Sharp Lc 32le705 Operation Manual

							39
RS-232C port specifications
PC control of the TVWhen a programme is set, the TV can be controlled 
from the PC using the RS-232C terminal. The input 
signal (PC/video) can be selected, the volume can be 
adjusted and various other adjustments and settings 
can be made, enabling automatic programmed 
playing.
Use an RS-232C serial control cable (cross type) 
(commercially available) for the connections.
NOTEThis operation system should be used by a person 
who is accustomed to using PCs.
RS-232C serial control cable (cross type)
Communication conditionsSet the RS-232C communications settings on the PC 
to match the TV’s communications conditions. The TV’s 
communications settings are as follows:
Baud rate9,600 bps
Data length 8 bits
Parity bit None
Stop bit 1 bit
Flow control None
Communication procedureSend the control commands from the PC via the RS-
232C connector.
The TV operates according to the received command 
and sends a response message to the PC.
Do not send multiple commands at the same time. Wait 
until the PC receives the OK response before sending the 
next command.
Make sure to send “A” with the carriage return and 
confirm that “ERR” returns before operating. •
•
•
Command format
Eight ASCII codes +CR

C1 C2 C3 C4 P1  P2  P3  P4
Command four digits: Command. The text of four 
characters.
Parameter four digits: Parameter 0_9, blank, ?, 
minus
Return code (0DH): ?
ParameterInput the parameter values, aligning left, and fill with 
blank(s) for the remainder (be sure that four values are 
input for the parameter).
When the input parameter is not within an adjustable 
range, “ERR” returns (refer to “Response code format”).
0055 100
0009
0
When “?” is input for some commands, the present 
setting value responds.
????
Response code format
Normal response
OK
Return code (0DH)
Problem response (communication error or incorrect 
command)
ERR
Return code (0DH)



Connecting a PC
LC-LE705E_GB.indd   39 LC-LE705E_GB.indd   39 2009/10/09   14:13:21
2009/10/09   14:13:21
 
						

							40
RS-232C command list
CONTROL ITEM COMMAND PARAMETER CONTROL CONTENTS
POWER 
SETTINGP O W R 0 _ _ _ POWER OFF (STANDBY)
INPUT 
SELECTION A I TGD____
INPUT SWITCHING 
(TOGGLE)
I TVD____TV  (CHANNEL FIXED)
IDTV____ DTV (CHANNEL FIXED)
IAVD*___ EXT 1_4, 9 (1_4, 9), 
HDMI 1_4 (5_8)
CHANNEL D C C H * * _ _ TV DIRECT CHANNEL  (1_99)
CHUP____ CHANNEL UP
CHDW____ CHANNEL DOWN
D T V D * * * _ THREE DIGIT DIRECT  CHANNEL (1_999) (Non-
Nordic countries)
DTVD**** FOUR DIGIT DIRECT 
CHANNEL (1_9999) 
(Nordic countries only)
DTUP____ DTV CHANNEL UP
DTDW____ DTV CHANNEL DOWN
INPUT 
SELECTION B I N P 1 0 _ _ _ EXT 1 (Y/C)
I N P 1 1 _ _ _ EXT 1 (CVBS)
I N P 1 2 _ _ _ EXT 1 (RGB)
I N P 2 0 _ _ _ EXT 2 (Y/C)
I N P 2 1 _ _ _ EXT 2 (CVBS)
AV MODE 
SELECTION A V M D 0 _ _ _ TOGGLE
A V M D 1 _ _ _ STANDARD
A V M D 2 _ _ _ MOVIE
A V M D 3 _ _ _ GAME
A V M D 4 _ _ _ USER
A V M D 5 _ _ _ DYNAMIC (Fixed)
A V M D 6 _ _ _ DYNAMIC
AVMD7___PC
A V M D 1 0 0 _ AUTO
AVMD????
1_7, 100
VOLUME V O L M * * _ _ VOLUME (0_60)
CONTROL ITEM COMMAND PARAMETER CONTROL CONTENTS
POSITION H P O S * * * _ H-POSITION (AV/PC)
V P O S * * * _ V-POSITION (AV/PC)
CLCK * * * _ CLOCK (0_180)
PHS E * * _ _ PHASE (0_40)
WIDE MODE W I D E 0 _ _ _ TOGGLE (AV)
W I D E 1 _ _ _ NORMAL (AV)
W I D E 2 _ _ _ ZOOM 14:9 (AV)
W I D E 3 _ _ _ PANORAMA (AV)
W I D E 4 _ _ _ FULL (AV)
W I D E 5 _ _ _ CINEMA 16:9 (AV)
W I D E 6 _ _ _ CINEMA 14:9 (AV)
W I D E 7 _ _ _ NORMAL (PC)
W I D E 8 _ _ _ CINEMA (PC)
W I D E 9 _ _ _ FULL (PC)
W I D E 1 0 _ _ DOT by DOT (AV/PC)
W I D E 1 1 _ _ UNDERSCAN (AV)
MUTE M U T E 0 _ _ _ TOGGLE
M U T E 1 _ _ _ MUTE
M U T E 2 _ _ _ MUTE OFF
SURROUND A C S U 0 _ _ _ SURROUND TOGGLE
A C S U 1 _ _ _ SURROUND ON
A C S U 2 _ _ _ SURROUND OFF
AUDIO 
CHANGE ACHA____
TOGGLE
SLEEP TIMER O F T M 0 _ _ _ OFF O F T M 1 _ _ _ SLEEP TIMER 30 MIN
O F T M 2 _ _ _ SLEEP TIMER 1 HOUR
O F T M 3 _ _ _ SLEEP TIMER 1 HOUR  30 MIN
O F T M 4 _ _ _ SLEEP TIMER 2 HOUR
O F T M 5 _ _ _ SLEEP TIMER 2 HOUR  30 MIN
TEXT T E X T 0 _ _ _ TEXT OFF
T E X T 1 _ _ _ TEXT ON (TOGGLE)
DCPG***_
DIRECT PAGE JUMP 
(100_899)
Connecting a PC
LC-LE705E_GB.indd   40 LC-LE705E_GB.indd   40 2009/10/09   14:13:22
2009/10/09   14:13:22
 
