Sharp Lc 32fs510 Operation Manual

E665WJZZ3
TINS-E665WJZZ10P05-SP
PIN
SHARP ELECTRÓNICA ESPAÑA S.A
Polígono Industrial Can Sant Joan
Calle Sena 2-10
08174 SANT CUGAT DEL VALLÉS
BARCELONA (ESPAÑA)SHARP CORPORATION
http://www.sharp-eu.com
Tiskano v Španiji 
Wydrukowano w Hiszpanii
Készült Spanyolország
Vytištěno v Španělsko
Vytlačené v Španija
Надруковано  в Іспанія
Trükitud Hispaania
Iespiests Spānija
Išspausdinta Ispanija
Τυπώθηκε  στην Ισπανία
İspanya’da basılmıştır
Printed in Spain...

200.0143.6
200.0
245
105
76
64
773
699.2
393.8
517 57457
475.4
326.2
USBMEDIAPLAYERC.IMENUP
LC-32FH500E / LC-32FH500S / LC-32FB500E / LC-32FB500S / LC-32FH510E 
LC-32FH510S / LC-32FB510E / LC-32FB510S / LC-32FS510E / LC-32FS510S
SPECIAL NOTE FOR USERS IN THE U.K.
The mains lead of this product is fitted with a non-rewireable (moulded\
) plug incorporating a 13A fuse. Should 
the fuse need to be replaced, a BSI or ASTA approved BS 1362 fuse marked 
 or 
 and of the same rating as 
above, which is also...

OPERATION MANUAL
Contents  ....................................................................... 1
Introduction  ................................................................ 2
Dear SHARP customer ................................................. 2
Important Safety Precautions  ....................................... 2
Trademarks  .................................................................. 2
Remote Control unit  ..................................................... 3
TV (Front view)...

•  Cleaning—Unplug the AC cord from the AC outlet before cleaning the product. Use a damp cloth to clean the product. 
Do not use liquid cleaners or aerosol cleaners.
•  Use a soft damp cloth to gently wipe the panel when it is dirty. To protect the panel, do not use a chemical cloth to clean 
it. Chemicals may cause damage or cracks in the cabient of the TV.
•  Water and moisture—Do not use the product near water, such as bathtub, washbasin, kitchen sink, 
laundry tub, swimming pool and in a wet...

Introduction
Remote control unit
	









	
		
	

	
		 	
	
	 	



	


















1 B Standby/On
 Enter standby mode or turn on the
 power.
2 p Channel information / EPG
 (See pages 11 and 20.)
3 DTV MENU
 Display the MEDIA PLAYER screen.
4 0–9
 Set the channel in TV mode. 
  Set the page in Teletext mode.
5 A Flashback
 Press to return to the previous
  selected channel or external input
 mode.
6 DTV
 Change between ATV and DTV
 mode.
7 f Picture format
Change between...

TV (Front view)
TV (Top and rear view)
Remote control sensor B (Standby/On) indicator
Introduction
WARNING•  Excessive sound pressure from earphones and headphones can cause hearing loss.
•  Do not set the volume at a high level. Hearing experts advise against extended listening at high volume levels. a (Power button)
(MENU button)
 b (INPUT SOURCE button)
i(k/l) (Volume buttons) P(r/s)
(Programme (channel) buttons)
1 USB terminal
2  COMPONENTS / AV terminals
3 HEADPHONES jack
4  SCART 1 (AV/RGB)...

1 Confirm that there are eight screws with the stand unit.
2 Attach the supporting post for the stand unit onto the base using the four screws with the screw driver (supplied) 
as shown.
3  Inserting the stand.
Insert the stand into the openings on the bottom of the TV (Hold the stand so it will not drop from the edge 
of the base area).
Insert and tighten the four screws into the four holes on the rear of the TV.
NOTE
• To detach the stand unit, perform the above steps in reverse order.
Remote...

Preparation
Inserting the batteries
Before using the TV for the first time, insert two supplied “AA” size zinc-carbon batteries. When the batteries become 
depleted and the remote control unit fails to operate, replace the batteries with new “AA” size batteries.
1 Hold in the tab on the battery cover and pull the cover towards the direction of the arrow.
2 Insert two supplied “AA” size batteries.
• Place batteries with their terminals corresponding to
 the (+) and (-) indications in the battery...

Quick guide
123
Initial installation overview
Follow the steps below one by one when using the TV for the first time. Some steps may not be necessary 
depending on your TV installation and connection.
  Connect an antenna cable to 
the antenna terminal (Page 8).
  If necessary, insert a CA card 
into the CI slot to watch 
scrambled broadcasts
 (Page 8.)
  Connect the AC cord to the TV 
(Page 8).
Product shape varies in some countries.
  Turn on the power using a on 
the TV (Page 10).
  Run the...

Quick guide
Before turning on the power
In order to receive coded digital stations, a Common 
Interface Module (CI Module) and a CA Card must be 
inserted in the CI slot of the TV.
The CI Module and the CA Card are not supplied 
accessories. They are usually available from your 
dealers.
Inserting the CA Card into the CI Module
  1With the side with the gold coloured contact 
chip facing the side of the CI Module marked 
with the provider’s logo, push the CA Card 
into the CI Module as far as it will go....