Sharp Projector PG-D3510X PG-D3010X PG-D2710X User Manual

							7
Introduction15. OverloadingDo not overload wall outlets, extension cords, 
or integral convenience receptacles as this 
can result in a risk of  re or electric shock.
16. Object and Liquid Entr yNever push objects of any kind into this 
product through openings as they may touch 
dangerous voltage points or short-out parts 
that could result in a  re or electric shock. 
Never spill liquid of any kind on the product.
17.  ServicingDo not attempt to service this product 
yourself as opening or removing covers 
may expose you to dan ger ous voltage or 
other hazards. Refer all servicing to 
quali ed service personnel.
18.  Damage Requiring ServiceUnplug this product from the wall outlet 
and refer servicing to quali ed service 
person nel under the following conditions:
a.  When the power-supply cord or plug is 
damaged.
b.  If liquid has been spilled, or objects 
have fallen into the product.
c.  If the product has been exposed to rain 
or water.
d.  If the product does not operate normally 
by following the operating instructions. 
Adjust only those con trols that are 
covered by the operating instructions, 
as an improper adjustment of other 
controls may result in damage and will 
often require extensive work by a 
quali ed technician to restore the 
product to normal operation.
e.  If the product has been dropped or 
damaged in any way.
f.  When the product exhibits a distinct 
change in performance, this indicates a 
need for service.
19. Replacement PartsWhen replacement parts are required, be 
sure the service technician has used 
replace ment parts speci ed by the 
manufacturer or have the same 
characteristics as the original part. 
Unauthorized substitutions may result in 
 re, electric shock, or other hazards.
20. Safety CheckUpon completion of any service or repairs 
to this product, ask the service technician 
to per  form safety checks to determine that 
the product is in proper operating 
condition.
21.  Wall or Ceiling MountingThis product should be mounted to a wall 
or ceiling only as recommended by the 
manufacturer.
22. HeatThis product should be situated away from 
heat sources such as radiators, heat 
registers, stoves, or other products 
(including ampli ers) that produce heat.
DLP® and the DLP logo are registered trademarks of Texas Instruments and 
BrilliantColorTM and DLP® LinkTM are trademarks of Texas Instruments.
Microsoft® and Windows® are registered trademarks of Microsoft Corporation in the 
United States and/or other countries.
PC/AT is a registered trademark of International Business Machines Corporation in the 
United States.
Adobe
® Reader® is a trademark of Adobe Systems Incorporated.
Macintosh® is a registered trademark of Apple Computer, Inc. in the United States and/or 
other countries. 
PJLink is a registered trademark or an application trademark in Japan, the United States, 
Canada, E.U., China and/or other countries/regions.
All other company or product names are trademarks or registered trademarks of their 
respective companies.
Some IC chips in this product include con dential and/or trade secret property belonging 
to Texas Instruments. Therefore you may not copy, modify, adapt, translate, distribute, 
reverse engineer, reverse assemble or discompile the contents thereof. 






 
						