						

							41
Troubleshooting
ProblemPossible solution
No power.
•
Turn on (;) the MAIN POWER switch on the left side of the TV (Page 4).
Check if you pressed B on the remote control unit. If the indicator on the TV lights up red, press 
B.
Is the AC cord disconnected?
Check if you pressed a on the TV.
•
•
•
•
The TV cannot be operated.
• External influences such as lightning, static electricity, etc., may cause improper operation. In this 
case, operate the TV after first turning off the power, or unplugging the AC cord and re-plugging it in 
after one or two minutes.
•
Remote control unit does not operate.
•
Are batteries inserted with polarity (e, f) aligned?
Are batteries worn out? (Replace with new batteries.)
Are you using it under strong or fluorescent lighting?
Is a fluorescent light illuminating to the remote control sensor?
•
•
•
•
Picture is cut off.
• Is the image position correct?
Are screen mode adjustments (WIDE MODE) such as picture size made correctly? (Pages 31 and 37)
•
•
Strange colour, light colour, or dark 
colour, or colour misalignment.
•
Adjust the picture tone.
Is the room too bright? The picture may look dark in a room that is too bright.
Check the “Colour system” setting (Pages 29 and 34).
•
•
•
Power is suddenly turned off.
• The TV’s internal temperature has increased. Remove any objects blocking the vent or clean.
Is the “Sleep timer” set? Select “Off” from the “Sleep timer” menu (Page 26).
Is “No signal off” or “No operation off” activated? (Page 26)
•
•
•
No picture.
•
Are connections to external equipment correct? (Pages 16_18)
Is the input signal type selected correctly after connection? (Page 34)
Is the correct input source selected? (Page 12)
Is a non-compatible signal being input? (Page 38)
Is the picture adjustment correct? (Pages 23_24)
Is the antenna connected properly? (Page 8)
Is “On” selected in “Audio only”? (Page 25)
•
•
•
•
•
•
•
No sound.
• Is the volume too low?
Make sure that headphones are not connected.
Check if you pressed e on the remote control unit.
Is the proper item selected in the “PC audio select” menu when connecting d\
evices to the HDMI 2 
terminal or the EXT 4 terminal? (Pages 16 and 25)
•
•
•
•
The TV sometimes makes a cracking 
sound.
•
This is not a malfunction. This happens when the cabinet slightly expand\
s and contracts according to 
changes in temperature. This does not affect the TV’s performance.
•
Cautions regarding use in high and low temperature environmentsWhen the TV is used in a low temperature space (e.g., room, office), the picture may leave trails or appear slightly delayed. This is not 
a malfunction, and the TV will recover when the temperature returns to normal.
Do not leave the TV in a hot or cold location. Also, do not leave the TV\
 in a location exposed to direct sunlight or near a heater, as this 
may cause the cabinet to deform and the LCD panel to malfunction.
Storage temperature: e 5 °C to e 35 °C.
•
•
CLEARING THE PIN
Go to “MENU” > “Setup”.
Press a/b to select “Auto installation”, “Programme setup”, “Child lock” or “Reset”, and then press 
;. The PIN input window will display.
Press and hold both :r and i+ on the TV simultaneously until the message appears on the 
screen.
1
2
3
Appendix
LC-LE705E_GB.indd   41 LC-LE705E_GB.indd   41
2009/10/09   14:13:24
2009/10/09   14:13:24
 
