Sharp Lc 46x20e Operation Manual

							
Inserting a CA Card
In order to receive coded digital stations, a Common 
Interface Module (CI Module) and a CA Card must be 
inserted in the CI slot of your TV set. (Page 8)
The CI Module and the CA Card are not supplied 
accessories. They are usually available from your 
dealer.
Inserting the CA Card into the CI ModuleWith the side with the gold coloured contact 
chip facing the side of the CI Module marked 
with the provider’s logo, push the CA Card 
into the CI Module as far as it will go. Note the 
direction of the arrow printed on the CA Card.
Inserting the CI Module in the CI slotRemove the rear terminal cover.
Carefully insert the CI Module in the CI slot with 
the contact side forward.
  The logo on the CI Module  must be facing forward from 
the rear of the TV. Do not use 
excessive force. Make sure 
the module is not bent in the 
process.
1
2
3
Checking CI Module information
NOTE
•  Make sure that the CI Module is properly inserted.
•  This menu is only available for digital stations.
Press  MENU  and the menu screen displays.
Press  c/d  to select “Digital Setup”.
•  The content of this menu depends on the provider of 
the CI Module.
Press  a/b  to select “CI Menu”, and then press 
OK .
Press  a/b  to select the following desired item, 
and then press  OK.
1
2
3
4
Connecting external devices
E Module
General information on CI Module displays.
E Menu
Adjustment parameters of each CA CARD displays.
E Enquiry
You can input numerical values such as passwords 
here.
NOTE
• The content of each screen depends on the 
manufacturer of the CI module.
Removing the CI Module
Remove the cover from the rear of 
the set.
Remove the module from the set.
Replace the cover.
1
2
3
 19
LC -4 2X 20E -g b.in dd   1 9LC-42X20E-gb.indd   192007/0 9/0 4   1 6:3 1:2 22007/09/04   16:31:22
 
						

							
Controlling HDMI devices using AQUOS LINK
What is AQUOS LINK?
Using the HDMI CEC (Consumer Electronics Control) protocol, with AQUOS LINK you can 
interactively operate compatible system devices (AV amplifier, DVD, Blu-ray Disc device) 
using a single remote control.
NOTE
•  AQUOS LINK-compatible AQUOS BD Player, AQUOS AUDIO speaker system and AQUOS Recorder are to be on sale after the release of this TV. (As of September 2007)
What you can do with AQUOS LINK
✔  One Touch Recording (DTV only)
You do not have to search for the remote control of your recording device. Press the  REC 
E  or  REC STOP  H buttons inside the flip cover to start/stop recording what you see on 
the recorder.
✔   One Touch Play
While the TV is in standby mode, it automatically turns on and plays back the image from 
the HDMI source.
✔  Single remote control operation
The AQUOS LINK automatically recognises the connected HDMI device and you can 
control the TV and the devices as if using a universal remote control.
✔  Operating Title list of external devices
In addition to displaying the TV’s own Timer list (Page 12), you can also call up the 
external player’s Top menu or AQUOS BD Player’s/AQUOS Recorder’s Title list provided 
that the devices support AQUOS LINK.
✔  Multiple control of HDMI devices
You can select which HDMI device to operate using the  OPTION button.
NOTE
•  Point the remote control toward the TV, not to the connected HDMI device.
•  Video noise may occur depending on the type of HDMI cable used. Make sure to use a certified 
HDMI cable.
•  Up to 3 HDMI recording devices, one AV amplifier and two players can be connected using this  system.
•  These operations affect the HDMI device selected as the current external source. If the device  does not operate, turn on the device and select the appropriate external source using  b.
•  When you insert/remove HDMI cables or change connections, turn on all connected HDMI  devices before turning on the TV. Confirm that picture and audio are correctly output by selecting 
“EXT4”, “EXT5” or “EXT6” from the INPUT SOURCE menu.
AQUOS LINK
 20
LC -4 2X 20E -g b.in dd   2 0LC-42X20E-gb.indd   202007/0 9/0 4   1 6:3 1:2 22007/09/04   16:31:22
 
						

