Sharp Projector Pg F312x User Manual

27
Basic
Operation
3 Adjusting the Height
The height of the projector can be ad-
justed using the adjustment feet at the
front and rear of the projector.
When the screen is above the projec-
tor, the projection image can be made
higher by adjusting the projector.
1
2
3
• Do not apply too much pressure on the pro-
jector when the front adjustment foot comes
out.
• When lowering the projector, be careful not to
get your fingers caught in the area between
the adjustment foot and the projector.
•
Hold the...

28
0
KEYSTONEADJUST END
Correcting Trapezoidal
Distortion
When the image is projected either from
the top or from the bottom towards the
screen at an angle, the image becomes
distorted trapezoidally. The function for
correcting trapezoidal distortion is
called Keystone Correction.
•The Keystone Correction can be adjusted up
to an angle of approximately ±40 degrees and
the screen can also be set up to an angle of
approximately ±40 degrees (when the resize
mode is set to “NORMAL” (see page  30)).
Note
1
2...

29
Basic
Operation
Displaying the Black Screen
and Turning off the Sound
T emporarily
Adjusting the Volume
Switching the Input Mode
Press  COMPUTER , DVI , S-VIDEO  or
VIDEO  on the remote control to select
the input mode.
• When you press  INPUT on the projector or  DVI
on the remote control, the INPUT list appears.
Press  P/R  to switch the INPUT mode.
Select the appropriate input mode for
the connected equipment.
Press  VOL +/–  on the remote control or
– O /Q + on the projector to adjust the vol-...

30
Resize Mode
This function allows you to modify or customize the resize mode to enhance the input image. De-
pending on the input signal, you can choose a desired image.
Press RESIZE .•See page 43 for setting on menu screen.RESIZE
button
COMPUTER
STRETCH
For 4:3 screen For 16:9 screen
Input signal
Image type
NORMALFULL BORDER
4:3 aspect ratio
5:4 aspect ratio
16:10 aspect ratio 16:9 aspect ratio
: 
Cutout area on which images cannot be projected
:  Area where the signals are off screen
The Image Shift...

31
Basic
Operation
VIDEOVIDEO/DTV
*1
*1
*1
*1
*1
*1
*1
*1
*2*2
4:3 aspect ratio
Squeeze
Letter box
16:9 aspect ratio 16:9 aspect ratio
(4:3 aspect ratio in 16:9)
For 4:3 screen For 16:9 screen
Input signal
Image type
NORMAL
Video/DTV
480I,  480P,
576I,  576P,
NTSC, PAL, SECAM
720P, 1035I,
1080I,  1080P
540P
:  Cutout area on which images cannot be projected
:  Area on which the image is not included in the original signals
The Image Shift function can be used for these images.
Same as NORMAL mode.
BORDER...

32
Operating with the Remote Control
Displaying and Setting the
Break Timer
Press BREAK TIMER .•The timer starts to count down from 5
minutes.1
2
Press  P/R /O /Q  to adjust the
length of the break time.
• Increases with  P or Q
5 minutes  s 6 minutes  s 60 minutes•Shortens with  O or  R4 minutes  s 3 minutes s 1 minute
• The break time can be set in units of one
minute (up to 60 minutes).
On-screen display
Canceling the break timer display function
Press  BREAK TIMER .
•Break Timer does not function...

33
Useful
Features
Auto Sync
(Auto Sync Adjustment)
Freezing a Moving Image
• When the optimum image cannot be achieved
with Auto Sync adjustment, use the help menu
for manual adjustments. (See page  48.)
Au to Sync function works when detect-
ing input signal after the projector turns
on.
Press  AUTO SYNC  to manually adjust
with Auto Sync function.
Press  FREEZE .
•The projected image is frozen.
Press  FREEZE  again to return to
the moving image from the cur-
rently connected device.
Note
Selecting the...

34
Using the Remote Control as the Wireless Computer Mouse
When connecting the projector and the computer with a USB cable, you can use
the remote control as the computer mouse.
If the computer is placed too far away from the projector to be connected via the
USB cable, the remote receiver (optional, AN-MR2) makes it possible to operate
the projector with the remote control.  For details, see the operation manual of
the receiver.
Connecting with a USB cable
or
Remote receiver 
(optional, AN-MR2)To USB...

35
Useful
Features
The following shows the items that can be set in the projector.
Menu Items
Picture Mode
Contrast 0
0
0
0
BrightColorTint0
Sharp
Standard
SEL./ADJ. ENTER END 0
0
Red
Blue
Picture
SCR - ADJ PRJ - ADJ Help
Picture Mode
CLR Temp
BrilliantColor
TMC.M.S. Setting
C.M.S. Standard
SEL./ADJ. ENTER END
Progressive
Lamp Setting
0
1
On
3D Progressive
Bright
DNR
Off
Reset
Picture SCR - ADJ PRJ - ADJ Help
PAGE 2
Main menu Sub menuPicture
Page 40Page 40
Page 41
Page 41
Page 41
Page 41
Page 41
Page 42...

36
Menu Items (Continued)
SEL./ADJ.ENTEREND
Resize
Image Shift
0
0
Keystone
OSD Display
Background
Setup Guide
PRJ Mode
Language Front
English On Logo On Border
Picture
SCR - ADJ PRJ - ADJ Help
Closed Caption Off
Main menu Sub menuSCR - ADJ
Page 43
Language
Image Shift Resize
Page 43
Page 43
Page 43
Page 43
Page 44
Page 44
Page 44
Page 44
Keystone
OSD Display [On/Off]
Background
Setup Guide [On/Off]
PRJ Mode Logo
Blue
None
Page 44Closed Caption
Off
CC1
CC2
Front
Ceiling + Front
Rear
Ceiling + Rear...