							8
Observe the following safeguards when setting up your 
projector.
Caution concerning the lamp unit
Potential hazard of glass particles if lamp 
ruptures. In case of lamp rupture, contact 
your nearest Sharp Authorized Projector 
Dealer or Service Center 
for replacement.
See “Regarding the Lamp” 
on page 
60.
Caution concerning the setup of the 
projector
For minimal servicing and to maintain high 
image quality, SHARP recommends that 
this projector be installed in an area free 
from humidity, dust and cigarette smoke. 
When the projector is subjected to these 
environments, the vents and lens must be 
cleaned more often. As long as the 
projector is regularly cleaned, use in these 
environments will not reduce the overall 
operation life of the unit. Internal cleaning 
should only be performed by a Sharp 
Authorized Projector Dealer or Service 
Center. 
Rest your eyes occasionally.
Continuously watching the screen for long 
hours will cause eye strain. Take regular 
breaks to rest your eyes.
Do not set up the projector in places 
exposed to direct sunlight or bright light.
Position the screen so that it is not in direct 
sunlight or room light. Light falling directly 
on the screen washes out the colors, 
making viewing diffi cult. Close the curtains 
and dim the lights when setting up the 
screen in a sunny or bright room.
Caution regarding placing of the projector
Place the projector on a level site within the 
adjustment range (9 degrees) of the 
adjustment foot.
After the projector is purchased, a faint 
smell from the vent may appear when the 
power is fi rst turned on. This is normal and 
is not a malfunction. It will disappear after 
the projector is used for a while. ■
■
■
■
■
■
When using the projector in high-
altitude areas such as mountains (at 
altitudes of approximately 1,500 
meters (4,900 feet) or more)
When you use the projector in high-altitude 
areas with thin air, set “Fan Mode” to 
“High”. Neglecting this can affect the 
longevity of the optical system.
Use the projector at altitudes of 2,300 
meters (7,500 feet) or less.
Warning about placing the projector in 
a high position
When placing the projector in a high 
position, make certain it is carefully secure 
to avoid personal injury caused by the 
projector falling down.
Do not subject the projector to hard 
impact and/or vibration.
Protect the lens so as not to hit or damage 
the surface of the lens.
Avoid locations with extremes of 
temperature.
The operating temperature of the projector 
is from 41°F to 95°F (+5°C to +35°C).
The storage temperature of the projector is 
from  – 4°F to 140°F (–20°C to +60°C).
Do not block the exhaust and intake 
vents.
Allow at least 11 13/16 inches (30 cm) of 
space between the exhaust vent and the 
nearest wall or obstruction.
Ensure that the intake vent and the exhaust 
vent are not obstructed.
If the cooling fan becomes obstructed, a 
protection circuit will automatically put the 
projector into Standby mode to prevent 
overheat damage. This does not indicate a 
malfunction. (See pages 
58 and 59.) 
Remove the projector power cord from the 
wall outlet and wait at least 10 minutes. 
Place the projector where the intake and 
exhaust vents are not blocked, plug the 
power cord back in and turn on the 
projector. This will return the projector to 
the normal operating condition. ■
■
■
■
■
■
■
■
■ 
						

							9
IntroductionCaution regarding usage of the projector
If you are not to use the projector for a long 
time or before moving the projector, make 
certain you unplug the power cord from the 
wall outlet, and disconnect any other 
cables connected to it.
Do not carry the projector by holding the 
lens.
When storing the projector, ensure that you 
close the lens shutter.
Do not expose the projector to direct 
sunlight or place next to heat sources. 
Doing so may affect the cabinet color or 
cause deformation of the plastic cover.
Other connected equipment
When connecting a computer or other 
audio-visual equipment to the projector, 
make the connections AFTER unplugging 
the power cord of the projector from the 
AC outlet and turning off the equipment to 
be connected.
Please read the operation manuals of the 
projector and the equipment to be 
connected for instructions on how to make 
the connections. ■
■
■
■
■
■
Using the projector in other countries
The power supply voltage and the shape of 
the plug may vary depending on the region 
or country you are using the projector in. 
When using the projector overseas, make 
sure you use an appropriate power cord for 
the country you are in.
Temperature monitor function
If the temperature inside the projector 
increases, due to blockage of the air vents, 
or the setting location, the temperature 
warning indicator will blink. And if the 
temperature keeps on rising, “
” will 
illuminate in the lower left corner of the 
picture with the temperature warning 
indicator blinking. If this state continues, 
the lamp will turn off, the cooling fan will 
run and then the projector will enter 
Standby mode. Refer to “Maintenance 
Indicators” on pages 
58 and 59 for details.
Info
The cooling fan regulates the internal 
temperature, and its performance is automatically 
controlled. The sound of the fan may change 
during projector operation due to changes in the 
fan speed. This does not indicate malfunction.
■
■

