Sharp Projector Pg C355w User Manual

							-19
Setup
Projection (PRJ) Mode
The projector can use any of the 4 projection modes, shown in the diagram below. Select the mode most appro-
priate for the projection setting in use.  (You can set the PRJ mode in “SCR-ADJ” menu. See page 50.)
■Table mounted, front projection■Ceiling mounted, front projection
[Menu item ➞ “Front”] [Menu item ➞ “Ceiling + Front”]
■Table mounted, rear projection■Ceiling mounted, rear projection
(with a translucent screen) (with a translucent screen)
[Menu item ➞ “Rear”] [Menu item ➞ “Ceiling + Rear”]
Indication of the Projection Image Size and Projection Distance
For details, refer to the “SETUP MANUAL” contained on the supplied CD-ROM.
Example: 16:10 Signal Input (Normal Mode) for standard lens
500
200
100
80
40
424×265
Projection Distance
170×10685×5368×4234×21
617–7311
(18.8 m – 22.5 m)
248–297
(7.5 m – 9.0 m)124–149
(3.8 m – 4.5 m)910–1110
(3.0 m 
– 3.6 m)411–511
(1.5 m – 1.8 m)
Picture Size 
						

							-20
Standard Zoom Lens
F1.7-F1.9, f=28.0-33.6 mm
16:10 Signal Input (Normal Mode)
The formula for picture size and projection distance
[m/cm]
L1 (m) = 0.03755
χL2 (m) = 0.04507χH (cm) = –0.03209χ[Feet/inches]
L1 (ft) = 0.03755χ / 0.3048
L2 (ft) = 0.04507χ / 0.3048
H (in) = –0.03209χ / 2.54
χ
: Picture size (diag.) (in/cm)
L: Projection distance(m/ft)
L1: Minimum projection distance (m/ft)
L2: Maximum projection distance (m/ft)
H: Distance from the lens center to the bottom of the image (cm/in)
The formula for picture size and projection distance
[m/cm]
L1 (m) = 0.04251
χL2 (m) = 0.05102χH (cm) = –0.03633χ[Feet/inches]
L1 (ft) = 0.04251χ / 0.3048
L2 (ft) = 0.05102χ / 0.3048
H (in) =  –0.03633χ / 2.54
χ
: Picture size (diag.) (in/cm)
L: Projection distance(m/ft)
L1: Minimum projection distance (m/ft)
L2: Maximum projection distance (m/ft)
H: Distance from the lens center to the bottom of the image (cm/in)
4:3 Signal Input (Normal Mode)
Setting Up the Projector
Picture (Screen) size Projection distance [L] Distance from the lens center
to the bottom of  the image [H]
Diag. [x] Width Height Minimum [L1] Maxmum [L2]
500 (1270 cm) 1077 cm (424) 673 cm (265) 18.8 m (61 7) 22.5 m (73 11)
–16 cm (–6 5/16)
400 (1016 cm) 862 cm (339) 538 cm (212) 15.0 m (49 3) 18.0 m (59 2)–13 cm (–5 3/64)
300 (762 cm) 646 cm (254) 404 cm (159) 11.3 m (37 0) 13.5 m (44 4)–10 cm (–3 51/64)
250 (635 cm) 538 cm (212) 337 cm (132) 9.4 m (30 10) 11.3 m (37 0)–8 cm (–3 5/32)
200 (508 cm) 431 cm (170) 269 cm (106) 7.5 m (24 8) 9.0 m (29 7)–6 cm (–2 17/32)
150 (381 cm) 323 cm (127) 202 cm (79) 5.6 m (18 6) 6.8 m (22 2)–5 cm (–1 57/64)
120 (305 cm) 258 cm (102) 162 cm (64) 4.5 m (14 9) 5.4 m (17 9)–4 cm (–1 33/64)
100 (254 cm) 215 cm (85) 135 cm (53) 3.8 m (12 4) 4.5 m (14 9)–3 cm (–1 17/64)
80 (203 cm) 172 cm (68) 108 cm (42) 3.0 m (9 10) 3.6 m (11 10)–3 cm (–1 1/64)
60 (152 cm) 129 cm (51) 81 cm (32) 2.3 m (7 5) 2.7 m (8 10)–2 cm (–49/64)
40 (102 cm) 86 cm (34) 54 cm (21) 1.5 m (4 11) 1.8 m (5 11)–1 cm (–1/2)
Distance from the lens center
to the bottom of  the image [H]Picture (Screen) size Projection distance [L]
Diag. [x] Width Height Minimum [L1] Maxmum [L2]
400 (1016 cm) 813 cm (320) 610 cm (240) 17.0 m (55 9) 20.4 m (66 11)
–15 cm (–5 23/32)
300 (762 cm) 610 cm (240) 457 cm (180) 12.8 m (41 10) 15.3 m (50 3)–11 cm (–4 19/64)
250 (635 cm) 508 cm (200) 381 cm (150) 10.6 m (34 10) 12.8 m (41 10)–9 cm (–3 37/64)
200 (508 cm) 406 cm (160) 305 cm (120) 8.5 m (27 11) 10.2 m (33 6)–7 cm (–2 55/64)
150 (381 cm) 305 cm (120) 229 cm (90) 6.4 m (20 11) 7.7 m (25 1)–5 cm (–2 9/64)
120 (305 cm) 244 cm (96) 183 cm (72) 5.1 m (16 9) 6.1 m (20 1)–4 cm (–1 23/32)
100 (254 cm) 203 cm (80) 152 cm (60) 4.3 m (13 11) 5.1 m (16 9)–4 cm (–1 7/16)
80 (203 cm) 163 cm (64) 122 cm (48) 3.4 m (11 2) 4.1 m (13 5)–3 cm (–1 9/64)
70 (178 cm) 142 cm (56) 107 cm (42) 3.0 m (9 9) 3.6 m (11 9)–3 cm (–1)
60 (152 cm) 122 cm (48) 91 cm (36) 2.6 m (8 4) 3.1 m (10 1)–2 cm (–55/64)
40 (102 cm) 81 cm (32) 61 cm (24) 1.7 m (5 7) 2.0 m (6 8)–1 cm (–37/64)
Note
•
Allow a margin of error in the value in the diagrams above.
• When the distance from the lens center to the bottom of the image [H] is\
 a negative number, this indicates
that the bottom of the image is below the lens center.
• See page 
18  about projection distance [L] and distance from the lens center to the b\
ottom of the image [H]. 
						

