Sharp Lc 37ga3e Operation Manual
Have a look at the manual Sharp Lc 37ga3e Operation Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 615 Sharp manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
49 Useful features Teletext function What is Teletext? Teletext broadcasts pages of information and entertainment to specially equipped television sets. Your TV receives Teletext signals broadcast by a TV network, and decodes them into graphical format for viewing. News, weather and sports information, stock exchange prices and programme previews are among the many services available. Teletext mode Teletext is turned on/off with m on the remote control unit. You can operate your TV in Teletext mode directly by inputting commands with the remote control unit. Turning on and off Teletext Select a TV channel or external input source providing the Teletext programme. Press m to display the Teletext. Press m again to display the Teletext on the right screen and normal image on the left screen. • Each time you press m, the screen switches as shown upper right. • If you select a programme with no Teletext signal, “No Teletext available.” displays. • The same message displays during dual screen or other modes if no Teletext signal is available. 1 TELETEXT TELETEXT 2 3 REDGREEN YELLOW BLUE TELETEXT When viewing the Teletext information • Press Pr to increase the page number. • Press Ps to decrease the page number. Button functions Colour (RED/GREEN/YELLOW/BLUE): You can select a group or block of pages displayed in the coloured brackets at the bottom of the screen by pressing the corresponding Colour (RED/GREEN/ YELLOW/BLUE) on the remote control unit. Upper half Lower halfFull 0 – 9: Directly select any page from 100 to 899 by using 0 – 9. f: Each time you press f, the TELETEXT image switches as shown below. k: To reveal hidden information such as an answer to a quiz, press k. • Press k again to hide the information. d: To stop updating Teletext pages automatically, press d. • Press d again to release the hold mode. LC-37GA3E(E)-j04.6.25, 8:06 AM 49
50 Useful features TOP Overview screen BLOCK PAGES TV PROGRAMS COLOR BAR WEATHER NEWS MOVIE LOCAL SPORTS BLOCK 1 BLOCK 2 BLOCK 3GROUP PAGES FOOT BALL BASKETBALL TENNIS SKI JUDO SWIM GROUP 1 GROUP 2 GROUP 3 GROUP 4 INDEX Displaying Subtitle You can display several subtitles as they are transmitted. Press [ to display the subtitle. • Subtitle is updated by the information sent by the broadcasting station. • To stop updating Subtitle automatically, press d. 1 2Press [ to exit the subtitle screen. Displaying TOP Overview When receiving TOP Teletext, you can read a TOP text overview. Press m to display Teletext. Press l to display the TOP Overview as shown below. 1 2 3Select the desired block or group by using a/b/c/d. Press OK to display the selected block or group pages. Press l to exit the TOP Overview screen. 4 5 NOTE • Subtitle will not be displayed when the service does not contain the subtitle information. Time display You can display the time information included in the Teletext broadcasts. Select a TV channel providing Teletext information. (The time information is automatically captured.) 1 2 3 4 Press p. The channel display will appear on the Display. Press p again within the three-second interval the channel display is on the screen. Time information will display on the lower left of the screen for about three seconds. Even when you change the TV channel, you can display the time information with steps 2 – 3 above. NOTE • The time display cannot be stored once the power is turned off. When you turn on the power, perform steps 1 – 4 again. • If acquired successfully, the time information will appear in the upper-right corner of the screen by pressing MENU. LC-37GA3E(E)-j04.6.25, 8:06 AM 50