Closed Caption uses Bitstream Vera fontsCopyright (c) 2003 by Bitstream, Inc. All Rights Reserved. Bitstream Vera is a trademark of Bitstream, Inc.
Permission is hereby granted, free of charge, to any person obtaining a copy of the fonts accompanying this 
license (“Fonts”) and associated documentation fi les (the “Font Software”), to reproduce and distribute the 
Font Software, including without limitation the rights to use, copy, merge, publish, distribute, and/or sell 
copies of the Font Software, and to permit persons to whom the Font Software is furnished to do so, subject 
to the following conditions:
The above copyright and trademark notices and this permission notice shall be included in all copies of one 
or more of the Font Software typefaces.
The Font Software may be modifi ed, altered, or added to, and in particular the designs of glyphs or 
characters in the Fonts may be modifi ed and additional glyphs or characters may be added to the Fonts, 
only if the fonts are renamed to names not containing either the words “Bitstream” or the word “Vera”.
This License becomes null and void to the extent applicable to Fonts or Font Software that has been 
modifi ed and is distributed under the “Bitstream Vera” names.
The Font Software may be sold as part of a larger software package but no copy of one or more of the Font 
Software typefaces may be sold by itself.
THE FONT SOFTWARE IS PROVIDED “AS IS”, WITHOUT WARRANT Y OF ANY KIND, EXPRESS OR 
IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTIES OF MERCHANTABILIT Y, FITNESS FOR A 
PARTICUL AR PURPOSE AND NONINFRINGEMENT OF COPYRIGHT, PATENT, TRADEMARK, OR OTHER 
RIGHT. IN NO EVENT SHALL BITSTREAM OR THE GNOME FOUNDATION BE LIABLE FOR ANY CL AIM, 
DAMAGES OR OTHER LIABILIT Y, INCLUDING ANY GENERAL, SPECIAL, INDIRECT, INCIDENTAL, OR 
CONSEQUENTIAL DAMAGES, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING 
FROM, OUT OF THE USE OR INABILIT Y TO USE THE FONT SOFT WARE OR FROM OTHER DEALINGS IN 
THE FONT SOFT WARE.
Except as contained in this notice, the names of Gnome, the Gnome Foundation, and Bitstream Inc., shall 
not be used in advertising or otherwise to promote the sale, use or other dealings in this Font Software 
without prior written authorization from the Gnome Foundation or Bitstream Inc., respectively. For further 
information, contact: fonts at gnome dot org. 
						

							10
How to Access the PDF Operation Manuals
PDF operation manuals in several languages are included in the CD-ROM. To 
utilize these manuals, you need to install Adobe® Reader® on your computer 
(Windows® or Macintosh®).
Please download Adobe
® Reader® from the Internet (http://www.adobe.com).
Accessing the PDF Manuals
For Windows®:
1  Insert the CD-ROM in the CD-ROM drive.
2  Double click the “My Computer” icon.
3  Double click the “CD-ROM” drive.
4 When you want to view the operation 
manual
1)  Double click the “MANUALS” folder.
2)  Double click the language (name of the 
folder) that you want to view.
3)  Double click the pdf fi le to access the 
projector manuals.
 When you want to view the SETUP 
MANUAL
1)  Double click the “SETUP” folder.
2)  Double click the language (name of the 
folder) that you want to view.
3)  Double click the pdf fi le to access the 
SETUP MANUAL.For Macintosh®:
1  Insert the CD-ROM in the CD-ROM drive.
2  Double click the “CD-ROM” icon.
3 When you want to view the operation 
manual
1)  Double click the “MANUALS” folder.
2)  Double click the language (name of the 
folder) that you want to view.
3)  Double click the pdf fi le to access the 
projector manuals.
 When you want to view the SETUP 
MANUAL
1)  Double click the “SETUP” folder.
2)  Double click the language (name of the 
folder) that you want to view.
3)  Double click the pdf fi le to access the 
SETUP MANUAL.
If the desired pdf  le cannot be opened by double clicking the mouse, start Adobe® Reader®  r s t ,  
then specify the desired  le using the “File”, “Open” menu. 
Note
SETUP MANUAL
Refer to the “SETUP MANUAL” contained on the supplied CD-ROM for details.
Connecting Pin Assignments ······················································· 2
RS-232C Speci cations and Commands ····································· 4
Operating the Projector Using the PJLink
TM Protocol ·················· 10
Setting up the Projector Network Environment ·························· 11
Controlling the Projector via L AN ··············································· 17
Resetting the Lamp Timer of the Projector via L AN···················· 22
Troubleshooting ·········································································· 24 
						

							11
IntroductionAccessories
Supplied accessories
Power cord*
For U.S. and 
Canada, etc. 
(6 (1.8 m))
For Europe, 
except U.K. 
(6 (1.8 m))
For U.K. and 
Singapore 
(6 (1.8 m))
For Australia, New 
Zealand and Oceania
(6 (1.8 m))
 (1) (2) (3) (4)
*   Which power cords are supplied along with your projector depends on the region. Use the power 
cord that corresponds to the wall outlet in your country.
Operation manuals (this manual , OPERATION MANUAL FOR STEREOSCOPIC 
3D PROJECTION  and CD-ROM ) 
Remote control 

Two R-6 batteries
 (“A A” size, UM/SUM-3, 
HP-7 or similar)
RGB cable 
(10 (3.0 m)) 