							-21
Connections
Samples of Cables for Connection
•For more details of connection and cables, refer to the operation manual of the connecting equipment.
•You may need other cables or connectors not listed below.
Terminal on the
projector
COMPUTER/
COMPONENT 1, 2
DVI-D
AUDIO
(for COMPUTER/
COMPONENT 1, 2, DVI-D)
DVI-D
COMPUTER/
COMPONENT 1, 2
S-VIDEO
VIDEO Equipment
Computer
Audio-visual
equipment
Terminal on
connected equipment
RGB
output
terminal
DVI digital
video
output
terminal
Audio
output
terminal
DVI digital
video
output
terminal
Component
video
output
terminal
Terminal
for using
the
dedicated
cable
S-video
output
terminal
Video
output
terminal
Cable
RGB cable (supplied)
DVI Digital cable (commercially available)
ø3.5 mm stereo or mono audio cable (commercially
available or available as Sharp service part
QCNWGA038WJPZ)
DVI Digital cable (commercially available)
3 RCA to 15-pin D-sub cable (optional: AN-C3CP2)
Connect with the cable adaptor, etc.
S-video cable (commercially available)
Video cable (commercially available)
Cable adaptor (commercially available)
3 RCA to 15-pin
D-sub cable
(optional: AN-C3CP2)
Dedicated cable 
						