							
Connecting an AQUOS BD 
Player/AQUOS Recorder only
HDMI cable
AQUOS AUDIO 
speaker system
Connecting an AQUOS BD Player/AQUOS Recorder via the 
AQUOS AUDIO speaker system
HDMI cable
AQUOS BD Player/ 
AQUOS Recorder
HDMI cable
Optical AUDIO 
cable
AQUOS LINK
AQUOS LINK Auto power on
If this is activated, the One Touch Play function 
is enabled. While the TV is in standby mode, it 
automatically turns on and plays back the image from 
the HDMI source.
Press  MENU  and the menu screen displays.
Press  c/d  to select “Option”.
Press  a/b  to select “AQUOS LINK Setup”, and 
then press  OK.
Press  a/b  to select “Auto Power On”, and 
then press  OK.
Press  c/d  to select “On”, and then press  OK.
NOTE
•  The factory default for this item is “Off”.
Selecting recorder
Here, you can select a recorder for the recording from 
several connected recorders.
1
2
3
4
5
Repeat steps 1 to 3 in  AQUOS LINK Auto 
power on .
Press  a/b  to select “Selecting Recorder”, and 
then press  OK.
Select the recorder, and then press  OK.
NOTE
•  If you have connected the AQUOS AUDIO speaker system 
between the TV and an AQUOS Recorder, the external 
source’s indication changes from “EXT5” to “EXT5 (Sub)”.
Using Genre Info.
This function allows you to automatically switch to 
the appropriate sound mode depending on the genre 
information included the digital broadcast.
Repeat steps 1 to 3 in  AQUOS LINK Auto 
power on .
Press  a/b  to select “Using Genre Info.”, and 
then press  OK.
Press  c/d  to select “On”, and then press  OK.
1
2
3
1
2
3
AQUOS LINK Setup
AQUOS LINK connection
First connect the AQUOS AUDIO speaker system or an AQUOS BD Player/AQUOS\
 Recorder that supports the 
HDMI CEC protocol.
NOTE
•  Refer to the operation manual of the device to be connected for further \
details.
•  After unplugging connection cables or changing the connection pattern, first turn on the power of the TV with all relevant 
device’s power turned on. Change the external input source by pressing  b, select the appropriate external source and 
verify the audiovisual output.
•  The cables illustrated in the following explanation are commercially available items.
AQUOS BD Player/ 
AQUOS Recorder
 21
L C -4 2X 20E -g b.in dd   2 1LC-42X20E-gb.indd   212007/0 9/0 4   1 6:3 1:2 22007/09/04   16:31:22
 
						