25 Language setting for on-screen display You can also select a language from setup menu. Select from among 13 languages. 3 Press MENU and the MENU screen displays.1 2 4 Press c/d to select “Setup”. Press a/b to select “Language”, and then press OK. Press a/b/c/d to select the desired language listed on the screen, and then press OK. OPC setting Automatically adjusts the brightness of the screen. Press c/d to select “Picture”. 2 Using OPC on the menu screen Press MENU and the MENU screen displays. 1 Press a/b to select “OPC”. Press c/d to select “On”.3 4 Description The brightness is fixed at the value set in “Backlight” (see page 26). Automatically adjusts Selected item Off On NOTE • When set to “On”, the System senses the surrounding light and automatically adjusts the backlight brightness. Make sure no object obstructs the OPC sensor, which could affect its ability to sense surrounding light. Using OPC on the remote control unit Press OPC to switch the Optical Picture Control on and off. Language list Basic adjustment settings Dutch English Finnish French German Greek ItalianPolish Portuguese Russian Spanish Swedish Turkish LC-37GA3E(E)-e04.6.25, 7:57 AM 25 Audio adjustment You can adjust the sound quality to your preference with the following settings. Press c/d to select “Audio”. Press a/b to select a specific adjustment item. Press c/d to adjust the item to your desired position. Basic adjustment settings 2 3 4 cbutton For weaker treble For weaker bass Decrease audio from the right speaker Selected item Treble Bass Balancedbutton For stronger treble For stronger bass Decrease audio from the left speaker Press MENU and the MENU screen displays.1 NOTE • For resetting all adjustment items to factory preset values, press a/b to select “Reset”, press OK, press c/d to select “Yes”, and then press OK. • Audio menu items are greyed out when Audio output is variable or when headphones are in use. • Balance is greyed out when Dolby Virtual is set to “On”. Press c/d to select “Audio”.2 Press MENU and the MENU screen displays.1 Press c/d to select “On”, and then press OK.4 3Press a/b to select “Dolby Virtual”, and then press OK. NOTE • You can choose Dolby Virtual by pressing Virtual on the remote control unit. See page 17 for Dolby Virtual. • Audio menu items are greyed out when Audio output is variable or when headphones are in use. • External Audio Bypass is greyed out when Dolby Virtual is set to “On”. • Balance is greyed out when Dolby Virtual is set to “On”. • For some discs, setup may be required on your DVD. In this case, please refer to the operation manual of your DVD player. • You may not get the Dolby Virtual Surround effect if you adjust “Treble” or “Bass” setting. Dolby Virtual You can also produce Dolby Virtual effects from the “Audio” setting. MENU [ Audio] AudioPower Control Treble Bass Balance Dolby Virtual Reset[Off] [0] [0]–15 L+15 [0] –15+15 R USER [TV] LC-37GA3E(E)-f04.6.25, 7:59 AM 29 CAUTION ¥ To protect all equipment, always turn off the TV before connecting to a decoder, VCR, DVD player, PC, game console, camcorder or other external equipment. NOTE ¥ See pages 32 to 35 for external equipment connection. ¥ Please refer to the relevant operation manual (DVD player, PC, etc.) carefully before making connections. ¥ Each time is pressed, the input source toggles. ¥ If the image does not come in clearly, you may need to change the input signal type setting on the ÒInput SelectÓ menu. ¥ Refer to your external equipment operation manual for the signal type. Displaying an external equipment image Explanation here is for the setting when connecting DVD to INPUT3 terminal. Displaying a DVD image (Example) To watch a DVD image, select ÒINPUT3Ó from ÒINPUT SOURCEÓ menu using on the remote control unit or INPUT on the Display. Select the desired signal type on ÒInput SelectÓ in the ÒOptionÓ menu. (See page 38.) The setting is stored and can be selected on the ÒINPUT SOURCEÓ menu. INPUT SOURCE TV INPUT1 INPUT2 INPUT3 INPUT5 INPUT4 1 MENU [ Option ... Input Select] COMPONENT Y/C CVBS RGB 2 You can connect many types of external equipment to your TV, like a decoder, VCR, DVD player, PC, game console and camcorder. To view external source images, select the input source from on the remote control unit or INPUT on the Display. For INPUT3 signal LC-37GA3E(E)-g04.6.25, 8:00 AM 31 1 2 Image position (for TV/AV input mode) For adjusting a pictur position. PrMENU and the MENU scr Prc/d to select