							-22
Terminal on the
projector
AUDIO
(for COMPUTER/
COMPONENT 1, 2, DVI-D)
AUDIO
 (for VIDEO, S-VIDEO)
MONITOR OUTPUT
AUDIO
(MONITOR OUT) Equipment
Audio-visual
equipment
Monitor
Amplifier
Terminal on
connected equipment
Audio
output
terminal
Terminal
for using
the
dedicated
cable
Audio
output
terminal
Terminal
for using
the
dedicated
cable
RGB
input
terminal
Audio
input
terminal
Cable
ø3.5 mm stereo minijack to RCA audio cable
(commercially available)
Connect with the cable adaptor, etc.
RCA audio cable (commercially available)
Connect with the cable adaptor, etc.
RGB cable (supplied or commercially available)
ø3.5 mm stereo minijack to RCA audio cable
(commercially available)
Cable adaptor
(commercially available) ø3.5 mm stereo minijack to RCA audio
cable (commercially available)
Dedicated cable
Cable adaptor
(commercially available)
RCA audio cable
(commercially available) Dedicated cable
Samples of Cables for Connection 
						

							-23
Connections
Connecting to a Computer
Before connecting, ensure the power cord of the projector from the AC outlet is unplugged,
and that the devices to be connected are turned off. After making all connections, turn on the
projector and then the other devices. When connecting a computer, ensure that it is the last
device to be turned on after all the connections are made.
Ensure the operation manuals of the devices to be connected have been read before making connections.
When connecting with the RGB cable
(Connecting to COMPUTER/COMPONENT 1 or 2: The illustration shown below is for the former.)
To audio output terminalTo RGB output terminal
* ø3.5 mm stereo or mono audio cable 
  (commercially available or available as Sharp service part QCNWGA038W\
JPZ) To COMPUTER/
COMPONENT 1
input terminal
Computer
To AUDIO input terminal
RGB cable
* When using the ø3.5 mm mono audio cable, the volume level will be half of when using the ø3.5 mm stereo audio cable.
Note
• See page  65 “Computer Compatibility Chart” for a list of computer signals compatible with the projector.
Use with computer signals other than those listed may cause some of the functions to not work.
• A Macintosh adaptor may be required for use with some Macintosh computers. Contact your nearest
Macintosh Dealer.
• Depending on the computer you are using, an image may not be projected unless the computer’s
external output port is switched on. (e.g. Press “Fn” and “F5” keys simultaneously when using a
SHARP notebook computer).  Refer to the specific instructions in your computer’s operation manual to
enable your computer’s external output port.
RGB cableSupplied
accessory 
						

							-24
When connecting with a DVI digital cable
The projector employs the DVI digital input terminal for direct input of Digital Video signals from a
computer.
*When using the ø3.5 mm mono audio cable, the volume level will be half of when using the ø3.5 mm stereo audio cable.
Computer
* ø3.5 mm stereo or mono audio cable 
(commercially available or available as 
Sharp service part QCNWGA038WJPZ)To DVI-D input terminal 
DVI Digital cable 
(commercially available)  To DVI digital
output terminal
To audio output 
terminal
To AUDIO input terminal 
(for DVI-D)
Connecting to a Computer 
						

