Sharp Pn E421 Operation Manual
Have a look at the manual Sharp Pn E421 Operation Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 615 Sharp manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
9E ENGLISH Connecting Peripheral Equipment Connection when the PN-ZB01 (optional) is attached The PN-ZB01 expansion board (optional) allows the use of additional connection terminals. 6. PC/AV DVI-D input terminal • Set DVI of INPUT SELECT on the OPTION menu according to the device to be connected. • Select the audio input terminal to be used in PC DVI-D or AV DVI-D of AUDIO SELECT on the OPTION menu. 7. PC RGB input terminals • Set BNC of INPUT SELECT on the OPTION menu to PC RGB when using the PC RGB input terminals. • Select the audio input terminal to be used in PC RGB of AUDIO SELECT on the OPTION menu. 8. AV component input terminals • Set BNC of INPUT SELECT on the OPTION menu to AV COMPONENT when using the AV component input terminals. • Select the audio input terminal to be used in AV COMPONENT of AUDIO SELECT on the OPTION menu. 9. AV video input terminal • Select the audio input terminal to be used in AV VIDEO of AUDIO SELECT on the OPTION menu. 10. AV S-video input terminal • Select the audio input terminal to be used in AV S-VIDEO of AUDIO SELECT on the OPTION menu. 11. Audio1 input terminals / Audio2 input terminals • Set the audio input terminal to be used in each input mode in AUDIO SELECT on the OPTION menu. 12. LAN terminal • You can control the monitor from a PC on a network by connecting a commercially available LAN cable between this terminal and a network. 13. External speaker terminals • To use external speakers, set SPEAKER SELECT on the SETUP menu to EXTERNAL. • Be sure to use external speakers with an impedance of 6 Ω or greater and a rated input of at least 10 W. 13 2Approx. 3-15/16 inch (10 cm) 1. Attach a speaker cable core (included with the PN-ZB01) to the end of the speaker cable connected to the monitor. 2. While pushing the tab, insert the tip of the cable. 3. Release the tab. TIPS • Be sure to connect the + and - terminals and the left and right speakers properly. • Avoid short circuiting the + and - terminals. • When SPEAKER SELECT is set to EXTERNAL, the internal speakers are disabled. 14. PC/AV DVI-D output terminal • The video of the PC/AV DVI-D input can be output to an external device. • Outputting HDCP-encrypted video requires an external device which supports HDCP. • This terminal allows the daisy chain connection of up to 5 monitors. TIPS • The length of the signal cables or surrounding environment may affect the image quality. • The screen may not display properly when using terminals other than PC DVI-D/AV DVI-D for the input mode. In this case, turn off the power to all the monitors connected in a daisy chain and then turn the power on again. • When connecting monitors in a daisy chain set AUTO INPUT CHANGE to OFF. • Video output is disabled in the following cases: When the input mode is PC HDMI/AV HDMI When PIP SOURCE of the PIP/PbyP menu is set to PC HDMI or AV HDMI When the power is turned off When the monitor is in input signal waiting mode
10E Connecting the Power Cord Caution • Do not use a power cord other than the one supplied with the monitor. 1. Turn off the main power switch. 2. Plug the power cord (supplied) into the AC input terminal. 3. Plug the power cord (supplied) into the AC power outlet. Binding Cables AC input terminal 1 Main power switch Power cord (Supplied) For power outlet 2 3 Removing the Handles The handles can be removed. The removed handles can be attached on the rear side. Caution • The removed handles and handle screws are for use with this monitor. Do not use them for any other devices. • To attach handles, be sure to use the handles and handle screws which were removed from the monitor. • Be sure the handles are attached securely. Handle Handle screws Handle Handle screws [PN-E471] Cable clamp attachment [PN-E421] Cable clamp attachment The cables connected to the terminals on the rear of the monitor can be fastened with the cable clamp. Insert the cable clamp into the cable clamp attachment on the rear of the monitor and fasten the cables. Cable clamp Cable clamp attachment Cable