DIN-D-sub  RS-232C  adaptor     
(5 57/64 (15 cm))
Storage case 

Codes in “<  >” are Replacement parts codes. 
Note
Optional accessories
■ Lamp unit
■ Ceiling-mount adaptor
■ Ceiling-mount bracket
■ Ceiling-mount unit
■ Ceiling-mount extension tube
■ Remote receiver
■ 3 RCA to mini D-sub 15 pin cable (10n (3.0 m))AN-D350LP
AN-60KT
AN-XRCM30 (for U.S.A. only)
AN-TK201 
AN-TK202 
AN-EP101B  
(for U.S.A. only)
AN-MR2
AN-C3CP2
Some of the optional accessories may not be available depending on the region. Please check with 
your nearest Sharp Authorized Projector Dealer or Service Center. 
Note 
						

							12
Part Names and Functions
Numbers in Z refer to the main pages in this operation manual where the 
topic is explained.
2
45 6 3
789
1
11
12
13
15 14
10
16
17
18
19
2
45 6 3
789
1
11
12
13
15 14
10
16
17
18
19
Front View
  1   Exhaust vent 57
  2   Zoom ring 28    For enlarging/reducing the picture.
  3  Focus ring 27    For adjusting the focus.
  4   Lens shutter 26, 30
  5    HEIGHT ADJUST lever 28
  6   Adjustment foot 28
  7    Remote control sensor 15
  8   Speaker 50
  9   Intake vent 57
To p  V i e w
10  Temperature warning indicator 58
11   Lamp indicator 58
12   Power indicator 58
13  STANDBY/ON button 26   For turning the power on and putting the  
projector into Standby mode.
14  INPUT buttons (P/R) 30    For switching Input mode.
15  AUTO SYNC button 34   For automatically adjusting images when 
connected to a computer.
16  Adjustment buttons (P/R/O/Q) 39    For selecting menu items.
17  ENTER button 39   For setting items selected or adjusted on 
the menu.
18  MENU button 39   For displaying adjustment and setting 
screens.
19  VOL ( Volume) buttons (–O/Q+) 30    For adjusting the speaker sound level. 
						

							13
Introduction
14
9
13 12 11 123 4 5 6 7 8
10
14
9
13 12 11 123 4 5 6 7 8
10
Rear View (Terminals)
1 L AN terminal 25  Terminal for controlling the projector using a 
computer via network.
2 RS-232C terminal 24  Terminal for controlling the projector using a 
computer.
3 USB terminal 35Terminal connecting with the USB terminal 
on the computer for using the supplied 
remote control as the computer mouse.
4  AUDIO OUT terminal 23Audio output terminal of equipment 
connected to the audio input terminal.
5  MONITOR OUT* terminal 23(Output terminal for computer RGB and 
component signals)
Terminal for connecting a monitor.
 COMPUTER/COMPONENT 2* input 
terminal 
21, 22Terminal for computer RGB and component 
signals.
*  You must switch the setting depending on 
whether you are using the terminal for MONITOR 
OUT or COMPUTER/COMPONENT 2 input.
  6   AUDIO 1 input terminal 23
  7   COMPUTER/COMPONENT 1 input 
terminal 21, 22Terminal for computer RGB and 
component signals.
  8   S-VIDEO input terminal 22Terminal for connecting video equipment 
with an S-video terminal.
  9   VIDEO input terminal 22  Terminal for connecting video equipment.
10   AUDIO 2 input terminal 23
11  AC socket 25Connect the supplied power cord.
12   Kensington Security Standard 
connector
13  Rear adjustment foot 28
14  Security bar
Using the Kensington Lock
This projector has a Kensington Security 
Standard connector for use with a 
Kensington MicroSaver Security System. 
Refer to the information that came with the 
system for instructions on how to use it to 
secure the projector.
 
						

							14
2
3
4
7
8
10
6 1
9
11
12
13
14
15
16
18
20
21
22
23
19 17
5
MOUSE/Adjustment buttons (P/R/O/Q) 35, 39For moving the computer cursor when with the 
USB connection (using a USB cable or the 
optional remote receiver).
For selecting and adjusting menu items. 
8
L-CLICK /EFFECT button 35, 33For the Left click when with the USB 
connection (using a USB cable or the optional 
remote receiver).
For changing the pointer or spot area. 
9
KEYSTONE button 29For entering the Keystone Correction 
mode.10
AUTO SYNC button 34, 50For automatically adjusting images when 
connected to a computer.11
FUNCTION button 53For operating and executing a function 
assigned to “FUNCTION Button”.12
ECO+QUIE T but ton 33For lowering the noise of the cooling fan 
and extending the lamp life.13
FREEZE button 34For freezing images.14
AV MUTE button 30For temporarily displaying a black screen 
and turning off the sound.15
VOL +/– ( Volume) buttons 30For adjusting the speaker sound level.16
SPOT button 33For displaying the spotlight.17
ENTER button 39For setting items selected or adjusted on 
the menu.18
R-CLICK/RETURN button 35, 39For the Right click when with the USB 
connection (using a USB cable or the optional 
remote receiver).
For returning to the previous menu screen 
during menu operations. 