							
AQUOS LINK
Operating an AQUOS LINK device
AQUOS LINK allows you to operate the HDMI-
connected device with one remote control.Open the remote control’s flip cover.
Press  PLAY  I to start playback of a title.
•  See the right column, section “ Playback of titles 
using AQUOS LINK ” if you want to start playback 
using the list of the titles of the AQUOS BD Player/
AQUOS Recorder.
Press  FWD J  to fast forward.
 Press  REV G  to reverse.
 Press  STOP H  to stop.
 Press  B to turn the HDMI-connected device 
on/off.
Listening with the AQUOS AUDIO speaker 
system
You can opt to listen to the TV sound only from the 
AQUOS AUDIO speaker system.
Open the remote control’s flip cover.
Press  OPTION .
AQUOS LINK Menu 
Recorder EPG
Top Menu/Title List 
Media change 
By AQUOS AUDIO SP
By AQUOS SP
Sound mode change 
Model select 
Press  a/b  to select “By AQUOS AUDIO SP”, 
and then press  OK.
•  The sound from the TV speaker and headphone 
terminal is silenced and only the sound from the 
AQUOS AUDIO speaker system is audible.
Listening with the AQUOS TV speaker 
system
You can opt to listen to the TV sound only from the 
AQUOS TV speaker system.
Open the remote control’s flip cover.
Press  OPTION .
•  The AQUOS LINK Menu displays.
Press a/b  to select “By AQUOS SP”, and then 
press  OK.
Manually changing the AQUOS AUDIO 
speaker system’s sound mode
Open the remote control’s flip cover.
Press  OPTION .
•  The AQUOS LINK Menu displays.
Press a/b  to select “Sound mode change”.
The sound mode changes every time you press 
OK .
•  Refer to the operation manual of the AQUOS AUDIO 
speaker system for details.
1
2
3
1
2
3
1
2
3
1
2
3
4
Playback of titles using AQUOS LINK
This section explains how to play back a title in the 
AQUOS BD Player/AQUOS Recorder.
Open the remote control’s flip cover.
Press  OPTION .
•  The AQUOS LINK Menu displays.
Press a/b  to select “Top Menu/Title List”, and 
then press  OK.
•  The linked recorder now powers on and the TV 
automatically selects the appropriate external input 
source.
•  The title list data from the connected AQUOS BD  Player/AQUOS Recorder displays.
Select the title with  a/b /c /d , and then press 
PLAY  I.
Selecting media type for CEC-compatible 
recorder
If your recorder has multiple storage media, select the 
media type here.
Open the remote control’s flip cover.
Press  OPTION .
•  The AQUOS LINK Menu displays.
Press a/b  to select “Media change”, and then 
press  OK.
Select the desired medium, such as DVD or 
HDD. The media type changes every time you 
press  OK.
HDMI device selection
If multiple HDMI devices are connected in a daisy 
chain, you can specify which device to control here.
Open the remote control’s flip cover.
Press  OPTION .
•  The AQUOS LINK Menu displays.
Press a/b  to select “Model select”, and then 
press  OK. The HDMI device changes every time 
you press  OK.
Recording via the AQUOS Recorder EPG 
(only for recorders)
You can call up the CEC-compatible recorder’s EPG 
and preset timer recordings using the TV’s remote 
control.
Open the remote control’s flip cover.
Press  OPTION .
•  The AQUOS LINK Menu displays.
Press a/b  to select “Recorder EPG”, and then 
press  OK.
•  The external input source switches and the recorder’s 
EPG is displayed.
Select the programme to record.•  Refer to the operation manual of the recorder for details.
1
2
3
4
1
2
3
4
1
2
3
1
2
3
4
 22
LC -4 2X 20E -g b.in dd   2 2LC-42X20E-gb.indd   222007/0 9/0 4   1 6:3 1:2 32007/09/04   16:31:23
 
						

							
Menu operation
What is the Menu?
• You need to bring up the On-Screen Display to perform settings for the TV. The On-Screen Display for the settings is called “Menu”.
• The Menu enables various settings and adjustments.
• The Menu can be operated with the remote control unit.
Common operations
1
MENU  [ Picture ]
Picture Audio
Contrast OPC [Off]
Brightness
Colour
Tint
Sharpness
Advanced
Reset [+30]
[0]
[0]
[0]
[0]
0
–30
–30
–30
–10 +40
+30
+30
+30
+10
Backlight [+14] –16
+16
DYNAMIC
MENU    [
Power Control  ... No Operation Off]Power Control
Setup
No Signal Off
No Operation Off
Ecology
Sleep Timer [Disable]
[Disable]
Analogue Search
Digital Search
Display the Menu 
Screen
Press  MENU  and the MENU screen 
displays.
3Exit the Menu  screen
The operation will exit the menu 
screen if you press  END before it is 
completed.
2
Select an item
Press  a/b /c /d  to select/adjust the 
desired menu, and adjust the item to 
the desired level, and then press  OK.
Press  6 to return to the previous 
Menu page.
About the Guide Display
The Guide Display at the bottom of the screen shows 
operations with an On-Screen Display.
The bar above is an operational guide for the remote control. 
The bar will change in accordance with each menu setting 
screen.
OK: Select  : Enter MENU : End 6: Back 
E Selecting in the Menu
E Selecting options
Operation without a remote control
This function is useful when there is 
no remote control within your 
reach.
Press  MENU  briefly to display 
the direct control screen.
Press  P r /s  instead of  a/b  or  i  k /l 
instead of  c/d  to select the item.
Press  b to complete the setting.
NOTE
•  The direct control menu screen will disappear if left 
unattended for several seconds.
1
2
3
NOTE
•  Menu options differ in the selected input modes, but the operating procedures are the same.
•  The screens in the operation manual are for explanation purposes (some are enlarged, others cropped) and may vary slightly from the actual screens.
• Items with  4 cannot be selected for various reasons.
 23
LC -4 2X 20E -g b.in dd   2 3LC-42X20E-gb.indd   232007/0 9/0 4   1 6:3 1:2 32007/09/04   16:31:23
 
