Sharp AR C360P User Manual

2
3. Install the metal brackets where the 
breakout panels were.
4. Open the face-up stacker (
!), then open 
the flap and press it onto the stacker surface 
(
).
5. Close the stacker.
Step 2: Prepare the Inverter
Before assembling the finisher, you must adjust the 
height of the inverter unit to match the finisher:
!Inverter as supplied
Inverter changed for use with 4-tray 
finisher.
1. Unpack the inverter and remove any packing 
materials.
Downloaded From ManualsPrinter.com Manuals 

3
2. Remove the two bottom caps:
a. Turn the inverter over. 
b. Remove the two screws securing the bottom 
caps on either side of the inverter.
c. Remove the end caps and store them along 
with the four screws in case you ever need 
to convert the unit back.3. Turn the inverter around and remove the 
screws holding the metal brackets in place. 
Keep the screws and brackets handy: they are 
used to help secure the extension plate once it 
is repositioned.
4. Turn the inverter around and remove the 
two...

4
5. Pull forward on the extension plate to 
disengage the pins from the top channel stops, 
then slide it down into the inverter and push 
back to engage the pins on the bottom channel 
stops.
6. Reattach the extension plate using the 
screws you removed earlier.7. Turn the inverter around and reinstall the 
brackets.
Step 3: Assemble the Inverter
1. Place the hooks on the bottom of the 
inverter into the slots on the inverter stand, 
then slide the inverter to lock the hooks in 
place.
Downloaded From...

5
2. Attach the front of the inverter to the stand 
using two screws on either side.
3. Attach the back of the inverter to the stand 
using one screw on either side.
4. Attach the guard rail on the inverter stand to 
the printer using 2 screws. Step 4: Assemble the Finisher
1. Hook the finisher stand onto the inverter.
2. Attach the finisher stand to the inverter with 
2 screws.
Downloaded From ManualsPrinter.com Manuals 

6
3. Place the finisher cover near the back of the 
finisher. Locate the tab (
!) on the right side of 
the cover.
4. Hold the clear band perpendicular to the cover 
and slip one end over the tab (
!), then pivot 
the band 90 degrees (
) so that it is aimed 
toward the finisher:
5. Slip the other end of the band (!) through 
the retainer on the finisher and secure it 
with the small stopper (
).6. Place the large stopper over the tab on the 
cover and turn it to lock it in position.
7. Attach the cover...

7
8. Pull the finisher platform about half way out, 
then loosen the screw on the locking piece (
!: 
viewed from the opposite direction) so that it 
drops through the slot below it. This keeps the 
platform from moving while you attach the 
finisher to it.
9. Position the finisher on the stand and attach 
it with two screws from the back.
10. Lift the locking piece back up and tighten the 
screw firmly. Be sure it’s out of the way and 
the screw is tight—otherwise the platform 
will not move freely.
11....

12. Secure the stacker with four screws.
13. Push the finisher against the printer until the 
prongs on the printer brackets fit into the 
holes in the finisher. 
Note:If you need to, turn the levellers (!) on 
either side of the finisher to raise or 
lower it so the holes and prongs align 
properly. Make sure the finisher is level.
Step 5: Make Connections
1. Connect the finisher’s cable to the inverter 
(
!). Use the cable supplied to connect the 
inverter to the printer (
).
2. Plug the power cord...

9
Application Notes & Tips
Using the Single Staple Feature
There is a Staple dropdown selection within the 
Finishing Properties of the Fiery.
There are 4 single staple options within that 
dropdown. The choices are:
• Top Left    Horizontal
• Top Left    Vertical
•Top Right  Horizontal
• Top Right  Vertical
Use the following procedure for these choices to 
work correctly.
1. Configure the trays for the proper 
orientation (SEF or LEF). 
2. Select the Page Size within Paper Source to 
SEF or LEF.
3. For...

10
Saddle Stitching on Tabloid Paper
This section explains how to saddle stitch on 
Tabloid size paper, using the Postscript Driver (PS) 
and MS Word as an example.
1. Click File then Page Setup. 
2. Under Page Setup click on the Paper tab. 
Choose the correct Paper size. then click OK.
3. Click File and select Print. The Printer dialog 
box appears. 
4. Click Printer Properties. The Printer 
Properties dialog box appears.
5. Change the following settings under the 
appropriate dropdown list.
Paper...