Sharp Projector Pg F267x User Manual

27
Basic            
Operation
Image Projection
About the Setup Guide
After turning on the projector, the Setup 
Guide screen appears to assist you with 
projector setup.
Guidance items
  1 FOCUS
  2 HEIGHT ADJUST
Press  ENTER  to exit the Setup Guide 
screen.
The Setup Guide screen automatically 
highlights the items in the following order:
1 FOCUS
3 ENTER2 HEIGHT ADJUST
However, you can adjust the focus or height 
(angle) regardless of the highlighted item.
If you do not want to display the Setup...

28
Image Projection (Continued)
2 Adjusting the Height
The height of the projector can be 
adjusted using the adjustment feet at the 
front and rear of the projector.
When the screen is above the projector, 
the projection image can be made higher 
by adjusting the projector.
1  Lift the projector to adjust its 
height while lifting the HEIGHT 
ADJUST lever.
2  Remove your hands from the 
HEIGHT ADJUST lever of the 
projector after its height has 
been  nely adjusted.
 The angle of projection is...

29
Basic            
Operation
Correcting Trapezoidal 
Distortion
When the image is projected either from 
the top or from the bottom towards the 
screen at an angle, the image becomes 
distorted trapezoidally. The function for 
correcting trapezoidal distortion is called 
Keystone Correction.
The Keystone Correction can be adjusted up 
to an angle of approximately ±22 degrees and 
the screen can also be set up to an angle of 
approximately ±22 degrees (when the resize 
mode is set to “NORMAL” (see page...

30
Image Projection (Continued)
Switching the Input Mode
Select the appropriate input mode for the 
connected equipment.
Press COMPUTER, DVI, S-VIDEO or 
VIDEO on the remote control to select 
the input mode.
When you press INPUT on the projector or DVI 
on the remote control, the INPUT list appears.
Press P/R to switch the INPUT mode. 
Adjusting the Volume
Press VOL +/– on the remote control 
or –O/Q+ on the projector to adjust 
the volume.
Pressing VOL–/–O will lower the volume.
Pressing VOL+/Q+ will...

31
Basic            
Operation
Resize Mode
This function allows you to modify or customize the resize mode to enhance the input 
image. Depending on the input signal, you can choose a desired image.
Press RESIZE.
See page 44 for setting on menu screen.
COMPUTER
Main resolution NORMAL FULL DOT BY DOT BORDER STRETCH
4:3 aspect ratioSVGA (800 × 600)
1024 × 768 —800 × 600
768 × 576
1024 × 576 XGA (1024 × 768) —
SXGA (1152 × 864) 1152 × 864
UXGA (1600 × 1200) 1600 × 1200
Other aspect ratios
SXGA (1280 × 1024)...

32
Image Projection (Continued)
VIDEO/DTV
Input signal For 4:3 screen For 16:9 screen
Video/DTV Image type NORMAL AREA ZOOM V-STRETCH BORDER STRETCH
480
I, 480P,
576I, 576P,
NTSC, PAL,
SECAM
4:3 aspe ct ratio
                   *1                   *1
 
Squeeze
                   *1                   *1
Letter box
                   *1                   *1
720P, 1035I,
1080I, 1080P16:9 aspect ratio                    *1
—*2—*2
540P16:9 aspect ratio
(4:3 aspect ratio in 16:9)
                   *1
 :...

33
Useful        
Features
Operating with the Remote Control
POINTER button
ECO+QUIET button
Adjustment buttons 
(P/R/O/Q) BREAK TIMER button
SPOT button
AUTO SYNC button FREEZE button
PICTURE MODE button MAGNIFY buttons
EFFECT button
Displaying and Setting the 
Break Timer
1 Press BREAK TIMER.The timer starts to count down from 5 
minutes.
On-screen display
2 Press P/R/O/Q to adjust the 
length of the break time.
Increases with P or Q
5 minutes ➞ 6 minutes ➞ 60 minutesShortens with O or R4 minutes ➞ 3...

34
Operating with the Remote Control (Continued)
Auto Sync
(Auto Sync Adjustment)
Auto Sync function works when detecting 
input signal after the projector turns on.
Press AUTO SYNC to manually adjust 
with Auto Sync function.
When the optimum image cannot be achieved 
with Auto Sync adjustment, use the help 
menu for manual adjustments. (See page 
51.) 
Note
Freezing a Moving Image
1 Press FREEZE.The projected image is frozen.
2 Press FREEZE again to return to 
the moving image from the 
currently...

35
Useful        
Features
Using the Remote Control as the Wireless Computer Mouse
When connecting the projector and the computer with a USB cable, you can use the 
remote control as the computer mouse.
If the computer is placed too far away from the projector to be connected via the USB 
cable, the remote receiver (optional, AN-MR2) makes it possible to operate the 
projector with the remote control.  For details, see the operation manual of the 
receiver.
Connecting with a USB cable
or
Remote receiver...

36
Menu Items
The following shows the items that can be set in the projector.
“Picture” menuMain menu Sub menuPicture
Page 41Page 41
Page 42
Page 42
Page 42
Page 42
Page 42
Page 43
Page 43
+30 -30Contrast
+30 -30
+30 -30
+30 -30
1 -1
2 0
+30 -30+30 -30+30 -30Tint Color
Sharp Bright
Progressive
Lamp Setting
Reset2D Progressive
3D Progressive
Film Mode CLR Temp
BrilliantColor™
C.M.S. Setting [On/Off]
C.M.S.Standard
Presentation
Movie
Game
sRGB*1 Picture Mode
*2 *2
*2
Red
Blue
*2
Page 43
DNR Off
Level 1...