Sharp Lc42sb48uta Manual

							 41
Specifications
ItemLC-32SB28UT-ALC-42SB48UT-A
LCD screen size32” Class (31 1/2” Diagonal)  Active Matrix (a-Si TFT LCD)42” Class (42 1/50” Diagonal)  Active Matrix (a-Si TFT LCD)
Resolution1,049,088 pixels  (1,366 x 768)2,073,600 pixels  (1,920 x 1080)
TV Function
Receiving SystemAmerican TV Standard ATSC/NTSC System
Receiving Channel
VHF/UHFVHF 2-13ch, UHF 14-69ch
CATV1-125ch (non-scrambled channel only)Digital Terrestrial Broadcast (8VSB)2-69ch
Digital cable*1 (64/256 QAM)1-135ch (non-scrambled channel only)
Audio multiplexBTSC SystemAudio out5W x 5W5W x 5W
Terminals
Rear
ANT/CABLE75 q Unbalance,F Type x 1 for Analog (VHF/UHF/CATV) and Digital (AIR/CABLE)INPUT 2COMPONENT in, AUDIO inINPUT 3COMPONENT in, AUDIO in
INPUT 415-pin mini D-sub female connector,  Audio in ( Ø 3.5mm jack)INPUT 5HDMI in with HDCP, Audio in ( Ø 3.5mm jack)INPUT 6HDMI in with HDCP, Audio in ( Ø 3.5mm jack)INPUT 7HDMI in with HDCP, Audio in ( Ø 3.5mm jack)OUTPUTRCA (L/R) jack / Digital Audio outputRS-232CD-sub 9 pin for service & Hotel mode using
Side
INPUT 1AV in, AUDIO inUSBMulti-Media use, Software updateEarphone OutputØ 3.5mm jack (Audio output)INPUT 8HDMI in with HDCP, Audio in ( Ø 3.5mm jack)OSD languageEnglish/French/SpanishPower Requirement120V @ 60Hz
Power Consumption85 W  (< 0.3 W Standby with AC 120 V)185 W  (< 0.3 W Standby with AC 120 V)
WeightTV + stand23.71 lbs. /10.755 kg40.03 lbs. /18.16 kg
TV only20.4 lbs. /9.255 kg34.83 lbs. /15.8 kg
Dimension*2 
(W / H / D)
TV + stand31 1/8 x 22 7/16 x 9 7/16 (inch)39 31/32 x 27 11/16 x 10 5/8 (inch)
TV only31 1/8 x 20 3/4 x 3 9/16 (inch)39 31/32 x 25 25/32 x 3 13/16 (inch)
Operating temperature32°F to + 95°F (0°C to + 35°C)
*1 Emergency alert messages via Cable are unreceivable.
*2 The dimensional drawings are shown on the inside back cover.
• As part of policy of continuous improvement, SHARP reserves the right to make design and specification changes for product improvement without prior notice. The performance specification figures indicated are nominal values of production units. There may be some deviations from these values in individual units.
Appendix 
						

							 42
PC Compatibility Chart
It is necessary to set the PC correctly to display XGA and WXGA signal. \
Refer to page 17-18 to set PC input signals.