						

							
Action Mode
This function improves LCD response and moving 
picture quality by reducing motion blur.
Press ACTION  to turn the Action Mode on/off.
•  The Action Mode screen indicates the current on/off status.
•  The Action Mode screen goes out after several seconds.
Film Mode
Automatically detects a film-based source (originally 
encoded at 24/25 frames/second, depending on the 
vertical frequency), analyses it and then recreates each 
still film frame for high-definition picture quality.
Active Contrast
Automatically adjusts the contrast of an image 
according to the scene.
3D-Y/C
Provide high quality images with minimal dot crawl and 
cross colour noise by detecting changes in the image.
Picture Settings
Basic adjustment
Item
Off:  The brightness is fixed at the value set in Backlight.
On:  Automatically adjusts
On:Display:  Displays the OPC effect on the screen while 
adjusting the brightness of the screen.
Automatically adjust the brightness of the screen.
NOTE
•  When set to “On”, the TV senses the surrounding light and  automatically adjusts the backlight brightness. Make sure 
no object obstructs the OPC sensor, which could affect its 
ability to sense surrounding light.
Item
High:  White with bluish tone
Mid-High:  Intermediate tone between High and Middle
Middle:  Natural tone
Mid-Low:  Intermediate tone between Middle and Low
Low:  White with reddish tone
This TV provides various advanced functions for 
optimising the picture quality.
Colour Temp.
Action Mode
Film Mode
Active Contrast
3D-Y/C
Monochrome
Range of OPC High
Mid-High Middle
Mid-Low Low
Colour Temp.
Adjust the colour temperature to give the best white 
image.
Item
Standard:  Normal adjustment
Fast:  
Set the optimum image quality for fast-moving images.Slow:  Set the optimum image quality for slow-moving images.Off: No detecting
NOTE
•  3D-Y/C may not operate depending on the input signal  type or noisy input signal.
•  3D-Y/C has even more effect on composite video signals  (CVBS).
MENU  [Picture ] 
Picture  Audio 
Contrast  OPC [Off]
Brightness 
Colour 
Tint 
Sharpness 
Advanced 
Reset  [+30] 
[0]
[0] 
[0] 
[0] 
0 
–30 
–30 
–30 
–10  +40 
+30 
+30 
+30 
+10 
Backlight [+14] –16 
+16 
DYNAMIC 
Adjust the picture to your preference with the following 
picture settings.
Adjustment items
Selectable items c
 button d button
Backlight The screen dims The screen brightens
Contrast For less contrast For more contrast
Brightness For less brightness For more brightness
Colour For less colour intensity For more colour 
intensity
Tint Skin tones become 
purplish Skin tones become 
greenish
Sharpness For less sharpness For more sharpness
OPC
Picture
Picture adjustments
Picture
Advanced
Picture
 24
LC -4 2X 20E -g b.in dd   2 4LC-42X20E-gb.indd   242007/0 9/0 4   1 6:3 1:2 32007/09/04   16:31:23
 
						