							-25
Connections
Connecting to Video Equipment
The image quality is highest in order of the Component signal, the RGB s\
ignal, the S-video signal and the
Video signal. If your audio-visual equipment has a component output terminal or RGB output terminal, use the
COMPUTER/COMPONENT terminal 1 or 2 on the projector for video connection.
When connecting video equipment with a DVI output terminal
Note
•Select the input signal type of the video equipment. See page  47.
• While the projector is connected to video equipment that has an HDMI out\
put terminal, only the video
signal can be input to the projector. (Connect the AUDIO input terminal for audio input.)
• Depending on specifications of video equipment or HDMI to DVI digital cable, the signal transmission
may not work property. (The HDMI specification does not support all connections to video equipment
that has HDMI digital output terminal using HDMI to DVI digital cable.)
• For details on compatibility for connection, see support information on DVI connection provided by the
video equipment manufacturer.
When connecting video equipment with component video output terminal
(Connecting to COMPUTER/COMPONENT 1 or 2: The illustration shown below is for the former.)
Note
• When you connect video equipment with a 21-pin RGB output (Euro-scart) to the projector, use a
commercially available cable that fits in the projector terminal you want to connect.
• The projector does not support RGBC signals via the Euro-scart.
DVI Digital cable (commercially available) 
To audio output terminals
ø3.5 mm stereo minijack to RCA audio cable 
(commercially available)To DVI output terminal
Video Equipment
To DVI-D 
input terminal To AUDIO input terminal 
(for COMPUTER/COMPONENT 2, DVI-D)
To audio output terminal
ø3.5 mm minijack to RCA audio cable (commercially available)3 RCA (Component) to 15-pin D-sub cable
(optional: AN-C3CP2)
To component video output terminal
To COMPUTER/COMPONENT 1
input terminal To AUDIO
input terminal
Video Equipment 
						

							-26
When connecting video equipment with S-video output terminal
When connecting video equipment with video output terminal
Note
•When you connect video equipment with a 21-pin RGB output (Euro-scart) to the projector, use a com-
mercially available cable that fits in the projector terminal you want to connect.
RCA audio cable 
(commercially available) To audio output terminal
To S-video output terminal
S-video cable (commercially available)To S-VIDEO input terminal
To AUDIO input terminal
Video Equipment
RCA audio cable 
(commercially available) To audio output terminal
To video output terminal
Composite video cable (commercially available)To VIDEO input terminal
To AUDIO input terminal
Video Equipment
Connecting to Video Equipment 
						

							-27
Connections
Controlling the Projector by a Computer
When the RS-232C terminal on the projector is connected to a computer, the computer can be used to control
the projector and check the status of the projector. Refer to the “SETUP MANUAL” contained on the supplied
CD-ROM for “RS-232C Specifications and Commands”.
When connecting to a computer using an RS-232C serial control cable and a DIN-D-sub RS-232C adaptor
Note
•The RS-232C function may not operate if your computer terminal is not correctly set up. Refer to the
operation manual of the computer for details.
Info
•Do not connect the RS-232C cable to a port other than the RS-232C terminal on the computer. This may
damage your computer or projector.
•Do not connect or disconnect an RS-232C serial control cable to or from the computer while it is on. This
may damage your computer.
Computer
To RS-232C terminalTo RS-232C terminal
RS-232C serial control cable (cross type, commercially available)DIN-D-sub
RS-232C adaptor
DIN-D-sub
RS232C adaptorSupplied
accessory 
						

							-28
To RGB input terminal
RGB cable (commercially available)RGB cable To RGB output 
terminalTo COMPUTER/
COMPONENT 1
input  terminalTo MONITOR OUT terminal
MonitorComputer
When connecting to the LAN terminal using a LAN cable
Note
•When connecting to hub, use straight-through Category 5 (CAT.5) type cable (commercially available).
•When connecting to computer, use cross-over Category 5 (CAT.5) type cable (commercially available).
TX/RX LED (yellow)
Illuminates when transmitting/receiving data.
LINK LED (green)
Illuminates when linked.
To LAN terminal LAN cable (Category 5 type, commercially available)
HUB
or
Computer
*To ensure safety, do not connect the
LAN terminal with any cables such
as a telephone line that may cause
excessive voltage.
RGB cableSupplied
accessory
Connecting to a Monitor with RGB Input Terminal
You can display computer images on both the projector and a separate monitor using two sets of RGB cables.
Controlling the Projector by a Computer