52 Appendix PC compatibility chart Apple and Macintosh are registered trademarks of Apple Computer, Inc. DDC is a registered trademark of Video Electronics Standards Association. Power Management is a registered trademark of Sun Microsystems, Inc. VGA and XGA are registered trademarks of International Business Machines Co., Inc. PC/MAC ResolutionHorizontal FrequencyVertical FrequencyVESA Standard PC 31.5 kHz 37.9 kHz 31.5 kHz 37.9 kHz 31.5 kHz 37.9 kHz 37.5 kHz 43.3 kHz 31.5 kHz 35.1 kHz 37.9 kHz 48.1 kHz 46.9 kHz 53.7 kHz 48.4 kHz 56.5 kHz 60.0 kHz 68.7 kHz 45.0 kHz 48.1 kHz 48.4 kHz 64.0 kHz 34.9 kHz 49.7 kHz 60.2 kHz640 x 400 720 x 400 VGA 640 x 480 WVGA 848 x 480 SVGA 800 x 600 1024 x 768 XGA 1280 x 720 WXGA1280 x 768 SXGA1280 x 1024 VGA 640 x 480 MAC13 XGA 1024 x 768 MAC19SVGA 832 x 624 MAC1660 Hz 85 Hz 60 Hz 85 Hz 60 Hz 72 Hz 75 Hz 85 Hz 60 Hz 56 Hz 60 Hz 72 Hz 75 Hz 85 Hz 60 Hz 70 Hz 75 Hz 85 Hz 60 Hz 60 Hz 60 Hz 60 Hz 67 Hz 75 Hz 75 HzO O O O O O O O O O O O O O O O 1366 x 768 LC-37GA3E(E)-k04.6.25, 8:07 AM 52
53 RS-232C port specifications Return code Command 4-digits Parameter 4-digits PC Control of the System • When a program is set, the display can be controlled from the PC using the RS-232C terminal. The input signal (PC/video) can be selected, the volume can be adjusted and various other adjustments and settings can be made, enabling automatic programmed playing. • Attach an RS-232C cable cross-type (commercially available) to the supplied Din/D-sub RS-232C for the connections. NOTE • This operation system should be used by a person who is accustomed to using PCs. Communication conditions Set the RS-232C communications settings on the PC to match the display’s communications conditions. The displays communications settings are as follows: Baud rate: Parity bit: Data length: Stop bit: Flow control:9,600 bps 8 bits None 1 bit None Appendix Command format Communication procedure Send the control commands from the PC via the RS-232C connector. The Display operates according to the received command and sends a response message to the PC. Do not send multiple commands at the same time. Wait until the PC receives the OK response before sending the next command. Eight ASCII codes e CR Command 4-digits: Command. The text of four characters. Parameter 4-digits: Parameter 0 – 9, x, blank, ? Parameter Input the parameter values, aligning left, and fill with blank(s) for the remainder. (Be sure that four values are input for the parameter.) When the input parameter is not within an adjustable range, “ERR” returns. (Refer to “Response code format”.) When “?” is input for some commands, the present setting value responds. C1 C2 C3 C4 P1 P2 P3 P4 0055 100 –30 0009 0 ???? ? LC-37GA3E(E)-k04.6.25, 8:07 AM 53
54 Commands P I I I D C C I I I I I I I I I I I I I I I A A A A A A VPOWER OFF (STANDBY) INPUT SWITCHING (TOGGLE) TV (CHANNEL FIXED) INPUT1 – 5 (1 – 5) TV DIRECT CHANNEL (1 – 99) CHANNEL UP CHANNEL DOWN INPUT1 (CVBS) INPUT1 (RGB) INPUT2 (CVBS) INPUT2 (Y/C) INPUT3 (CVBS) INPUT3 (Y/C) INPUT3 (RGB) INPUT3 (COMPONENT) INPUT4 (AUTO) INPUT4 (S-VIDEO) INPUT4 (VIDEO) DIGITAL PC ANALOGUE PC DIGITAL AV ANALOGUE AV TOGGLE STANDARD MOVIE GAME USER DYNAMIC VOLUME (0 – 60) POWER SETTING INPUT SELECTION A CHANNEL INPUT SELECTION B AV MODE SELECTION VOLUMEO T T A C H H N N N N N N N N N N N N N N N V V V V V V OW G V V C U D P P P P P P P P P P P P P P P M M M M M M LR D D D H P W 1 1 2 2 3 3 3 3 4 4 4 5 5 5 5 D D D D D D M0 _ _ * * _ _ 0 1 0 1 0 1 2 3 0 1 2 0 1 2 3 0 1 2 3 4 5 *_ _ _ _ * _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ *_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ __ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ CONTROL ITEM COMMAND PARAMETERCONTROL CONTENTS H H V V C P W W W W W W W W W W W M M M A A A T T A O O O O O O T T DH-POSITION (AV) (10 – 10) H-POSITION (PC) (0 – 180) V-POSITION (AV) (20 – 20) V-POSITION (PC) (0 – 100) CLOCK (0 – 180) PHASE (0 – 40) TOGGLE (AV) NORMAL (AV) ZOOM 14:9 (AV) PANORAMA (AV) FULL (AV) CINEMA 16:9 (AV) CINEMA 14:9 (AV) NORMAL (PC) CINEMA (PC) FULL (PC) DOT BY DOT (PC) TOGGLE MUTE MUTE OFF TOGGLE ON OFF DUAL SCREEN OFF DUAL SCREEN ON TOGGLE OFF SLEEP TIMER 30 MIN SLEEP TIMER 1 HOUR SLEEP TIMER 1 HOUR 30 MIN SLEEP TIMER 2 HOUR SLEEP TIMER 2 HOUR 30 MIN TEXT OFF TEXT ON (TOGGLE) DIRECT PAGE JUMP (100 – 899) WIDE MODE POSITION DOLBY VIRTUAL MUTE DUAL SCREEN AUDIO CHANGE SLEEP TIMER TEXTP P P P L H I I I I I I I I I I I U U U C C C W W C F F F F F F E E CO O O O C S D D D D D D D D D D D T T T D D D I I H T T T T T T X X PS S S S K E E E E E E E E E E E E E E E V V V N N A M M M M M M T T G* * * * * * 0 1 2 3 4 5 6 7 8 9 1 0 1 2 0 1 2 0 1 _ 0 1 2 3 4 5 0 1 ** * * * * * _ _ _ _ _ _ _ _ _ _ 0 _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ ** * * * * * _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ *_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ CONTROL ITEM COMMAND PARAMETERCONTROL CONTENTS Appendix NOTE •If an underbar (_) appears in the parameter column, enter a space. •If an asterisk (*) appears, enter a value in the range indicated in brackets under CONTROL CONTENTS.Return code (0DH) Response code format Normal response Problem response (communication error or incorrect command) Return code (0DH) OK ERR LC-37GA3E(E)-k04.6.25, 8:07 AM 54
55 Appendix SCART (INPUT 1) 1. Audio right output (TV Monitor out) 2. Audio right input 3. Audio left output (TV Monitor out) 4. Common earth for audio 5. Earth for blue 6. Audio left input 7. Blue input8. Audio-video control 9. Earth for green 10. Not used 11. Green input 12. Not used 13. Earth for red 14. Not used15. Red input 16. Red/Green/Blue control 17. Earth for video 18. Earth for Red/Green/Blue control 19. Video output (TV Monitor out) 20. Video input 21. Plug shield SCART (INPUT 2) 1. Audio right output 2. Audio right input 3. Audio left output 4. Common earth for audio 5. Earth 6. Audio left input 7. Not used8. Audio-video control 9. Earth 10. AV LINK control 11. Not used 12. Not used 13. Earth 14. Not used15. Chroma S-Video input 16. Not used 17. Earth for video 18. Earth 19. TV Monitor output 20. Video input/S-video input 21. Plug shield 13579111315171921 2468101214161820 Connecting pin assignments for SCART Various audio and video devices may be connected via the SCART terminals. SCART (INPUT 3) 1. Audio right output 2. Audio right input 3. Audio left output 4. Common earth for audio 5. Earth 6. Audio left input 7. Blue input8. Audio-video control 9. Earth 10. Not used 11. Green input 12. Not used 13. Earth 14. Not used15. Red input/Chroma S-Video input 16. Red/Green/Blue control 17. Earth for video 18. Earth 19. TV Monitor output 20. Video input/S-video input 21. Plug shield LC-37GA3E(E)-k04.6.25, 8:07 AM 55
56 Appendix Item37o LCD COLOUR TV, Model: LC-37GA3E Video Colour System PAL/SECAM/NTSC 3.58/NTSC 4.43/PAL 60 TV FunctionB/G, I, D/K, L, L’ TV-Standard (CCIR) Specifications LCD panel37o Advanced Super View & BLACK TFT LCD Number of dots 3,147,264 dots (1366 g 768 g 3 dots) •As a part of policy of continuous improvement, SHARP reserves the right to make design and specification changes for product improvement without prior notice. The performance specification figures indicated are nominal values of production units. There may be some deviations from these values in individual units. VHF/UHFE2–E69ch, F2–F10ch, I21–I69ch, IR A–IR Jch CATV Hyper-band, S1–S41ch TV-Tuning System Auto Preset 99 ch, Auto Label, Auto Sort STEREO/BILINGUAL NICAM/A2 Receiving Channel Brightness 450 cd/m 2 Backlight life 60,000 hours (at Backlight Standard position) Viewing