							
Monochrome
For viewing a video in monochrome.
Range of OPC
The brightness level range of the OPC sensor’s 
automatic adjustments can be set according to your 
preferences. The adjustment range of the OPC sensor 
can be set to a maximum of k16 and a minimum of 
l 16.
Selectable 
items Description
Max. l16 through  k16
Min. l16 through  k16
NOTE
•  This function is available only when the “OPC” setting is set 
to “On” or “On: Display”.
•  The maximum setting cannot be set to a smaller number  than the minimum setting.
•  The minimum setting cannot be set to a bigger number  than the maximum setting.
•  The maximum and minimum settings cannot be set to the  same number.
• 
Depending on the brightness of the surrounding light, the OPC 
sensor might not operate if the adjustment range is small.
Audio Settings
You can adjust the sound quality to your preference 
with the following settings.
Selectable 
items c
 button d button
Treble For weaker treble For stronger treble
Bass For weaker bass For stronger bass
Balance Decrease audio from 
the right speaker Decrease audio from 
the left speaker
MENU  [
Audio ]
Audio Power Control
Balance Treble
Surround
Reset [   0]
[   0]
–15
L +15
R
[Off]
Bass[   0] –15
+15
DYNAMIC
This function allows you to enjoy realistic “live” sound.
Power Save Settings
MENU    [
Power Control ]
Power Control
Setup
No Signal Off
No Operation Off
Ecology
Sleep Timer [Disable]
[Disable]
When set to “Enable” the TV will automatically enter the 
standby mode if there is no signal input for 15 minutes.
•  Five minutes before the TV enters standby mode, the 
remaining time displays every minute.
NOTE
•  When a TV programme finishes, this function may not  operate.
Audio adjustment
Audio
Surround
Audio
No Signal Off
Power Control
Basic adjustment
AV Mode
AV Mode gives you five viewing options to choose from 
to best match the system environment, which can vary 
due to factors like room-brightness, type of programme 
watched or the type of image input from external 
equipment.
Press  AV MODE .
Each time you press  AV MODE, the mode 
changes.
•  You can also switch the mode on the “Picture” and 
“Audio” menu screen by pressing  AV MODE.
1
2
Item
STANDARD:  For a highly defined image in a normally 
bright room.
MOVIE:  For viewing a movie in a darkened room.
GAME:  For playing of video games.
PC*:  For PC.
xvYCC**:  Produce realistic colour on the TV screen unlike 
any other signal.
USER:  Allows the user to customise settings as desired. 
You can set the mode for each input source.
DYNAMIC (Fixed):  For a clear-cut image emphasising 
high contrast for sports viewing. (The Picture and Audio 
settings cannot be adjusted.) Each setting value cannot 
be changed in this mode.
DYNAMIC:  For a clear-cut image emphasising high 
contrast for sports viewing.
NOTE
•  The item marked with * is available only when selecting  “EXT4”, “EXT5”, “EXT6” or EXT7” from the INPUT SOURCE 
menu.
•  The item marked with ** is available only when accepting  an xvYCC signal through an HDMI terminal.
 25
LC -4 2X 20E -g b.in dd   2 5LC-42X20E-gb.indd   252007/0 9/0 4   1 6:3 1:2 42007/09/04   16:31:24
 
						