						

							42
Updating your TV via DVB-T
Ensure that your TV software version is always up to 
date. From time to time SHARP will make updated TV 
base software and DVB software available.
Digital setup
Download setup
Searching for updates*
All countries except UK, Sweden and Italy are set to “No” for 
this function.
The TV automatically determines whether a new software 
version is available when the TV is in standby mode.
Item
Ye s Automatically searches for new software 
updates available when the TV is in 
standby mode.
No Does not search for update information.
Now Checks if there is new software 
immediately.
Downloading the software
You can select the method of update.
If the software is updated, the confirmation 
message “New download information has 
been detected.” appears.
If the TV receives the update service while in standby 
mode, a confirmation message displays after turning on 
the power.
Follow the screen prompts.
Item
Ye s Starts downloading immediately. It takes 
approximately one hour to update. You 
cannot carry out other operations while 
downloading.
Cancels the download by pressing 
; on the remote control unit when 
“Discontinue” is displayed on the screen 
during the update.
•
No
Starts downloading automatically several 
minutes after entering standby mode.
NOTEThe TV must remain in standby mode for download. Do not 
turn off the power using a on the TV.
Updating the software may take some time.
*
1
•
2
•
•
Information
Message list
When new software is detected, you can confirm the 
update information and download the software from 
“Message list”.
NOTEWhen the TV succeeds at downloading new software, the 
message is updated in the “Message list” of the “Information”\
 
menu.
The software update will not be carried out if there is no new 
software available at the specified download time.
Information
Receiver report
Display reports regarding failures and changes for timer 
settings.
Reset
If complex adjustments are made so that the settings 
cannot be restored to normal, you can reset the settings 
to the factory preset values.
Setup
Reset
Go to “MENU” > “Setup” > “Reset”.
Press c/d to select “Yes”, and then press 
;.
“Now, TV will restart automatically, OK?” displays on the 
screen.
Press c/d to select “Yes”, and then press 
;.
“Now initialising...” displays on the screen and blinks.
After the reset has completed, the power shuts off and 
then comes back on. The screen will have returned to its 
original settings.
NOTEPIN input is required when executing “Reset”. The default 
PIN is “1234”. To change the PIN setting, refer to Password/
Parental lock settings (Page 30). To clear the PIN setting (PIN 
input will no longer be needed), refer to CLEARING THE PIN 
(Page 41).
Identification
Setup
Identification
You can check the TV ID on the screen for reporting to 
customer service.
•
•
1
2
•
3
•
•
•
Appendix
LC-LE705E_GB.indd   42 LC-LE705E_GB.indd   42 2009/10/09   14:13:24
2009/10/09   14:13:24
 
						

