Sharp Projector Pg C45x User Manual

							Easy to Use Functions
-77
Initializing the Settings
This function allows you to initialize the settings you have made in the projector.
Returning to the
Default Settings
Select “All Reset” in the “Options (2)”
menu on the menu screen.
➝ For operating the menu screen, see
pages 42 to 45.
Note
•If a password has been set, the pass-
word input box will be displayed when
selecting “All Reset”.
The following items cannot be initialized.
•C. M. S.
•“Lightness”, “Chroma” and “Hue”
respectively saved for Custom 1-3 on the
C.M.S. menu.
•Fine Sync
•Special Modes
•Signal Info
•Options
•Lamp Life
•Anti-Theft
•Language
•Image stored using “Image Capture” 
						

							-78
This function can be used to display all the adjusted settings as a list on the screen.
Displaying the Adjustment Settings
Overview of All Menu
Settings
Select the “Status” menu on the menu
screen and press 
 .
➝ For operating the menu screen, see
pages 42 to 45.
-78 
						

							Appendix
Appendix 
						

							-80
Cleaning the lens

Use a commercially available blower or lens
cleaning paper (for glasses and camera lenses)
for cleaning the lens. Do not use any liquid type
cleaning agents, as they may wear off the coat-
ing film on the surface of the lens.

As the surface of the lens can easily get dam-
aged, be sure not to scrape or hit the lens.
Cleaning the exhaust and intake vents

Use a vacuum cleaner to clean dust from the
exhaust vent and the intake vent.
Maintenance
Cleaning the projector

Be sure to unplug the power cord before clean-
ing the projector.

The cabinet as well as the operation panel is
made of plastic. Avoid using benzene or thinner,
as these can damage the finish on the cabinet.

Do not use volatile agents such as insecticides
on the projector.
Do not attach rubber or plastic items on the pro-
jector for long time.
    The effects of some of the agents in the plastic
may cause damage to the quality or finish of the
projector.

Wipe off dirt gently with a soft flannel cloth.

When the dirt is hard to remove, soak a cloth in a
neutral detergent diluted with water, wring the
cloth well and then wipe the projector.
Strong cleaning detergents may discolor, warp
or damage the coating on the projector.
Make sure to test on a small, inconspicuous area
on the projector before using.
WaxThinner
Neutral detergent
diluted with water
Neutral detergent
Cleaning
Paper 
						

							Appendix
-81
Replacing the Air Filter
Air filter
Ta b
M4
M4
M4
M4
• This projector is equipped with air fil-
ters to ensure the optimal operating
condition of the projector.
• The air filters should be cleaned ev-
ery 100 hours of use. Clean the filters
more often when the projector is used
in a dusty or smoky location.
• Ask your nearest Sharp Authorized
Projector Dealer or Service Center to
exchange the filter (PFILDA005WJZZ)
when it is no longer possible to clean.
Cleaning and replacing
the bottom air filter
1Turn off the power and discon-
nect the power cord.
•Press . Wait until the cooling fan
stops.
2Remove the bottom filter cover.
•Turn over the projector. Grab the tab
and slide open the filter cover in the
direction of the arrow.
3Remove the air filter.
•Pick the air filter up with your fingers
and lift it out of the filter cover.
Power (OFF) button
Power
(OFF)
button Air filter
(not removable) 
						

							4Clean the air filter.
•Clean the dust off the air filter and
cover with a vacuum cleaner extension
hose.
5Replace the air filter.
•Place the air filter underneath the tabs
on the filter cover.
6Replace the filter cover.
•Slide the filter cover in the direction of
the arrow to close it.
Note
•Be sure the filter cover is securely
installed. The power will not turn on
unless it is correctly installed.
•If dust or dirt has collected inside the
bottom air filter (not removable), clean the
filter with a vacuum cleaner extension
hose.
Replacing the Air Filter
-82 
						

							Appendix
-83
Maintenance Indicators

The warning lights on the projector indicate problems inside the projector.

If a problem occurs, either the temperature warning indicator or the lamp replacement indicator will
illuminate red, and the power will turn off. After the power has been turned off, follow the proce-
dures given below.
Temperature warning
indicator Lamp replacement
indicator Power indicator
About the temperature warning indicator
If the temperature inside the pro-
jector increases, due to blockage
of the air vents, or the setting lo-
cation, “
” will blink in the
lower left corner of the picture. If
the temperature keeps on rising,
the lamp will turn off and the tem-
perature warning indicator will
blink, the cooling fan will run for
further 90 seconds, then the power
will be shut off. After “
” ap-
pears, be sure to perform the fol-
lowing measures.
About the lamp
replacement indicator

The lamp life becomes 0%, when used
for approximately 2,000 hours with “ON”
in “Power Save” or when used for approxi-
mately 1,500 hours with “OFF” in “Power
Save” (see page 69).

When the remaining lamp life becomes
6% or less, “
” will be displayed on the
screen in yellow. When the percentage
becomes 0%, “
” will change to “”
(red), the lamp will automatically turn off
and then the projector as well. At this time,
the lamp replacement indicator will illu-
minate in red.

