Sharp Lc19sk24uw Manual

 11
Part names
POWER
 button
TV (Front)
Channel 
buttons
 (CH
r/
s) 
Volume 
buttons 
(VOL
k/
l)  INPUT
 buttonPOWER indicator** OPC sensor* Remote control sensor
*OPC: Optical Picture Control (See page 26.)
**See page 16 for TV status indicator.OPC indicator**
TV (Side/Rear)
INPUT 4 terminals
(PC IN)
INPUT 1 terminals DIGITAL AUDIO OUTPUT 
terminal
Antenna/Cable in AC INPUT
terminal
INPUT 2 terminals MENU
 buttonINPUT 3 terminals
(HDMI)
HEADPHONE terminal
Regarding the headphone jack
 Use headphones...

 12
Part names
1 POWER: Switch the TV power on or enters standby. 
(See page 16.)
2 DISPLAY: Display the channel  information.           
(See page 18).
3 CC: Display captions from a closed-caption source. 
(See page 41.)
4 0 – 9: Set the channel. (See page 18.)
5  (DOT): (See pages 18.)
6 FLASHBACK: Return to the previous channel or 
external input mode. (See page 18.)
7 VIEW MODE: Select the screen size. (See pages 36 
and 37.)
8 FREEZE: Set the still image. Press again to return to 
normal screen....

Antennas
To enjoy a clearer picture, use an outdoor antenna. The following is a brief explanation of the types of connections 
that are used for a coaxial cable. If your outdoor antenna uses a 75-ohm coaxial cable with an F-type connector, 
plug it into the antenna terminal at the rear of the TV set.
1. A 75-ohm system is generally a round cable with F-type 
connector that can easily be attached to a terminal 
without tools (Commercially available).
F-type connector
300-ohm twin-lead cable ( at) F-type...

L
R AUDIOY
P
B
PR
L
R AUDIO
L
R AUDIO
 14
Preparation
Connecting a Blu-ray disc player, 
HD-DVD player, DVD player or a 
Digital TV STB (Air or Cable)
Connecting a VCR, game console 
or camcorder
A VCR, game console, camcorder and other 
audiovisual equipment can be conveniently connected 
using the INPUT 2 terminals. You can connect many types of external equipment to 
your TV like a Blu-ray disc player, HD-DVD player, DVD 
player, VCR, Digital TV tuner, HDMI equipment, game 
console or camcorder. To...

ANALOG
RGB
( PC IN )
 15
Preparation
PC HDMI equipment
PC compatibility chart
It is necessary to set the PC correctly to display XGA and WXGA signal. Refer to page 40 to set PC input signals.
DDC is a registered trademark of Video Electronics Standards Association.
Power Management is a registered trademark of Sun Microsystems, Inc.
VGA and XGA are registered trademarks of International Business Machines Corp.
PC Horizontal Frequency VESA StandardResolution Vertical Frequency
Connecting a PC
When...

 16 Simple operations for watching a TV program
POWER 
indicator
POWER (On/Standby)
Turning on the power
Press POWER on the TV, or POWER on the remote 
control unit.
 POWER indicator (Green): The TV is on. (After a few 
seconds, a window appears with sound.)
 
 The initial setup starts when the TV powers on for the  rst 
time. If the TV has been turned on before, the EZ Setup will 
not be invoked. See page 25 for performing EZ Setup from 
the Setup menu.
Turning off the power
Press POWER on the TV, or...

Press 
a/
b to select “Analog & Digital” to 
search both analog and digital broadcasts or 
“Analog” to search only analog broadcasts or 
“Digital” to search only digital broadcasts, and 
then press ENTER.
Press 
a/
b to select “Yes” or “No”, and then 
press ENTER.
 The Channel search will start automatically.
 To exit the Channel search screen, press 
RETURN.
 17
Initial setup
When you turn on the TV for the  rst time, it will automatically memorize the broadcasting channels where you live. 
Perform the...

 18
Simple button operations for 
changing channels
You can change channels in several ways. 
 When selecting a 1-digit channel number, it is not 
necessary to press 0 before the number.
0-9 only, channel selection will be made if 
there is no operation within a few seconds.
To select a 3-digit channel number
(e. g., Channel 115):
Press 1
s1
s5
sENT
To select a 4-digit channel number
(e. g., Channel 22.1):
Press 2 
s2
s
s1
sENT
0–9 only, channel selection will be made if 
there is no operation within a...

20
20
20
 19
Simple button operations for 
changing volume/sound
■ Changing the volume
You can change the volume on the TV, or on the 
remote control unit.
VOL
k/
l on the TV operates the same as VOL 
k/
l on 
the remote control unit.
■ Using VOL
k/
l 
 To increase the volume, press VOL
k.
 To decrease the volume, press VOL
l.
Volume display when headphones are plugged in.
Volume adjustment

∅3.5mm).

not in use.

plugged in.  
■ Using MUTE on the remote control unit
Mutes the current sound output....

English
French
Spanish
 20
Setting MTS/SAP stereo mode
The TV has a feature that allows reception of sound 
other than the main audio for the program. This feature 
is called Multi-channel Television Sound (MTS). The TV 
with MTS can receive mono sound, stereo sound and 
Secondary Audio Programs (SAP). The SAP feature 
allows a TV station to broadcast other information, 
which could be audio in another language or something 
completely different like weather information. 
You can enjoy Hi-Fi stereo sound...