							43
Appendix
Updating your TV via USB
Setup
Software update
This function allows you to update to the latest software 
using a USB device. You must update the software 
through the USB terminal.
To check the software version for the TV, use the URL shown 
on the back cover.
CAUTIONThis function is available only for the 705 model series.
Go to “MENU” > “Setup” > “Software 
update”.
Press ; and then insert the USB device 
containing the software update file.
CAUTIONBe sure to insert the USB device correctly into the terminal.
•
•
1
2
•
The TV displays a confirmation screen while 
checking the data in the inserted USB device.
CAUTIONIf the data is not compatible with the system, an error message 
appears on the screen. Repeat steps 2 and 3 after pressing 
;.
When an error message displays, check to see if:
The USB device is inserted firmly.
The USB memory has two or more software update files.
No data for updating the system exists in the USB 
memory.
The software update file is broken.
The software update file is not compatible with your TV’s 
software.
The current system is same as the system update data.
The TV displays the software version 
information after checking the data.
Press c/d to select “Yes” to update the 
system, and then press ;.
Press ; to automatically reset and start the 
update operation.
This operation may take a while.
The TV starts updating the system
A confirmation message appears on the 
screen after completing the update and 
then automatically restarts the TV. Press 
; to complete the operation.
3
•
••
•
•
•
•
•
4
5
6
•
Information on the software license for this product
Software compositionThe software included in this product is comprised of various software components whose individual copyrights are held by SHARP or by 
third parties.
Software developed by SHARP and open source software The copyrights for the software components and various relevant documents included with this product that were developed or written 
by SHARP are owned by SHARP and are protected by the Copyright Act, international treaties, and other relevant laws. This product also 
makes use of freely distributed software and software components whose copyrights are held by third parties. These include software 
components covered by a GNU General Public License (hereafter GPL), a GNU Lesser General Public License (hereafter LGPL) or other 
license agreement.
Obtaining source code Some of the open source software licensors require the distributor to provide the source code with the executable software components. 
GPL and LGPL include similar requirements. For information on obtaining the source code for the open source software and for obtaining 
the GPL, LGPL, and other license agreement information, visit the following website:
http://www.sharp-eu.com/gpl/
We are unable to answer any questions about the source code for the open source software. The source code for the software 
components whose copyrights are held by SHARP is not distributed.
Acknowledgements The following open source software components are included in this product:
• linux kernel • busy box • uClibc • zlib • libpng • libjpeg • mt\
d-utils
LC-LE705E_GB.indd   43 LC-LE705E_GB.indd   43 2009/10/09   14:13:25
2009/10/09   14:13:25
 
						

							44
Specifications
ItemLCD COLOUR TV (32 o), LC-
32LE700E, LC-32LE700S, 
LC-32LX700E, LC-32LU700E, 
LC-32LU700S, LC-32LE705E, 
LC-32LE705S, LC-32LX705E, LC-
32LU705E, LC-32LU705SLCD COLOUR TV (40 o), LC-
40LE700E, LC-40LE700S, 
LC-40LX700E, LC-40LU700E, 
LC-40LU700S, LC-40LE705E, 
LC-40LE705S, LC-40LX705E, LC-
40LU705E, LC-40LU705S
LCD panel Advanced Super View & BLACK TFT  LCD (32 o)Advanced Super View & BLACK TFT 
LCD (40 o)
Resolution 2,073,600 pixels (1,920 x 1,080)
Video colour system PAL/SECAM/NTSC 3.58/NTSC 4.43/PAL 60
TV function TV-standard Analogue CCIR (B/G, I, D/K, L/L’) Digital DVB-T (2K/8K OFDM), DVB-C
Receiving 
channel VHF/UHF
IR A ch_E69 ch (Digital), E2_E69 ch, F2_F10 ch, I21_I69 ch, IR A_IR J ch
CATV Hyper-band, S1_S41 ch
TV-tuning system Auto Preset 999 ch (non-Nordic [DTV]), Auto Preset 9999 ch (Nordic [DTV]), Auto 
Preset 99 ch (ATV), Auto Label, Auto Sort
STEREO/BILINGUAL NICAM/A2
Audio amplifier 10 W x 2
Speaker (35 mm x 100 mm) x 2
Terminals Antenna UHF/VHF 75 q Din type (analogue & digital)
RS-232C D-Sub 9 pin male connector
EXT 1 SCART (AV input, Y/C input, RGB input, TV output)
EXT 2 SCART (AV input/monitor output, Y/C input)
EXT 3 COMPONENT IN (Y/P
B(CB)/PR(CR), RCA pin (AUDIO R/L))
EXT 4 15 pin mini D-sub
HDMI 1 (EXT 5) HDMI
HDMI 2 (EXT 6) HDMI
HDMI 3 (EXT 7) HDMI
HDMI 4 (EXT 8) HDMI
EXT 9 RCA pin (AV input)
USB USB
HDMI 2/PC AUDIO (R/L) Ø 3.5 mm jack*
1
DIGITAL AUDIO OUTPUTOptical S/PDIF digital audio output
C. I. (Common Interface) EN50221, R206001, CI Plus specification
OUTPUTRCA pin (AUDIO R/L)
Headphones Ø 3.5 mm jack (audio output)
OSD language Czech, Danish, Dutch, English, Estonian, Finnish, French, German, Greek, 
Hungarian, Italian, Latvian, Lithuanian, Norwegian, Polish, Portuguese, \
Russian, 
Slovak, Slovene, Spanish, Swedish, Turkish, Ukrainian
Power requirement AC 220_240 V, 50 Hz
Power consumption (method IEC62087) 93 W (0.2 W standby*
2)133 W (0.2 W standby*2)
Weight 10.5 kg (without stand), 13.5 kg (with 
stand)12.3 kg (without stand), 16.2 kg (with 
stand)
Operating temperature 0 °C to e 40 °C
The HDMI 2 and EXT 4 terminals can both use the same audio input termina\
l.
Standby power consumption applies when the TV is set to not receive EPG data.
I
J
Appendix
LC-LE705E_GB.indd   44 LC-LE705E_GB.indd   44 2009/10/09   14:13:26
2009/10/09   14:13:26
 