angles H : 170° V : 170° Audio amplifier 10W g 2 SpeakersØ 8 cm 2pcs, Ø 2.5 cm 2pcs Terminals SCART (AV input, RGB input, TV output) INPUT 2 INPUT 3SCART (AV input/output, Y/C input, RGB input), RCA pin (Component input) Rear INPUT 1 UHF/VHF 75 q Din type SCART (AV input/output, Y/C input, AV Link)ANTENNA IN INPUT 4 S-VIDEO (Y/C input), RCA pin (AV input) Optional accessory The listed optional accessories are available for the LCD colour TV. Please purchase them at your nearest shop. •Additional optional accessories may be available in near future. When purchasing, please read the newest catalogue for compatibility and check the availability.No. Wall mount bracketPart name Part number 1 AN-37AG2 Front AUDIO OUTPUTRCA pin (Variable/Fixed), switchable with INPUT 4 DC OUTPUTDC 9V 7W MAX SPEAKERExternal speaker output terminal (L and R) OSD languageEnglish/German/French/Italian/Spanish/Dutch/Swedish/Portuguese/Finnish/Turkish/Greek/ Russian/Polish Power Requirement AC 220–240 V, 50 Hz Power Consumption 181 W (3 W Standby) (Method IEC60107) Weight Accessories Operation manual, Remote control unit (g1), AC cord (g1), “AAA” size battery (g2) HeadphonesØ 3.5mm jack (Audio output) 18.3 kg (Display only), 22 kg (with Display and speaker), 26.6 kg (with Display, speaker and stand) CENTRE CHANNEL INPUTRCA pin RS-232C D-sub 9pin male connector INPUT 5Ø 3.5 mm jack (Audio input), DVI-I (DVI-I input) LC-37GA3E(E)-k04.6.25, 8:07 AM 56
57 Dimensional drawings 917 706 548 645 434 434 822.6 463.8 200 20095.9 100 677 102 307 115 Unit: mm LC-37GA3E(E)-k04.6.25, 8:07 AM 57
58 Information for Customers on environmentally friendly disposal of this SHARP product If this product cannot be used any more, it should be disposed of in a legally correct and environmentally sound way. DO NOT DISPOSE OF THIS PRODUCT WITH YOUR HOUSEHOLD WASTE OR MIXED WITH OTHER WASTES! YOU MIGHT ENDANGER THE ENVIRONMENT! Sharp Corporation is committed to protecting the environment and conserving energy. Our goal is to minimize the environmental impact of our products by continually implementing and improving product technologies, designs, and customer information aimed at environmental conservation. (1) For our customers in Belgium, The Netherlands, Sweden, and Switzerland SHARP takes part in the respective national recycling systems for electronic equipment, which have been founded on the base of the environmental laws in these countries. Please see here details on the respective countries. Country Recycling Information for that Country Sweden The Netherlands Belgium SwitzerlandPlease use the Swedish electronics recycling system called “ELRETUR”, and see the website at http://www.el-kretsen.se Please use the Dutch electronics recycling system called “ICT-Milieu”, and see the website at http://www.nederlandict.nl/index.php Please use the Belgian electronics recycling system called “Recupel”, and see the website at http://www.recupel.be Please use the Swiss electronics recycling system called “SWICO”, and see the website at http://www.swico.ch (2) For our customers in United Kingdom, Germany, France, and Italy Please contact your local authorities for collection and recycling facilities, or contact a recycling service company, which is licensed for the recycling of electronic equipment. HOW TO SET THE FACTORY PRESETS Turn off the TV by pressing POWER. Press and hold down RESET and press POWER on the TV to turn it on. All setting items (except TV channel) return to the factory presetting. You can run the Auto Installation again by using the following steps. 1Turn on the power of the TV. 2Press MENU. (Make sure the menu screen displays.) 3Press c/d to select “Setup”. 4Press a/b to select “Auto Installation”, and then press OK. 5Press c/d to select “Ye s”, and then press OK. NOTE •As a precautionary measure, make a note of your PIN above, scissor it from this manual, and keep it in a familiar place. The PIN is . LC-37GA3E(E)-k04.6.25, 8:08 AM 58