Sharp MX M283N User Manual

2-49
COPIER
Contents
3
Select Dual Page Copy.
(1) Touch the [Special Modes] key.
☞SPECIAL MODES (page 2-41)
(2) Touch the [Dual Page Copy] key so that it is 
highlighted.
(3) Touch the [OK] key.
You will return to the base screen of copy mode.
4
Press the [START] key.
Copying will begin.
If you have selected sort mode, change originals and press the [START] key. Repeat until all pages have been scanned and 
then touch the [Read-End] key.
To cancel scanning of the original and copying...
Press the [STOP]...

2-50
COPIER
Contents
MAKING COPIES IN PAMPHLET FORMAT 
(Pamphlet Copy)
This function copies 2 original pages onto the front side and 2 original pages onto the reverse side of each sheet of 
paper so that the copies can be folded at the centreline to form a pamphlet.
This function is convenient for arranging copies into an attractive booklet or pamphlet.
Pamphlet copy using 8 original pages
1
Place the original.
Place the original face up in the document feeder tray, or face down on the document glass.
If...

2-51
COPIER
Contents
3
Select pamphlet copy settings.
(1) If the original is 1-sided, touch the [1-Sided] 
key. If the original is 2-sided, touch the 
[2-Sided] key.
(2) Select the binding edge ([Left Binding] or 
[Right Binding]).
(3) To insert a cover, touch the [Cover Setting] 
key.
If you do not want to add a cover, go to step 5.
4
Select cover settings.
(1) If the cover sheet will be copied on, touch 
the [Yes] key. Otherwise, touch the [No] 
key.
(2) Select paper settings for the cover.
(A) The...

2-52
COPIER
Contents
5
Touch the [OK] key.
You will return to the base screen of copy mode.
6
Press the [START] key.
Copying will begin.
If you are using the document glass, change originals and press the [START] key. Repeat until all pages have been scanned 
and then touch the [Read-End] key.
To cancel scanning of the original and copying...
Press the [STOP] key ( ).
 To make pamphlet copies of a book or other bound original, use the book copy function.
 When the pamphlet copy function is selected,...

2-53
COPIER
Contents
COPYING A LARGE NUMBER OF 
ORIGINALS AT ONCE (Job Build)
When copying a very large number of originals, this function allows you to divide the originals into sets and feed each 
set through the automatic document feeder one set at a time.
Use this function when you wish to copy all of the originals as a single job but the number of originals exceeds the 
maximum number that can be inserted.
This function is convenient when you wish to sort copies of a large number of originals into...

2-54
COPIER
Contents
4
Insert the next set of originals and press the [START] key.
Repeat this step until all originals have been scanned.
The copy settings (Exposure, Paper Select, and Copy Ratio only) can be changed for each set of originals. If you need 
to change the copy setting, follow the steps in Changing the copy settings for each set of originals.
To cancel scanning...
Press the [STOP] key ( ). All scanned data will be cleared.
5
Touch the [Read-End] key.
To cancel copying...
Press the [STOP]...

2-55
COPIER
Contents Changing the copy settings for each set of originals
The copy settings (Exposure, Paper Select, and Copy Ratio only) can be changed for each set of originals.
Perform the step below before pressing the [Start] key to scan the originals in step 4 above.
1
Touch the [Change] key.
2
Change the desired copy settings in the 
screen that appears and press the [Start] 
key.
Scanning of the originals will begin using the changed copy 
settings.
To cancel the copy setting changes and begin...

2-56
COPIER
Contents
USING TWO MACHINES TO MAKE A LARGE 
NUMBER OF COPIES (Tandem Copy)
Two machines connected to the same network can be used to run a large copy job in parallel.
Each machine prints half of the copies, reducing the time required to complete the job.
Master machine and slave machine
In the following explanation, the master machine is the machine that is used to scan the originals. The slave machine is 
another machine specified in the master machine that only helps print the copies; it...

2-57
COPIER
Contents
3
Set the number of copies (number of 
sets) with the numeric keys.
Up to 999 copies (sets) can be set. When the [START] key is 
pressed, the copies will automatically be divided between the 
master and slave machines.
If an odd number of copies is set, the master machine will print 
the extra set.
If an incorrect number of copies is set...
Press the [CLEAR] key ( ) and then enter the correct number.
4
Press the [START] key.
Copying will begin.
If you are using the document glass,...

2-58
COPIER
Contents
In this situation...
A punch module is installed on the master machine but not on the slave machine.
 Copying without punching: tandem copy is possible.
 Copying with punching: tandem copy is not possible.
In this way, if tandem copying is executed using a function that the slave machine does not have, a message will appear. To 
have the master machine make all copies, touch the [OK] key. To cancel the job, touch the [Cancel] key.
If a machine runs out of paper
If either the master...