						

							45
ItemLCD COLOUR TV (46 o), LC-
46LE700E, LC-46LE700S, 
LC-46LX700E, LC-46LU700E, 
LC-46LU700S, LC-46LE705E, 
LC-46LE705S, LC-46LX705E, LC-
46LU705E, LC-46LU705SLCD COLOUR TV (52 o), LC-
52LE700E, LC-52LE700S, LC-
52LE705E, LC-52LE705S
LCD panel Advanced Super View & BLACK TFT  LCD (46 o)Advanced Super View & BLACK TFT 
LCD (52 o)
Resolution 2,073,600 pixels (1,920 x 1,080)
Video colour system PAL/SECAM/NTSC 3.58/NTSC 4.43/PAL 60
TV function TV-standard Analogue CCIR (B/G, I, D/K, L/L’) Digital DVB-T (2K/8K OFDM), DVB-C
Receiving 
channel VHF/UHF
IR A ch_E69 ch (Digital), E2_E69 ch, F2_F10 ch, I21_I69 ch, IR A_IR J ch
CATV Hyper-band, S1_S41 ch
TV-tuning system Auto Preset 999 ch (non-Nordic [DTV]), Auto Preset 9999 ch (Nordic [DTV]), Auto 
Preset 99 ch (ATV), Auto Label, Auto Sort
STEREO/BILINGUAL NICAM/A2
Audio amplifier 10 W x 2
Speaker (35 mm x 100 mm) x 2
Terminals Antenna UHF/VHF 75 q Din type (analogue & digital)
RS-232C D-Sub 9 pin male connector
EXT 1 SCART (AV input, Y/C input, RGB input, TV output)
EXT 2 SCART (AV input/monitor output, Y/C input)
EXT 3 COMPONENT IN (Y/P
B(CB)/PR(CR), RCA pin (AUDIO R/L))
EXT 4 15 pin mini D-sub
HDMI 1 (EXT 5) HDMI
HDMI 2 (EXT 6) HDMI
HDMI 3 (EXT 7) HDMI
HDMI 4 (EXT 8) HDMI
EXT 9 RCA pin (AV input)
USB USB
HDMI 2/PC AUDIO (R/L) Ø 3.5 mm jack*
1
DIGITAL AUDIO OUTPUTOptical S/PDIF digital audio output
C. I. (Common Interface) EN50221, R206001, CI Plus specification
OUTPUTRCA pin (AUDIO R/L)
Headphones Ø 3.5 mm jack (audio output)
OSD language Czech, Danish, Dutch, English, Estonian, Finnish, French, German, Greek, 
Hungarian, Italian, Latvian, Lithuanian, Norwegian, Polish, Portuguese, \
Russian, 
Slovak, Slovene, Spanish, Swedish, Turkish, Ukrainian
Power requirement AC 220_240 V, 50 Hz
Power consumption (method IEC62087) 162 W (0.2 W standby*
2)189 W (0.2 W standby*2)
Weight 18.5 kg (without stand), 23.5 kg (with 
stand)22.5 kg (without stand), 27.6 kg (with 
stand)
Operating temperature 0 °C to e 40 °C
The HDMI 2 and EXT 4 terminals can both use the same audio input termina\
l.
Standby power consumption applies when the TV is set to not receive EPG data.
As a part of our policy of continuous improvement, SHARP reserves the right to make design and specification changes for product 
improvement without prior notice. The performance specification figures indicated are nominal values of production units. There may be 
some deviations from these values in individual units.
NOTERefer to the inside back cover for dimensional drawings.
I
J
•
•
Appendix
LC-LE705E_GB.indd   45 LC-LE705E_GB.indd   45 2009/10/09   14:13:26
2009/10/09   14:13:26
 