PCResolutionHorizontal FrequencyVertical FrequencyVESA Standard
PC
VGA
720 x 40031.469 kHz70.087 Hz—
640 x 480
31.469 kHz59.940 HzO
37.861 kHz72.809 HzO
37.500 kHz75.000 HzO
SVGA800 x 600
35.156 kHz56.250 HzO
37.879 kHz60.317 HzO
48.077 kHz72.188 HzO
46.875 kHz75.000 HzO
XGA1024 x 768
48.363 kHz60.004 HzO
56.476 kHz70.069 HzO
60.023 kHz75.029 HzO
WXGA1280 x 76847.396 kHz59.995 HzO
SXGA1280 x 102463.981 kHz60.020 HzO
WXGA1360 x 76847.712 kHz60.015 HzO
HDMIResolutionHorizontal FrequencyVertical FrequencyPixel Clock Frequency
HDMI
VGA640 x 48031.469 kHz60.000 Hz25.175 MHz
SVGA800 x 60037.879 kHz60.000 Hz40.000 MHz
XGA1024 x 76848.363 kHz60.000 Hz65.000 MHz
WXGA1280 x 76847.712 kHz60.000 Hz85.500 MHz
1080P1920 x 1080P67.500 kHz60.000 Hz148.500 MHz
720P1280 x 720P45.000 kHz60.000 Hz74.250 MHz
1080i1920 x 1080i33.750 kHz60.000 Hz74.250 MHz
480P720 x 480P31.500 kHz60.000 Hz27.030 MHz
480i720 x 480i15.750 kHz60.000 Hz13.510 MHz
ComponentResolutionHorizontal FrequencyVertical FrequencyPixel Clock Frequency
Component
720P1280 x 720P45.000 kHz60.000 Hz74.250 MHz
1080i1920 x 1080i33.750 kHz60.000 Hz74.250 MHz
480P720 x 480P31.500 kHz60.000 Hz27.030 MHz
480i720 x 480i15.750 kHz60.000 Hz13.510 MHz
DDC is a registered trademark of Video Electronics Standards Association.
Appendix 
						

							 43
Appendix
RS232 Port Specifications
 45
� PC control of the TV•  Attach an RS-232C cable cross-type (commercially 
available) to the supplied Din/D-Sub RS-232C for the 
connections.
This operation system should be used by a person who is 
accustomed to using computers.
�  Communication conditionsSet the RS-232C communication settings on the PC to 
match the TV's communication conditions.
The TV's communication settings are as follows:
•
� Communication procedure Send the control commands from the PC via the RS-
232C connector.
The TV operates according to the received command 
and sends a response message to the PC.
Do not send multiple commands at the same time. 
Wait until the PC receives the OK response before 
sending the next command.
� ParameterInput the parameter values, aligning left, and fi ll with 
blank(s) for the remainder. (Be sure that 4 values are 
input for the parameter.)
When the input parameter is not within an adjustable 
range, “ERR” returns. (Refer to “Response code format”.)
Any numerical value can replace the “x” on the table.
a
30
0009 0???? ?
When “?” is input for some 
commands, the 
present setting 
value responds.
� 
Command formatEight ASCII codes 
e CR
Command 4-digits Parameter 4-digitsReturn code
C1  C2  C3  C4  P1  P2  P3  P4
Command 4-digits: Command. The text of four characters.
Parameter 4-digits: Parameter 0–9, x, blank, ?
Baud rate:
9,600 bps
Data length: 8 bits
Parity bit: None
Stop bit: 1 bit
Flow control: None
� Command table•  Commands not indicated here are not guaranteed to operate.
� Response code formatNormal response
Return code (0DH) Return code (0DH)
Problem response (communication 
error or incorrect command)
OKERR
If an underbar (_) appears in the parameter column, enter a space.
If an asterisk (*) appears, enter a value in the range indicated in brackets under CONTROL CONTENTS.
Any numerical value can replace the “x” on the table.
•
•
•
CONTROL ITEM
COMMANDPARAMETERCONTROL CONTENTS
POWER ON COMMAND SETTING
POWER SETTING The Power On command rejected.
It input-switches by the toggle. (It is the same as an input change key)
It input-switches to TV. (A channel remains as it is. (Last memory))
It input-switches to INPUT1~INPUT8.
An input change is also included.
Although it can choose now, it is toggle operation in inside.
The screen position variable ranges depend on the View Mode or the 
signal type. The ranges can be seen on the position-setting screen.
0: Although it can choose now, it is toggle operation in inside.
1: Only available when 4:3 signal is being input.
5, 6: Only available when 4:3 signal is being input.
8: [PC] Available except when UXGA is being input. 
    [AV] Only available when 1080i/p is being input.
9: Only available when 720p is being input.
