTA approved BS 1362
fuse marked 
 or  and of the same rating as above, which is also indicated on the pin
face of the plug, must be used.
Always refit the fuse cover after replacing the fuse. Never use the plug without the fuse
cover fitted.
In the unlikely event of the socket outlet in your home not being compat\...

iv
The supplied CD-ROM contains operation instructions in English, German, French,
Spanish, Italian, Dutch, Swedish, Portuguese, Chinese and Korean. Carefully read
through the operation instructions before operating the projector.
Die mitgelieferte CD-ROM enthält Bedienungsanleitungen in Englisch, Deutsch, Franzö\
sisch,
Spanisch, Italienisch, Niederländisch, Schwedisch, Portugiesisch, Chinesisch und Koreanisch.
Bitte lesen Sie die Bedienungsanleitung vor der Verwendung des Projektors sorgfältig durch....

1
IntroductionBefore using the projector, please read this operation manual carefully.
There are two important reasons for prompt warranty registration of your new SHARP
Projector, using the REGISTRATION CARD packed with the projector.
1. WARRANTY
This is to assure that you immediately receive the full benefit of the parts, service
and labor warranty applicable to your purchase.
2. CONSUMER PRODUCT SAFETY ACT
To ensure that you will promptly receive any safety notification of inspection,
modification, or...

2
Caution Concerning Lamp Replacement
See “Replacing the Lamp” on page 57 .
This SHARP projector uses a DLP® chip. This very sophisticated panel contains 1,024,000 pixels
(micromirrors). As with any high technology electronic equipment such as large screen TVs,
video systems and video cameras, there are certain acceptable tolerances that the equipment
must conform to.
This unit has some inactive pixels within acceptable tolerances which ma\
y result in inactive dots
on the picture screen. This will not...

3
Introduction
39
Useful
Features
Using the Menu Screen
Menu Selections (Adjustments)
Example: Adjusting “Bright”.• This operation can also be performed by using the buttons on the projector.Press  MENU/HELP .•The “Picture” menu screen for the se-
lected input mode is displayed.Example: “Picture” screen menu for COMPUTER (RGB) input
Press Q or  O and select “Picture”
to adjust.
1
2
Menu item
Picture Mode
Contrast 0 0
0BrightStandard
SEL./ADJ. ENTER END
Picture
SCR PRJ Net. Help
0
0
Red
BlueCLR Temp...

4
Contents
Preparing
Introduction
How to Read this Operation Manual.... 3
Contents ............................................... 4
IMPORTANT SAFEGU ARDS............... 6
How to Access the PDF Operation Manuals ............................................ 10
Accessories ........................................ 11
Pa rt Names and  Functions................. 12
Projector............................................... 12
Rear View ............................................. 13
Inserting the Batteries...

5
Introduction
Setting up the Projector NetworkEnvironment (“Network”  menu)........ 49
Setting a Password .............................. 49
DHCP Client Setting ............................. 50
TCP/IP Setting ...................................... 50
Confirming the Projector Information ... 50
T roubleshooting with the
“Help” Men u...................................... 51
Utilizing the “Help” Menu Functions .... 51
Reference
Appendix
Maintenance....................................... 52
Cleaning and...

6
1. Read InstructionsAll the safety and operating instructions should
be read before the product is operated.
2. Retain InstructionsThe safety and operating instructions should be
retained for future reference.
3. Heed WarningsAll warnings on the product and in the operating
instructions should be adhered to.
4. Follow InstructionsAll operating and use instructions should be
followed.
5. CleaningUnplug this product from the wall outlet before
cleaning. Do not use liquid cleaners or aerosol
cleaners. Use...