						

							46
Environmental specifications
Item32 inch 
models 40 inch 
models 46 inch 
models 52 inch 
models
I On-Mode (W) (HOME MODE)
60 W 72 W 89 W 98 W
J Energy-Save-Mode (W)
Advanced54 W70 W81 W92 W
K Standby-Mode (W)
0.20 W 0.20 W 0.20 W 0.20 W
L Off Mode (W) Power button 0.19 W 0.19 W 0.19 W 0.19 W
MAIN POWER 
switch
0.01 W or less 0.01 W or less 0.01 W or less 0.01 W or less
M Annual Energy Consumption (kWh)
87.6 kWh 105.1 kWh 129.9 kWh 143.1 kWh
N Annual Energy Consumptioning 
Energy-Save-Mode (kWh)
Advanced
78.8 kWh 102.2 kWh 118.3 kWh 134.3 kWh
Measured according to IEC 62087 Ed. 2
For further information about the Energy Save function, please see related pages in this operation manual
Measured according to IEC 62301 Ed. 1
Measured according to IEC 62301 Ed. 1
Annual energy consumption is calculated on the basis of the On-Mode (HO\
ME MODE) power consumption, watching TV 4 hours a day, 
365 days a year
Annual energy consumption is calculated on the basis of the Energy-Save-\
Mode power consumption, watching TV 4 hours a day, 365 
days a year
NOTEThe power consumption of On-Mode varies depending on the images the TV d\
isplays.
Optional accessories
The listed optional accessories are available for this LCD colour TV. Please purchase them at your nearest shop.Additional optional accessories may be available in the near future. When purchasing, please read the newest catalogue for compatibility 
and check the availability.
No. Part name Part number Notes
1 Wall mount bracket (32 inch models) AN-37AG5The centre of the TV screen is 5 mm below the mark “B” on 
the wall bracket.
2 Wall mount bracket (40 inch models) AN-37AG2
The centre of the TV screen is 20 mm below the mark “B” on 
the wall bracket.
3 Attachment (40 inch models) AN-37P30
4 Wall mount bracket (46 inch models) AN-52AG4The centre of the TV screen is 1.3 mm below the mark “b” on 
the wall bracket.
5 Wall mount bracket (52 inch models) AN-52AG4The centre of the TV screen is 1.75 mm below the mark “b” 
on the wall bracket.
I
J
K
L
M
N
•
•
Appendix
LC-LE705E_GB.indd   46 LC-LE705E_GB.indd   46
2009/10/09   14:13:26
2009/10/09   14:13:26
 
						

							47
Rating table for child lock
User-adjusted ratingBroadcasted rating
AGE
4 5 6 7 8 9 10 11 12 13 14 15 16 17 18
Universal viewing ✔——————————————
Parental approval  pref. ✔✔✔✔✔
——————————
X-rated ✔✔✔✔✔✔✔✔✔✔✔✔✔✔✔
User-adjusted rating Broadcasted rating
Universal viewing Parental approval pref. X-rated
Universal viewing ———
Parental approval  pref. ✔
——
X-rated ✔✔ —
Abbreviation list
Abbreviated term
Stands for
AT V Analogue TV
CEC Consumer Electronics Control
: Digital Noise Reduction
DTV Digital TV
DVB-C Digital Video Broadcasting-Cable
DVB-T Digital Video Broadcasting-Terrestrial
DVI Digital Visual Interface
EPG Electronic Pogramme Guide
HDCP High-bandwidth Digital Content Protection
HDMI High-Definition Multimedia Interface
MHEG Multimedia and Hypermedia Expert Group
OSD On Screen Display
PCM Pulse Code Modulation
USB Universal Serial Bus
WSS Wide Screen Signalling
WYSIWYR What You See Is What You Record
Appendix
LC-LE705E_GB.indd   47
LC-LE705E_GB.indd   47 2009/10/09   14:13:27
2009/10/09   14:13:27
 
						

							48
End of life disposal
Appendix
LC-LE705E_GB.indd   48
LC-LE705E_GB.indd   482009/10/09   14:13:27
2009/10/09   14:13:27