If you try to turn on the projector a fourth
time without replacing the lamp, the pro-
jector will not turn on.
Maintenance indicator Condition Problem Possible Solution
Temperature
warning
indicatorNormalAbnormal
OffRed on/
Power offThe internal
temperature is
abnormally high. Abnormal
• Blocked air intake•Relocate the projector to an area
with proper ventilation.
•Cooling fan break-
down
•Internal circuit failure
•Clogged air intake•Take the projector to your nearest
Sharp Authorized Projector Dealer
or Service Center (see page 96)
for repair.
Lamp
replacement
indicator
Red on/
Power offThe lamp does
not illuminate.•Burnt-out lamp
•Lamp circuit failure•Carefully replace the lamp. (See
page 86)
•Take the projector to your nearest
Sharp Authorized Projector Dealer
or Service Center (see page 96)
for repair.
•Please exercise care when
replacing the lamp.
Green on
Green
blinks
when the
lamp is
active.Red blinks/
Red onTime to change
the lamp•Remaining lamp life
becomes 6% or
under.
Power
indicatorThe power
indicator blinks
in red when the
projector is on.•The filter cover, lamp
unit cover or lens
cover is open.•Securely install the covers.
•If the power indicator blinks even
when the filter cover is securely
installed, contact your nearest
Sharp Authorized Projector Dealer
or Service Center for advice. Green on/
Red onRed blinks 
						

							-84
Maintenance Indicators
Info
•If the temperature warning indicator illuminates, and the power turns off, follow the above possible solutions
and then wait until the projector has cooled down completely before plugging in the power cord and  turning
the power back on. (At least 5 minutes.)
•If the power is turned off and then turned on again, as during a brief test, the lamp replacement indicator may
be triggered, preventing the power from going on. Should this occur, take the power cord out of the wall outlet
and plug it back in again.
•If you want to clean the air vents during projector operation, be sure to first press 
 and after the power has
turned off and the cooling fan has stopped, then clean the vents.
•Do not unplug the power cord after the power has been turned off and while the cooling fan is running. The
cooling fan runs for about 90 seconds. 
						

							Appendix
-85
Lamp

It is recommended that the lamp (sold separately) be replaced when the remaining lamp life be-
comes 6% or less, or when you notice a significant deterioration in the picture and color quality. The
lamp life (percentage) can be checked with the on-screen display. See page 70.

For lamp replacement, please consult your nearest Sharp Authorized Projector Dealer or Service
Center.
IMPORTANT NOTE TO U.S. CUSTOMERS:
The lamp included with this projector is backed by a 90-day parts and labor limited warranty. All service
of this projector under warranty, including lamp replacement, must be obtained through a Sharp Autho-
rized Projector Dealer or Service Center. For the name of the nearest Sharp Authorized Projector Dealer
or Service Center, please call toll-free: 1-888-GO-SHARP (1-888-467-4277).
U.S.A. ONLY
Caution Concerning the Lamp

This projector utilizes a pressurized mercury lamp. A loud sound may indicate lamp failure. Lamp
failure can be attributed to numerous sources such as: excessive shock, improper cooling, surface
scratches or deterioration of the lamp due to a lapse of usage time. The period of time up to failure
largely varies depending on the individual lamp and/or the condition and the frequency of use. It is
important to note that failure can often result in the bulb cracking.

When the lamp replacement indicator and on-screen display icon are illuminated or flash, it is rec-
ommended that the lamp be replaced with a new one immediately, even if the lamp appears to be
operating normally.

Should the lamp break, the glass particles may spread inside the lamp cage or gas contained in the
lamp may be vented into the room from the exhaust vent. Because the gas in this lamp includes
mercury, ventilate the room well if the lamp breaks and avoid all exposure to the released gas. In
case of exposure to the gas, consult with a doctor as soon as possible.

Should the lamp break, there is also a possibility that glass particles may spread inside of the
projector. In such a case, it is recommended you contact your nearest Sharp Authorized Projector
Dealer or Service Center to remove the damaged lamp and assure safe operation.
Replacing the Lamp
Caution
•Do not remove the lamp unit immediately after operation of the projector. The lamp will be hot and touching
it can lead to burn or injury.
•Wait at least one hour after the power cord is disconnected to allow the surface of the lamp unit to fully cool
before removing the lamp unit.

If the new lamp does not light after replacement, take your projector to the nearest Sharp Autho-
rized Projector Dealer or Service Center for repair. Purchase a replacement lamp unit of type BQC-
XGC50X//1 from your nearest Sharp Authorized Projector Dealer or Service Center. Then carefully
change the lamp by following the instructions described in this section. If you wish, you may have
the lamp replaced at your nearest Sharp Authorized Projector Dealer or Service Center.
Regarding the Lamp 
						

							Power (OFF) button
Lamp
unitBQC-XGC50X//1
User service screw
Removing and Install-
ing the Lamp Unit
Info
•Be sure to remove the lamp unit by the
handle. Be sure not to touch the glass
surface of the lamp unit or the inside of
the projector.
•To avoid injury to yourself and damage
to the lamp, be sure to carefully follow
the steps below.
•Do not loosen other screws except for the
lamp unit cover and lamp unit.
(Only the silver screws are loosened).
•Please refer to the installation manual
included with the lamp unit.
1Press  on the projector to
turn off the power.
•Wait until the cooling fan stops.
Warning!
•Do not remove the lamp unit from the
projector right after use. The lamp will
be very hot and may cause burn or
injury.
2Disconnect the power cord.
•Unplug the power cord from the AC
socket.
•Leave the lamp until it has fully cooled
down (about 1 hour).
3Change the air filter.
•Change the air filter whenever you in-
stall the lamp unit (see pages 81 and
82).
4Remove the lamp unit cover.
•Loosen the user service screw that
secures the lamp unit cover. Then
open the cover in the direction of the
arrow.
AC socket
-86
Regarding the Lamp