							
The TV will automatically enter the standby mode if no 
operations are performed during the time span you set 
(“30min.” or “3hr.”).
•  Five minutes before the TV enters standby mode, the remaining time displays every minute.
When set to “Yes” the TV activates the following power 
saving mode.
•  OPC set to “On” (Page 24)
•  Standby Mode set to “Mode 2” (Page 32)
•  No Signal Off set to “Enable” (Page 25)
•  No Operation Off set to “3hr.” (Page 26)
Allows you to set a time when the TV automatically 
switches to standby.
NOTE
•  Select “Off” to cancel the sleep timer.
•  When the time has been set, countdown automatically starts.
•  Five minutes before the preset of time expires, the  remaining time displays each minute.
No Operation Off
Power Control
Ecology
Power Control
Sleep Timer
Power Control
Basic adjustment
Channel Settings
Auto Installation
Auto Installation
Setup
The TV automatically detects and stores all available 
services in your area. This function also allows you to 
perform the channel setting for “Digital” and “Analogue” 
individually and reconfigure the settings after the initial 
auto installation has been completed.
After selecting “Yes” on the screen, you can set 
language and channel search the same as in the 
initial auto installation. Follow steps 2, 4 and 5 
on page 9.
NOTE
•  You cannot set the country setting in “Auto Installation” in the Setup menu. If you want to reconfigure the country 
setting, automatically execute initial auto installation after 
executing “Reset” from the Setup menu.
•  The current country setting is displayed on the screen.
1
Digital channel settings
Programme Setup
Setup
Digital Setting
You can reconfigure DTV services settings 
automatically or manually.
E Additional Search
Use this menu to add new services automatically after 
auto installation has been completed.
E Manual Search
Add new services within a specified frequency band.•  Enter the frequency using  0 - 9 numeric buttons.
E Manual Adjust
Configure various settings for each service using the 
Colour (R, G, Y, B)  buttons.
MENU    [
Setup  ... 
Programme Setup  ... 
Digital Setting  ... 
Manual Adjust ] 
DTV 993  Service 
No.  Old
LCN
EPG 
Skip 
CH 
Skip 
Lock 
Service 
Name 
SIT 3 
DTV 994  ✔ ✔ 
SIT 2 
DTV 995  ✔ 
SIT 1 
DTV 996 Monosco 576-2 
DTV 997 Monosco 576-1 
DTV  998  Color Bar 576i 
DTV 999 HD Monosco  : Lock 
R : CH Skip G : EPG Skip Y : Sort B 
Press  a/b  to select the desired service.
Press the colour button on the remote control 
corresponding with the item you want to 
reconfigure.
• The  ✔ mark indicates the operation is set to on. Each 
time the colour button is pressed, you can switch the 
corresponding operation on/off.
1
2
Buttons for Manual Adjust operation
Lock: Press R button . 
When the service is locked, you must enter your PIN 
whenever you tune to the service.
CH Skip: Press G button . 
Services with a  ✔ mark are passed over when 
pressing  Pr /s  in the TV/remote control unit.
EPG Skip: Press Y button . 
Services with a  ✔ mark are passed over in the 
Electronic Programme Guide (EPG).
Sort: Press B button . 
The item position of services can be sorted.
1  Press  a/b  to select the service whose item    
  position you want to move, and then press  OK.
DTV 994  ✔ ✔ 
SIT 2 
DTV 995  ✔ 
SIT 1 
2  Press  a/b  to move it to the desired position,  
  and then press  OK.
DTV 994
✔✔
SIT 1
DTV 995 ✔
SIT 2
3  Repeat steps 1 and 2 until all desired service    
  items are sorted.
 26
L C -4 2X 20E -g b.in dd   2 6LC-42X20E-gb.indd   262007/0 9/0 4   1 6:3 1:2 42007/09/04   16:31:24
 
						

							
Basic adjustment
E Sort
Channel positions can be sorted freely.Press  c/d  to select “Yes”, and then press  OK.
Press  a/b /c /d  to select the channel you 
want to move, and then press  OK.
Press  a/b /c /d  to move it to the desired 
position, and then press  OK.
Repeat steps 3 and 4 until all desired channels 
are sorted.
E Erase Programme
An individual programme can be erased. Press  c/d  to select “Yes”, and then press  OK.
Press  a/b /c /d  to select the channel you 
want to erase, and then press  OK.
•  A message screen pops up.
Press  c/d  to select “Yes”, and then press 
OK  to erase the selected programme. All the 
subsequent programmes move up.
Repeat steps 3 and 4 until all desired channels 
are erased.
1
2
3
4
1
2
3
4
Fine
Colour sys.
Sound sys. (Broadcasting systems) Channels with “Skip” set to “On” are passed over when using 
P
r /P s  even if selected while watching the image from the 
TV.
When connecting a decoder to the unit, you need to select 
EXT1 or EXT2.
NOTE
•  “Off” is factory preset value.
You can block the viewing of any channel.
NOTE
•  See “Child Lock” for setting a PIN.
•  When Lock is set to “On” for a channel, “Child lock has  been activated.” displays, and the image and sound of the 
channel are blocked.
• When pressing  6 while “Child lock has been activated.” 
displays, the PIN input menu will display. Inputting the 
correct PIN lifts the child lock temporarily until the power is 
turned off.
Analogue channel settings
Programme Setup
Setup
Analogue setting
You can reconfigure Analogue TV channels settings 
automatically or manually.
E Additional search
Use this menu to add new channels automatically after 
auto installation has been made.
•  Start searching channels after selecting colour system and  sound system.
E Manual Adjust
Use this menu to set up analogue TV channels 
manually.
  After selecting “Yes” on the screen, press  a/b /
c /d  to select the channel you want to set and 
the press  OK. 
You can adjust the frequency to the desired position.
NOTE
•  Adjust while checking the background picture as a 
reference.
• Instead of pressing  c/d  to adjust the frequency, you 
can set by directly entering the frequency number of the 
channel with  0 - 9.
EXAMPLE
• 179.25 MHz: Press  1 s  7  s 9  s 2  s 5.
• 49.25 MHz: Press  4 s  9  s 2  s 5  s OK .
Select the optimum colour system to receive. (Auto,
PAL, SECAM)
Select the optimum sound systems (Broadcasting systems) 
to receive. (B/G, D/K, I, L/L’)
Skip
Decoder
Lock
When a TV channel sends its Network Name, the Auto 
Installation detects the information and assigns a name 
to it. However, you can change individual channel names.
Press  a/b /c /d  to select each character of 
the new name for the channel, and then press 
OK .
Repeat step 1 above until the name is fully spelt 
out.
NOTE
•  The name can be 5 characters or less.
•  If a channel name is less than 5 characters, select “END” to  set the channel name.
1
2
Label
 27
LC -4 2X 20E -g b.in dd   2 7LC-42X20E-gb.indd   272007/0 9/0 4   1 6:3 1:2 42007/09/04   16:31:24
 
