Sharp MX M282N User Manual

39
MAINTENANCE
REPLACING THE TONER COLLECTION CONTAINER
The toner collection container collects excess toner that is produced during printing. When the toner collection container 
becomes full, Replace used toner container. will appear. Follow the procedure below to replace the toner collection 
container.
1Open the front cover.
2Remove the toner collection container. 
(1) Tilt the toner collection container forward.
Grasp the corners of the toner collection container with 
both hands as shown and tilt...

40
MAINTENANCE
5Plug the hole in the toner collection 
container with the cap.
Push the cap in firmly so that toner will not leak out.
Do not discard the toner collection container. Place it in a plastic bag and keep it until your service technician comes to 
perform maintenance. Your service technician will collect the toner collection container.
6Install the new toner collection 
container.
Insert the box from above at a slant. 
7Push the toner collection container into 
the machine.
Push the box in...

41
MAINTENANCE
REPLACING THE STAMP CARTRIDGE
If a stamp unit (AR-SU1) is installed on the automatic document feeder and the stamp has become faint, replace the 
stamp cartridge (AR-SV1).
Supplies
Stamp cartridge (2 in package) AR-SV1
1Open the automatic document feeder.
2Open the holders on the automatic 
document feeder that hold the original 
pressure sheet.
Open the holders (two) on the left and right sides.
3Grasp the tab on the stamp unit and pull 
the unit out.
4Remove the stamp cartridge (A).
Tab...

42
MAINTENANCE
5Install a new stamp cartridge.
6Push the stamp unit back in.
Push the stamp unit in until it clicks into place.
7Replace the original pressure sheet.
Push the holders in until they click into place.
8Close the automatic document feeder.
Downloaded From ManualsPrinter.com Manuals 

43
REMOVING MISFEEDS
When a paper misfeed occurs, the message A misfeed has occurred. will appear in the touch panel and printing and 
scanning will stop. In this event, touch the [Information] key in the touch panel. When the key is touched, instructions for 
removing the misfeed will appear. Follow the instructions. When the misfeed is cleared, the message will automatically 
clear.
The blinking   mark in the image at left indicates the approximate position of the misfeed.
For detailed procedures for...

44
SUPPLIES
Standard supplies for this product that can replaced by the user include paper, toner cartridges, and staple cartridges for 
the finisher.
Be sure to use only SHARP-specified products for the toner cartridges, finisher staple cartridge, saddle stitch finisher 
staple cartridge, and transparency film.
Storage of supplies
Proper storage
1. Store the supplies in a location that is: clean and dry,
 at a stable temperature,
 not exposed to direct sunlight.
2. Store paper in the wrapper and lying...

45
SPECIFICATIONS
Machine specifications / copier specifications
*1 Warm-up time may vary depending on some environments.
*2 First print time may vary depending on the status of the machine.
NameDigital Multifunctional System MX-M282N/MX-M362N/MX-M452N/MX-M502N
TypeDesktop
Photoconductive typeOPC drum
Printing methodElectrophotographic system (laser)
Developer systemDry-type two-component magnetic brush development
Fusing systemHeat rollers
Scanning resolutionDocument glass600 x 300 dpi (factory default...

46
SPECIFICATIONS
Machine specifications / copier specifications (Continued)
*1 Output tray (Centre tray) cannot be used when the finisher or saddle stitch finisher is installed.
*2 Type A connectors are located on the front of the machine and on the right side of the machine at the back (total of two connectors).
Do not use the connectors simultaneously.
When a keyboard is not connected (MX-KBX2), only one connector can be used; simultaneous use is not possible. If you need to 
change the connector that...

47
SPECIFICATIONS
Continuous copying speeds*
* Copy speed during output of the second copy and following copies when performing continuous one-sided copying of the same page (excluding offset output) using plain one-sided paper from a tray other than the bypass tray.
Chemical emission (measured according to RAL UZ-122: Edition Jan. 2006)
ModelMX-M282N MX-M362N MX-M452NMX-M502N
Copy ratio100% / Reduced / Enlarged
 A3, 11 x 17, 8K15 copies/min. 17 copies/min. 20 copies/min. 22 copies/min.
B4, 8-1/2 x 14,...

48
SPECIFICATIONS
Acoustic noise emission (measurement according to ISO7779)
Reversing single feeder specifications (MX-RP11)
*1 Scanning in mono 2 mode of one side only is possible in fax and scan send modes. However, when the resolution is 600 x 600 dpi 
in Internet fax mode, the maximum length is 800 mm (31-31/64). When the resolution is 400 x 400 dpi or 600 x 600 dpi in scan 
mode, a long original cannot be scanned.
*2 Paper weights from 35 g/m
2 (9 lbs.) to 49 g/m2 (13 lbs.) require the use of slow...