Sharp Pg Mb60x Projector User Manual

-57
Useful Features
Setting the Audio Output
Type
This function determines whether the audio level
output from the AUDIO OUTPUT terminal is fixed
or variable by linking with VOLUME.
Menu operation  Page 42
Example: “Options2” screen menu
Description of Audio Out Settings
Info
•When “Audio Out” has been set to “VAO”, first make
sure to lower the volume of the projector before
turning the power on or off and when switching the
input.
Description
Audio output that does not vary in
strength with the volume...

-58
Selecting the Transmis-
sion Speed (RS-232C)
Make sure that both the projector and computer
are set for the same baud rate.
Menu operation  Page 42
Example: “Options2” screen menu
Description of RS-232C
Note
•Refer to the “SETUP GUIDE” contained on the
supplied CD-ROM for RS-232C Specifications
and Command Settings.
•Refer to the computer’s operation manual for
instructions for setting the computer’s baud rate.
Description
Transmission speed is slow.
Transmission speed is rapid.Selectable items
9600...

-59
Useful Features
Returning to the Default
Settings
This function allows you to initialize the settings
you have made in the projector.
Menu operation  Page 42
Example: “Options2” screen menu
Note
The following items or menu cannot be initialized.
•“Fine Sync” menu
Special Modes
• “Options1” menu
Lamp Timer  (Life)
System Lock
• “Language” menu 

-60
Selecting the On-screen
Display Language
The projector can switch the on-screen display
language among 11 languages: English, German,
Spanish, Dutch, French, Italian, Swedish, Portu-
guese, Chinese, Korean or Japanese.
Example: “Language” screen menu for
INPUT 1 (RGB) mode
1Press  on the remote control.
•The “Picture” menu will be displayed.
2Press \ or | to select the “Lan-
guage” menu icon (
).
•The “Language” menu will be displayed.
3Press ' or " to select the desired
language, and then...

-61
Appendix
Cleaning the lens
■Use a commercially available blower or lens clean-
ing paper (for glasses and camera lenses) for clean-
ing the lens. Do not use any liquid type cleaning
agents, as they may wear off the coating film on the
surface of the lens.
■As the surface of the lens can easily get damaged,
ensure not to scrape or hit the lens.
Cleaning the exhaust and intake vents
■Use a vacuum cleaner to clean dust from the ex-
haust vent and the intake vent.
Info
•If you want to clean the air vents...

-62
Power indicator
Lamp indicator
Temperature warning indicator
Maintenance Indicators
Maintenance Indicators
■The warning lights on the projector indicate problems inside the projector.
■If a problem occurs, either the temperature indicator or the lamp indicator will illuminate red, and
the projector will enter the standby mode. After the projector has entered the standby mode, follow
the procedures given below.
About the temperature warning indicator
If the temperature inside the projector increases,...

-63
Appendix
Maintenance indicator
Problem
Cause Possible solution
Temperature
warning
indicatorNormalAbnormal
OffRed on
(Standby)The internal
temperature is
abnormally high. Abnormal
• Blocked air intake•Relocate the projector to an area
with proper ventilation (see page
7).
•Cooling fan break-
down
•Internal circuit failure
•Clogged air intake•Take the projector to your nearest
Sharp Authorized Projector Dealer
or Service Center (see page 70)
for repair.
•Clean the exhaust and intake
vents. (See page...

-64
Lamp
■It is recommended that the lamp unit (optional: AN-MB60LP) be replaced when the remaining lamp
life becomes 5% or less, or when you notice a significant deterioration in the picture and color
quality. The lamp life (percentage) can be checked with the on-screen display. See page 49.
■Purchase a replacement lamp unit of type AN-MB60LP from your place of purchase, nearest Sharp
Authorized Projector Dealer or Service Center.
IMPORTANT NOTE TO U.S. CUSTOMERS:
The lamp included with this projector...

-65
Appendix
Optional
accessoryLamp unit
AN-MB60LPRemoving and Installing
the Lamp Unit
Info
•Ensure the lamp unit is removed using the
handle. Ensure the glass surface of the
lamp unit or the inside of the projector are
not touched.
•To avoid injury to yourself and damage to
the lamp, ensure to carefully follow the
steps below.
•Do not loosen other screws except for the
lamp unit cover and lamp unit.
1Press  on the projector or
 on the remote control to put
the projector into standby mode.
•Wait until...

-66
4Remove the lamp unit.
•Loosen the securing screws from the
lamp unit. Hold the lamp unit by the
handle and pull it in the direction of the
arrow. At this time, keep the lamp unit
horizontal and do not tilt it.
5Insert the new lamp unit.
•Press the lamp unit firmly into the lamp
unit compartment. Fasten the securing
screws.
6Replace the lamp unit cover.
•Align the lamp unit cover and slide it to
close. Then tighten the user service
screw to secure the lamp unit cover.
Info
•If the lamp unit and lamp...