(Toggle)
Input terminal number (1–8)
0: Auto, 1: VIDEO, 2: COMPONENT
0: (Toggle), 1:  STANDARD, 2: MOVIE, 3: GAME, 4: USER, 5: DYNAMIC (Fixed), 6: DYNAMIC, 7: PC, 100: AUTOVolume (0–60)
Only PC mode. (0–180)
Only PC mode. (0–40)
0: (Toggle) [AV], 1: Side Bar [AV], 2: S.Stretch [AV]
3: Zoom [AV], 4: Stretch [AV], 5: Normal [PC]
6: Zoom [PC], 7: Stretch [PC], 
8: Dot by Dot [PC] [AV], 9: Full Screen [AV]
   
An input change is included if it is not TV display.
In Air, 2–69ch is effective.
In Cable, 1–135ch is effective.
If it is not TV display, it will input-switch to TV. (same function as CHU)
If it is not TV display, it will input-switch to TV. (same function as CHV)
Toggle operation of a closed caption.
0: (Toggle), 1: On, 2: Off
0: Off, 1: OFF TIMER – 30 MIN., 2: OFF TIMER – 60 MIN., 
3: OFF TIMER – 90 MIN., 4: OFF TIMER – 120 MIN.The channel number of TV
The channel number of TV +1
The channel number of TV  –1(Toggle) (1–135)
RSPW
I TGD
ITVD
IAVD
INP1
INPUT SELECTION A TOGGLE
INPUT SELECTION B
AV MODE SELECTION
VOLUME
POSITION
VIEW MODE
SURROUND
SLEEP TIMER
CHANNEL
CC DIRECT
(ANALOG)
(DIGITAL)
CH UP
CH DOWN CHANNEL H-POSITION H-POSITION
V-POSITION
CLOCK
PHASE
INPUT 1
AVMDVOLM
HPOS
VPOS
CLCK
PHSE
ACSU
OFTM DCCH
CHUP
CHDW
CLCP
WIDE
0
x
0
*
*
*
*
*
*
*
*
*
*
*
x
x
x *
*
_
_
_ _
_ _ *
*
*
*
*
_
_
_
_
_
_
*
_
_
_ _
_ _ *
*
*
*
_ _
_
_
_
_
_
_ DIGITAL Air (Two-Part numbers, 2-digit plus 2-digit)
(0100-9999)
(1-999)
(0-999)
(0-9999)
(0-6383) DIGITAL Cable (Two-Part numbers, 3-digit plus 3-digit)
DIGITAL Cable (Two-Part numbers, 3-digit plus 3-digit) Front half of DIGITAL CABLE CHANNEL NO. (Designate major channel)
Rear half of DIGITAL CABLE CHANNEL NO. (Designate minor channel)
DIRECT
CHANNEL
DA2P****
DC2U* * *_
DC2L* * *_
DIGITAL Cable (One-Part numbers, 5-digit, less than 10,000)
DC10* * * *
DIGITAL Cable (One-Part numbers, 5-digit, more than 10,000)
DC11* * * *
_
_
_ _
(Toggle)
AUDIO SELECTION
ACHAx___
_0: (Toggle), 1: On, 2: Off
MUTE
MUTE * ____ _
_
_
_ _ _ Off
The Power On command accepted.
1___On
Power On
1 _ _ _ Power On It shifts to standby.
P O W R 0 _ _ _ Power Off
_
_
_
_0: Auto,  2: COMPONENT, 3: S-TERMINAL
INP2
INPUT 2
*___
_
TV
INPUT1-8
RS-232C Port Speci
 cations
Using a PC
-$@@-&6/@&JOEC






Command table™ Commands not indicated here are not guaranteed to operate.CONTROL ITEM COMMANDPARAMETERCONTROL CONTENTS
POWER ON COMMAND SETTING
POWER SETTING The Power On command r
ejected.
It input-switches by the toggle. (It is the same as an input change key\
)
It input-switches to TV . (A channel remains as it is. (Last memory))
It input-switches to INPUT1~INPUT8.