19
MENU button 39For displaying adjustment and setting 
screens.20
RESIZE button 31For switching the picture size (NORMAL, 
16:9, e tc.).21
3D MODE button 
See the OPERATION MANUAL FOR 
STEREOSCOPIC 3D PROJECTION 
provided separately.22
PICTURE MODE button 34For selecting the appropriate picture.23
ON button 26For turning the power on.1
STANDBY button 26For putting the projector into the Standby 
mode.2
BREAK TIMER button 33For displaying the break time.4
MAGNIFY buttons 34For enlarging/reducing part of the image.5
PAGE UP/PAGE DOWN buttons 35Same as the [Page Up] and [Page Down] 
keys on a computer keyboard, when with 
the USB connection (using a USB cable or 
the optional remote receiver).6
POINTER button 33For displaying the pointer.7
Part Names and Functions (Continued)
Numbers in Z refer to the main pages in this operation manual where the 
topic is explained.
INPUT buttons ( / ) 30For switching Input mode.3 
						

							15
IntroductionInserting the Batteries
1  Pull down the tab on the cover and remove the 
cover towards the direction of the arrow.
2 Insert the batteries.Insert the batteries making sure the polarities correctly match 
the m and n marks inside the battery compartment.
3  Insert the lower tab of the cover into the opening, 
and lower the cover until it clicks in place.
Incorrect use of the batteries may cause them to leak or explode. 
Please follow the precautions below
Caution
Danger of explosion if battery is incorrectly replaced.
Replace only with alkaline or manganese batteries.
Insert the batteries making sure the polarities correctly match the m and n marks inside the batter y 
compartment.
Batteries of different types have different properties, therefore do not mix batteries of different types.
Do not mix new and old batteries. 
This may shorten the life of new batteries or may cause old batteries to leak.Remove the batteries from the remote control once they have run out, as leaving them in can cause them to leak.Battery  uid from leaked batteries is harmful to skin, therefore ensure you wipe them  rst and then 
remove them using a cloth.
The batteries included with this projector may run down in a short period, depending on how they are kept. 
Be sure to replace them as soon as possible with new batteries.
Remove the batteries from the remote control if you will not be using the remote control for a long time.
Comply with the rules (ordinance) of each local government when disposing of worn-out batteries.









1 
2 
3 
Usable Range
The remote control can be used to control the 
projector within the ranges shown in the 
illustration.
The signal from the remote control can be 
re ected off a screen for easy operation. 
However, the effective distance of the signal 
may differ depending on the screen material. 
Note
When using the remote controlEnsure that you do not drop it or expose it to 
moisture or high temperature.
The remote control may malfunction under a 
 uorescent lamp. In this case, move the 
projector away from the  uorescent lamp. 

Remote control sensor
Remote control signal 
transmitters
Remote control33n (10 m) 30°
30°Remote control sensor
Remote control signal 
transmitters
Remote control33n (10 m) 30°
30° 
						

							16
Easy Start
This section shows the basic operation (projector connecting with the computer). For details, 
see the page described below for each step.
Setup and Projection
In this section, connection of the projector and the computer is explained using one example.
STANDBY button8
KEYSTONE button5 3
ON button
6INPUT buttons
5Adjustment 
buttons 
(P/R/O/Q)
6
INPUT buttons6
STANDBY/ON 
button3
8
Focus ring4
HEIGHT 
ADJUST lever4
Zoom ring4 6
O/Q buttons 
1. Place the projector facing a wall or a screen       _P.  1 8
When connecting equipment other than a computer, see pages 22 and 23.
2. Connect the projector to the computer and plug the power 
cord into the AC socket of the projector
_PP. 21, 25
        On the projector On the remote control
3. Open the lens shutter fully and then turn the projector on
_P.  2 6