Sharp Pn G655e Operation Manual

ENGLISH
E
19

LANGUAGE
Sets the display language for the menu screen.
ID No. SET
Assigns ID numbers to monitors connected in a daisy chain 
(see page 26), using RS-232C cables.
The numbers 1 to 255 are available for ID numbers.
If “0” is set, the system regards this as the state where no ID 
number is set.
PICTURE FLIP
A picture flips to appear.
STANDARDMIRROR
ROTATEUPSIDE DOWN
ABCABC
ABCABC
POWER ON DELAY
You can delay the screen display after the monitor is turned 
on. The period can be set up to 60...

E
20

Menu Items
TIPS
•  When WHITE BALANCE is set to THRU, BLACK LEVEL, CONTRAST and GAMMA cannot be set.
•  If COLOR MODE is set to sRGB or VIVID, the following 
items cannot be set. 
WHITE BALANCE, PRESET, R-/G-/B-CONTRAST, COPY 
TO USER, and GAMMA
Dual screen display
You can display the screens of the PC input signal and AV 
input signal simultaneously.
Set this function with “PIP MODES” in the PIP/PbyP menu.
PIP
Main screen
Sub screen
A sub screen is displayed 
inside a main screen.
PbyP
Main...

ENGLISH
E
21

Menu Items
Enlarge
You can align 4, 9, 16, or 25 monitors and integrate them into a single large screen to display.
Enlarged views of separated images are displayed in each monitor.
1
3
0
2
4 monitors
9 monitors
16 monitors
25 monitors
012
456
8910
3
7
11
12131415
012
567
101112
3
8
13
15161718
20212223
4
9
14
19
24
Original image
012
345
678
TIPS
• AV input signals cannot be used for the Enlarge function.
• To integrate 9 or more monitors using PC1 signals, a splitter for the video...

E
22

Menu Items
SCHEDULE
You can set the time to switch the monitor on and off.
Set this function with “SCHEDULE” in the OPTION menu. (See 
page 19.)
SCHEDULE
No.POWERDAY OF THE WEEKTIMEINPUT
XXXX/XX/XX XXX  XX:XX:XX PC2 ANALOG
(2)
OK…
[MENU]
1 0 2 4 x 7 6 8 V: 60 Hz    H: 48.4 kHz
(1)(3) (4)(5)
1.  Press  or  to select the SCHEDULE number, and 
press .
2.  Set the SCHEDULE. (See the description below.)
Press  or  to select items, and press  or  to 
change the setting.
3.  Press MENU.
SCHEDULE becomes...

ENGLISH
E
23

Adjustments for PC screen display
Automatic adjustment
When you use the PC2 input terminal or PC3 input terminals 
to display a PC screen for the first time, or when you change 
the setting of the PC, use the automatic screen adjustment.
1. Switch the input to PC2 or to PC3 and display the 
adjustment pattern. (See the description below.)
2. Press MENU and use  or  to display the SCREEN 
menu.
3.  Press 
 and select “AUTO”.
4.  Press 
.
  The automatic adjustment is complete in several...

24E
Initialisation (Reset)/Functional Restriction Setting
You can return the settings to their factory-preset values and 
restrict operations.
1. After pressing SIZE for about 5 seconds, press  , 
 ,  , and  in that order.
OFF
ON
ON
UNLOCKE
D
FUNCTION1/1
ALL RESET
ADJUSTMENT LOCK
OSD DISPLA
Y
LED
RS-232
C
END···[MENU]
2. Select and set the items.
ALL RESET
Resets the settings to the factory default settings.
Press  , select “ON” and then press MENU .
After initialisation, turn the main power switch off...

ENGLISH
25E
Controlling the Monitor with a PC
You can control this monitor from a PC via RS-232C (COM 
port) on the PC.
You can also connect multiple monitors via a daisy chain by 
using a PC. By assigning ID numbers to each monitor (see 
page 26), you can make input mode selection/adjustment or 
can check the status of a specific monitor.
PC connection
One-to-one connection with a PC
Connect with RS-232C straight cable between the PC’s COM 
port (RS-232C connector) and the RS-232C input terminal on...

E
26

Controlling the Monitor with a PC
Response code format
When a command has been executed correctly
O KReturn code(0DH, 0AH)
A response is returned after a command is executed.
*  If an ID number has been assigned
O KSPC 0 01
ID number of responding monitor
Space (20H)Return code(0DH, 0AH)
When a command has not been executed
R REReturn code(0DH, 0AH)
*  If an ID number has been assigned
R RESPC 0 01
ID number
Space (20H)Return code(0DH, 0AH)
TIPS
•  “ERR” is returned when there is no relevant...

ENGLISH
E
27

Controlling the Monitor with a PC
Commands for ID control
The command examples shown on this page assume the 
following connection and ID number set up.
ID number: 1ID number: 2 ID number: 3ID number: 4
IDST ......... A monitor receiving this command sets its own ID 
number in the parameter field.
 Example:
IDST0001
OK 001←The ID number of this monitor is set to 1.
TIPS
You can automatically assign ID numbers by using the IDST 
command with the Repeater control (see “Repeater control” 
on...

E
28

Controlling the Monitor with a PC
Repeater control
This system has a function to allow setting of multiple 
monitors connected in a daisy chain using a single command. 
This function is called repeater control. You can use Repeater 
control function without assigning ID numbers.
[Example]
Set 1Set 2Set 3Set 4
*   If monitors are connected as shown above, you can execute a command like “Set all monitors’ input settings to 
PC1 DIGITAL”.
Repeater control command
Repeater control is achieved by...