Although it can choose now , it is toggle operation in inside.
The scr een position variable ranges depend on the V iew Mode or the 
signal type. The ranges can be seen on the position-setting scr een.
0: Although it can choose now , it is toggle operation in inside.
1: Only available when 4:3 signal is being input.
5, 6: Only available when 4:3 signal is being input.
8: [PC] A vailable except when UXGA is being input. 
    [A V] Only available when 1080i/p is being input.
9: Only available when 720p is being input.
(T
oggle)
Input terminal number (1–8)
0:  (T ogg le) , 1:   STA N DAR D, 2 : M OVIE , 3 : GA ME, 4 : U SER , 5: DYNAMIC (Fixed), 6: DYNAMIC, 7: PC, 100: AUTOVolume (0–60)
Only PC mode. (0–180)
Only PC mode. (0–40)
0: (T oggle) [A V], 1: Side Bar [A V], 2: S.Stretch [AV]
3: Zoom [A V], 4: Stretch [AV], 5: Normal [PC]
6: Zoom [PC], 7: Str etch [PC], 
8: Dot by Dot [PC] [A V], 9: Full Screen [AV]
   
An input change is included if it is not TV display.
In Air, 2–69ch is ef fective.
In Cable, 1–135ch is ef fective.
If it is not TV display, it will input-switch to TV . (same function as CH +)
If it is not TV display, it will input-switch to TV . (same function as CH -)
T oggle operation of a closed caption.
0: (T
oggle), 1: On, 2: Of f
0: Off, 1: OFF TIMER – 30 MIN., 2: OFF TIMER – 60 MIN., 
3: OFF TIMER – 90 MIN., 4: OFF TIMER – 120 MIN.The channel number of TV
The channel number of TV +1
The channel number of TV  –1(T oggle)
(1–135)
R
SPW
I T G D
I T VD
I A VD
INPUT SELECTION A
TOGGLE
AV MODE SELECTION
VOLUME
POSITION
VIEW MODE
SURROUND
SLEEP TIMER
CHANNEL
CC DIRECT
(ANALOG)
(DIGIT
AL)
CH UP
CH DOWN CHANNEL H-POSITION H-POSITION
V -POSITION
CLOCK
PHASE A
VM D
V O LM
H PO S
V PO S
CL CK
PH SE
AC SU
O FTM
D CC H
C H U P
C H DW
CL CP
W
ID E 0
x
0
*
*
*
*
*
*
*
*
*
*
x
x
x *
*
_
_
_ _
_ _ *
*
*
*
*
_
_
_
_
_
*
_
_
_ _
_ _ *
*
*
*
_ _
_
_
_
_
_ DIGITAL Air (T wo-Part numbers, 2-digit plus 2-digit)
(0100-9999)
(1-999)
(0-999)
(0-9999)
(0-6383) DIGIT
AL Cable (T wo-Part numbers, 3-digit plus 3-digit)
DIGIT AL Cable (T wo-Part numbers, 3-digit plus 3-digit)
Fr
ont half of DIGIT AL CABLE CHANNEL NO. (Designate major channel)
Rear half of DIGIT AL CABLE CHANNEL NO. (Designate minor channel)
DIRECT
CHANNEL
D
A2 P****
D C 2U ***_
D C 2L ***_
DIGITAL Cable (One-Part numbers, 5-digit, less than 10,000)
D
C 10 ****
DIGITAL Cable (One-Part numbers, 5-digit, mor e than 10,000)
D
C 11 ****
_
_
_ _
(Toggle)
AUDIO SELECTION
AC H A x___
_ 0: (T
oggle), 1: On, 2: Of f
MUTE
MUTE *_ _
__ _
_
_
_ _ _
Off
The Power On command accepted.
1 ___On
Power On
1 ___Power On It shifts to standby.