ENGLISH 11E Preparing the Remote Control Unit Installing the batteries 1. Press the cover gently and slide it in the direction of the arrow. 2. See the instructions in the compartment and put in the supplied batteries (R-03 (“AAA” size) x 2) with their plus (+) and minus (-) sides oriented correctly. 3. Close the cover. TIPS • When the batteries become exhausted replace them with new (commercially available) batteries. • The supplied batteries (R-03 (“AAA” size) x 2) may become exhausted quickly depending on how they are stored. • If you will not be using the remote control for a long time, remove the batteries. • Use manganese or alkaline batteries only. Remote control operation range The operation range of the remote control unit is approx. 16.4 feet (5 m) at an angle of approx 10° from the center to the top/ bottom/right/left of the remote control sensor. 10°1 0° 10° 10° Remote control sensor 16.4 feet (5 m) TIPS • Do not expose the remote control unit to shock by dropping or stepping on it. This could lead to a malfunction. • Do not expose the remote control unit to liquids, and do not place it in an area with high humidity. • The remote control unit may not work properly if the remote control sensor is under direct sunlight or strong lighting. • Objects between the remote control unit and the remote control sensor may prevent proper operation. • Replace the batteries when they run low as this may shorten the remote control’s operation range. • If a fluorescent light is illuminated near the remote control unit, it may interfere with proper operation. • Do not use it with the remote control of other equipment such as air conditioner, stereo components, etc. Affixing the Stand Hole Protection Covers After installing the monitor, affix the stand hole protection covers as necessary. 1. Peel off the backing sheet and affix the cover on the monitor.
12E Turning Power On/Off Caution • Turn on the monitor first before turning on the PC or playback device. Turning on the main power Main power switch Caution • The main power must be turned on/off with the main power switch. Do not connect/disconnect the power cord or turn the breaker on/off while the main power switch is on. • When switching the main power switch or the POWER button off and back on, always wait for at least 5 seconds. Turning power on/off Press the POWER button to turn the power ON/OFF. When the main power switch is off, the monitor cannot be turned on using the POWER button on the remote control unit. Power LED Status of a power LED Status of the monitor Green lighting Power on Orange lighting Power off (Standby mode) Green flashing Input signal waiting mode Caution • When switching the main power switch or the POWER button off and back on, always wait for at least 5 seconds. A short interval may result in a malfunction. TIPS • If the monitor is in the input signal standby mode and you press the POWER button on the remote control unit, the monitor enters standby mode. • You can turn on/off the monitor by pressing the power switch on the front panel of the monitor. • Setting the SCHEDULE flashes the power LED alternately in red and orange in standby mode. nDate/time setting • If the time has yet to be set when the monitor is first turned on, the date/time setting screen appears. Set the date and time. DA TE/TIME SETTING SET CANCE L 09 // OK···[MENU] 20 01 / 01 / 00 00 : : : 1. Press , , or to select the date and time, and press or to change the numerical values. 2. Select SET and then press . • Be sure to set the date and time. • The date/time setting screen will close automatically if no operation is performed for about 15 seconds. The date and time can be set using DATE/TIME SETTING from the OPTION menu when the date/time setting screen disappears. TIPS • Set the date in “Year/Month/Day” order. • Set the time on a 24-hour basis. • The clock is maintained by the internal battery. • If you already set the time but the date/time setting screen appears when the power is turned on, the internal battery may be exhausted. Please contact your local Sharp servicing dealer or service center for assistance with battery replacement. • Estimated service life of the internal battery: About 5 years (depending on monitor operation) • As the first battery was inserted at the factory, it may be exhausted prior to the expected continuous operation life. Disabling power on/off operations Power on/power off operations can be disabled in order to protect the monitor from an accidental power off. Set the ADJUSTMENT LOCK in FUNCTION menu to “2”. (See Operation guide.)
Printed in China Imprimé en Chine Impreso en China Gedruckt in China Отпечатано в Китае 0NY42M184305B(1) Q41G42M1843 5B