						

							
Basic adjustment
Password/Parental lock settings
Child Lock
Setup
Allows you to use a PIN to protect certain settings from 
being accidentally changed.
Change PIN
Register a 4-digit password number to use the Child 
Lock function.Enter the 4-digit number as a PIN using  0 –  9.
Enter the same 4-digit number as in step 1 to 
confirm.
•  “The system PIN has been changed successfully”  displays.
NOTE
•  To view a locked channel, you must enter the PIN. (See  pages 26 and 27 for locking channels from viewing in 
analogue TV and DTV mode.) When you select a locked 
channel, a PIN prompt message pops up. Press  6 to 
display the PIN input window.
Cancel PIN
Allows you to reset your PIN.
NOTE
•  As a precautionary measure, make a note of your PIN 
on the back of this operation manual, cut it out and 
keep it in a safe place that children cannot reach.
Parental rating
This function allows DTV services to be restricted. 
It prevents children from watching violent or sexual 
scenes that may be harmful.
NOTE
•  “Universal viewing” and “Parental approval pref.” are ratings 
used exclusively in France.
•  Refer to page 40 for details about ratings.
1
2
Language
Setup
You can select a OSD language from the Setup 
menu. Select from among 22 languages. (Czech, 
Danish, Dutch, English, Estonian, Finnish, French, 
German, Greek, Hungarian, Italian, Latvian, Lithuanian, 
Norwegian, Polish, Portuguese, Russian, Slovak, 
Slovene, Spanish, Swedish, Turkish)
Language Settings (language, 
subtitle, multi audio)
Subtitle
Digital Setup
Set up to 2 preferred subtitle languages (including 
subtitles for the hearing impaired) to display if subtitles 
are available.
NOTE
•  Subtitles will not be displayed when the service does not  contain subtitle information.
Digital Audio Language
Option
Set up to 3 preferred multi audio languages to display if 
the audio languages are available.
E Switching the multi audio languages
Each time you press  2 on the remote control, the 
audio language switches.
Key Lock
Option
This function allows you to lock the buttons on the 
TV or remote control in order to prohibit children from 
changing the channel or volume.
Item
Off:  Unlock the buttons.
RC Control Lock:  Lock all buttons on the remote control.
Button Control Lock:  Lock the buttons except the power 
switch on the TV.
NOTE
•  You cannot set both “RC Control Lock” and “Button  Control Lock” at the same time.
Selectable items
E 1st language E 2nd language
E For hearing impaired
E Switching subtitle languages
E Cancelling the lock
Press the  MENU button on the TV and set to “Off” to 
cancel the “RC Control Lock”. Press the  MENU button 
on the remote control and set to “Off” to cancel the 
“Button Control Lock”.
•  Refer to page 23 for menu operation using  MENU button 
on the TV.
Each time you press [ on the remote control, the 
subtitle switches.
Set “For hearing impaired” to “Yes”
(For hearing impaired) 1st Language 2nd Language
Off
••••••••
Set “For hearing impaired” to “No”
1st Language 2nd Language
(For hearing impaired)
Off
••••
 28
L
C -4 2X 20E -g b.in dd   2 8LC-42X20E-gb.indd   282007/0 9/0 4   1 6:3 1:2 52007/09/04   16:31:25