P OW R0___Power Of f
_
_
_
_
TV
INPUT1-8
If an underbar (_) appears in the parameter column, enter a space.• 
If an asterisk (*) appears, enter a value in the range indicated in br\
ackets under CONTROL • CONTENTS.
Any numerical value can replace the “x” on the table.•  
						

							 44
Information on the Software License for This Product
■ Software composition
The software included in this product is comprised of various software c\
omponents whose individual copyrights are held by SHARP or by third parties.
■ Software developed by SHARP and open source software
The copyrights for the software components and various relevant document\
s included with this product that were developed or written by SHARP are owned by S\
HARP and are protected by the Copyright Act, international treaties, and other releva\
nt laws. This product also makes use of freely distributed software and software components wh\
ose copyrights are held by third parties. These include software components covered by \
a GNU General Public License (hereafter GPL), a GNU Lesser General Public License (\
hereafter LGPL) or other license agreement.
■ Obtaining source code
Some of the open source software licensors require the distributor to pr\
ovide the source code with the executable software components. GPL and LGPL includ\
e similar requirements. For information on obtaining the source code for the open \
source software and for obtaining the GPL, LGPL, and other license agreement information\
, visit the following website:
http://www.sharpusa.com/gpl
We are unable to answer any questions about the source code for the open\
 source software. The source code for the software components whose copyrights a\
re held by SHARP is not distributed.
■ Acknowledgements
The following open source software components are included in this produ\
ct:
• linux kernel/busybox/uClibc/zlib/libpng/libjpeg
CLEARING THE SECRET NUMBER
If you forget the secret number, clear the secret number using the follo\
wing procedure.
Press 1. MENU to display the MENU screen, and then press a/b to select “Parental” and press d to enter it.
Press 0000 as a master code, and then press 2. a/b to select “Change Password” and press d to enter it.
Enter a new PIN. (See page 37.)3. 
The secret number is                .
As a precautionary measure, make a note of your secret number above, cut\
 it from this • manual, and keep it in a safe place.
Appendix 
						

							 45
Legal notices
■ FCC Part 15
This device complies with Part 15 of the FCC Rules. Operation of this pr\
oduct is subject to the following two conditions: (1) this device may not cause harmful\
 interference, and (2) this device must accept any interference received, including interferenc\
e that may cause undesired operation.This equipment has been tested and found to comply within the limits for\
 a class B digital device, pursuant to Part 15 of the FCC Rules. These limits are d\
esigned to provide reasonable protection against harmful interference in a resident\
ial installation. This equipment generates, uses, and can radiate radio frequency energy a\
nd, if not installed and used in accordance with the instructions, may cause harmfu\
l interference to radio communications. However, there is no guarantee that interferenc\
e will not occur in a particular installation. If this equipment does cause harmful inter\
ference to radio or television reception, which can be determined by turning the equipmen\
t off and on, the user is encouraged to try to correct the interference by one or more\
 of the following measures:Reorient or relocate the receiving antenna.• 
Increase the separation between the equipment and receiver.• 
Connect the equipment into an outlet on a circuit different from that to\
 which the • receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.• 
■ FCC warning
Changes or modifications not expressly approved by the party responsib\
le for compliance with the FCC Rules could void the user’s authority to operate this eq\
uipment.
■ Cables
Connections to this device must be made with shielded cables with metall\
ic RF/EMI connector hoods to maintain compliance with FCC Rules and Regulations.
■ Canadian notice
This Class B digital apparatus complies with Canadian ICES-003.Cet appareil numérique de la classe B est conforme à la norme NMB-\
003 du Canada.“Standard Television Receiving Apparatus-Appareil de reception tél\
évision ordinaire, Canada BETS-7 / NTMR-7”.
■ DOLBY
 
Manufactured under license from Dolby Laboratories. “Dolby” and th\
e double-D symbol are trademarks of Dolby Laboratories.
■ HDMI
 ®
HDMI, the HDMI logo, and High-Definition Multimedia Interface are trad\
emarks or registered trademarks of HDMI Licensing LLC in the United States and other countries.
Appendix 
						

							 46
For location of the nearest Sharp Authorized Service, or to obtain produ\
ct literature, accessories, supplies, or customer assistance, please call 1-800-BE-SHAR\
P.
LIMITED WARRANTY
Calling for Service
 31
&ORçLOCATIONçOFçTHEçNEARESTç3HARPç!UTHORIZEDç3ERVICEçORçTOçOBTAINçPRODUCTçLITERATUREçACCESSORIESçSUPPLIESçORç
CUSTOMERçASSISTANCEçPLEASEçCALLç

%
3(!20
Calling for Service
LIMITED WARRANTY
For location of the nearest Sharp Authorized Service, or to obtain produ\
ct literature, accessories, supplies, or 
customer assistance, please call 1-800-BE-SHARP.
Calling for Service
LIMITED WARRANTY
CONSUMER LIMITED WARRANTY
SHARP  ELECTRONICS  CORPORATION warrants  to the  rst  consumer  purchaser  that this Sharp  brand Liquid  Crystal  Display  product  (the
“Pr oduct”),  when shipped  in its  original  container , will  be free  from  defective  workmanship  and materials,  and agrees  that  it will,  at its  option, 
either  repair  the defect  or replace  the defective  Product  or part  thereof  with  a new  or remanufactur ed equivalent  at no  char ge to the 
pur chaser for parts or labor for the period(s) set forth belo w.
This  warranty  does not apply  to any  appearance  items of the  Product  or if the  serial  number  or model  number  afxed to the  Produ ct has 
been  removed,  defaced,  changed,  altered or tamper ed with.  This warranty  does not cover  installation  or signal  reception  problem s. This 
limited  warranty  will not  apply  if the  Product  has been  or is being  used in a commer cial setting  or application;  this warranty  is meant  solely 
for  the  non-commer cial, household  use of the  Product  by consumers  in their  home  or residence.  If you  intend  to or  already  use this  Product 
for  commer cial purposes  or in a commer cial setting,  there ar e warranties  available
 to  cover  your use of this  Product,  the terms  of  which  may 
vary . Please contact  1-888-GO-SHARP for further information.
In  order  to enfor ce your  rights  under  this limited  warranty , you  should  follow the steps  set forth  below . You  must  be able  to provide  proof  of 
pur chase to the servicer , which proof must include the date of pur chase. 
T o  the  exte nt  per mitted  b y applicable  s tate  la w,  th e wa rra ntie s s et  fort h a re  in  lie u of ,  a n d  excl usiv e  of ,  all  ot her  w arr an tie s,  exp re ss  o r 
i m plied .  S pecically  A LL  O TH ER  W AR RANTI ES O TH ER  TH AN  TH OS E S ET  F O RTH  ABOVE  ARE EX CLU DED,  ALL EXPR ESS A ND
IMP LIE D  W AR R ANTIE S INC LU DING  TH E W ARR ANTI ES  O F M ER CHAN TA B IL IT Y, FITNE SS F OR  U SE,  A N D FITN ESS F OR  A  P A R TICU LAR  
P UR PO SE A R E S P ECIFIC ALLY  E XC LUD ED .  IF ,  UN DER  A PPL ICAB LE  S TA TE  L A W ,  IM PL IED  W ARR ANTIE S M AY  N O T V AL
ID LY  BE  
D ISCL AIMED  O R E XCLUD ED ,  TH E D UR ATION  OF  SUCH  IM PLIE D W ARRA NTIES IS  L IMIT ED T O  TH E PER IOD (S )  F RO M TH E D AT E  O F 
P URCH AS E S ET  FO RTH  BEL OW .  THI S W AR RA NTY  GIV ES  YO U S PE CIFIC  LE GAL  R IGHT S. YO U M AY  A LSO  H AV E  O TH ER R IGHT S 
W HICH  V A RY F R OM  STA TE  T O  STA T E .
The  warranties  given herein  shall  be the  sole  and exclusive  warranties  granted by Sharp  and shall  be the  sole  and exclusive  rem edy
available  to the  purchaser  and only  for the  time  periods  set forth  herein.  No other  repr esentations  or promises  made by anyone  are 
permitted.  Correction  of defects,  in the  manner  and for the  period  of time  described  herein,  shall  constitute  complete fulllment of all 
liabilities  and responsibilities  of Sharp  to the  purchaser  with respect  to the  Product,  and shall  constitute  full satisfaction  of all  claims, 
whether based on contract, negligence, strict liability or otherwise. Sh\
arp does not warrant nor shall Sharp be liable, or in a ny way
r esponsible,  for Products  which have been  subject  to abuse  (including,  but not limited  to, impr oper
 voltage),  accident,  misuse, negligence, 
lack  of reasonable  care, alteration,  modication,  tampering, misuse, improper  operation  or maintenance  or any  damages  or defect s in  the 
Pr oduct  which  were caused  by repairs  or attempted  repairs  performed  by anyone  other than a Sharp  authorized  servicer. Nor  shall  Sharp 
be  liable  or in any  way  responsible  for any  incidental  or consequential  economic or property  damage.  Some states  do not  allow  limits  on 
warranties or on r emedies for breach in certain transactions; in such states, the limits he rein may not apply .
THIS LIMITED W ARRANTY IS VALID ONLY IN THE FIFTY (50) UNITED ST ATES, THE DISTRICT OF COLUMBIA AND PUER TO RICO.
Model Specic Section
Wher e to Obtain Service: From  a Sharp  Authorized  Servicer located in the  United  States.  To  nd  the 
location  of the  near est Sharp  Authorized  Servicer, please  call Sharp  toll free 
at 1-800-BE-SHARP .
What to do to Obtain Service: Contact your Sharp  Authorized  Servicer to obtain  carry in  service for this 
LC-32SB28UT
product.  The Servicer  will come  to your  location  and if necessary  remove  the 
unit  for repair  at the  Servicer’ s facility  and retur n the  set to you  once 
completed. Be sur e to have Proof of Pur chase available.
Contact  your Sharp  Authorized  Servicer to obtain  in home  service  for this 
LC-42SB48UT
product.  The Servicer  will come  to your  location  and if necessary  remove  the 
unit  for repair  at the  Servicer’ s facility  and retur n the  set to you  once 
completed. Be sur e to have Proof of Pur chase available.
TO OBT AIN PRODUCT INFORMA TION OR PURCHASE ACCESSORIES AND EXTENDED W ARRANTIES, CALL 1-800-BE-SHARPOR VISIT www.sharpusa.com
Additional Exclusions fr om 
W arranty Coverage (if any): In 
order  for the  Product  to be  serviced,  the Product  must be readily  available 
to  the  servicer , free  and  clear  of any  complex  or non-standar d installation, 
mounting  or other  encumbrance  which would  unreasonably  interfere with 
servicing  the Product.  The Servicer  will remount  the Product  after service, 
pr ovided  that such  remounting  is not  into  a complex  or non-standar d installa-
tion.  Any additional  labor and materials  requir ed to remove  and/or reinstall  a 
Pr oduct  above  and beyond  the foregoing  are  not  cover ed by this  warranty , 
may r esult in additional char ges and are the responsibility of the consumer .
Image  Retention  resulting  from  a xed  image  being displayed  for long 
periods  of time  is not  cover ed by this  Limited  Warranty  (see Operation 
Manual on how to pr event this).Warranty Period for this Pr oduct: One (1) year parts and labor from the date of purchase.
Your Pr oduct Model Number & Description: LC-32SB28UT / LC-42SB48UT LCD Color Television
(Be  sure to  have  this information  available when you need  service  for your 
Pr oduct.)
SH AR P E LE C TR O NIC S  CO RPO RATIO NSharp  P laza,  Mah wah,  New  Jer sey  0749 5-11 63
S H AR P C O RPO RATION
-$4#6@&@8BSSBOUZJOEE