Sharp AR 5516 User Manual

							69
TROUBLESHOOTING
6
A Notice Page (NP-001) has been 
printed, but the print data has not 
been printed completely.A print job containing more data than can be held in the 
print memory is sent to the machine.→Disable the ROPM function on the Configuration tab of the 
printer driver setup screen. If you need to use the ROPM function, 
divide the pages of the print data into two or more print jobs.
→The memory allocated to the printer function can be changed in 
the system setting Memory allocated to printer mode.
58
Printing is slow.Simultaneous use of two or more application software 
programs.
→Start printing after quitting all unused application software programs.
–
The printed image is light and 
uneven.The paper is loaded so that printing takes place on the 
back side of the paper.
→Some paper types have a front and back side. If the paper is 
loaded so that printing takes place on the back side, toner will not 
adhere well to the paper and a good image will not be obtained.10
The printed image is dirty.You are using paper that is outside the specified size and 
weight range.
→Use copy paper within the specified range.
9
Paper curled or damp.
→Do not use curled or crimped paper. Replace with dry copy paper. 
During periods when the machine is not used for a long time, 
remove the paper from the tray and store it in a dark place in a 
bag to prevent moisture absorption.
–
You did not set sufficient margins in the paper settings of 
your application.
→The top and bottom of the paper may be dirty if the margins are 
set outside of the specified print quality area.
→Set the margins in the software application within the specified 
print quality area.–
The printed image is skewed or it 
runs off the paper.The paper loaded in the tray is not the same size as that 
specified in the printer driver.
→Check if the Paper Size options suit the size of the paper loaded 
in the tray.
→If the Fit To Paper Size setting is activated, make sure that the 
paper size selected from the drop-down list is the same as the 
size of the loaded paper.
–
The orientation of document setting is not correct.
→Click the Main tab in the printer driver setup screen, and verify if 
the Image Orientation option is set to your requirements.–
Paper is not loaded properly.
→Make sure the paper is properly loaded.10
You did not correctly specify the margins for the 
application in use.
→Check the layout of the document margins and the paper size 
settings for the application you are using. Also check if the print 
settings are specified correctly to suit the paper size.–
The printed image is darker or 
lighter than expected.The setting for the print density is not appropriate. 
→You can adjust the print density on the printer driver. Click the 
Advanced tab in the printer driver setup screen, and click the 
Compatibility button. Select the Print Density Level from 
1 (light) to 5 (dark).
–
Any one of the alarm indicators 
(,, , ,) is lit or 
blinking.See INDICATORS AND DISPLAY MESSAGES to check 
the meaning of the alarm indicator and error message in 
the display, and take appropriate action.72
ProblemCause and solutionPage
Downloaded From ManualsPrinter.com Manuals 
						

							70
TROUBLESHOOTING
Poor scanning quality.The document glass or the underside of the document 
cover/SPF/RSPF is dirty.
→Clean regularly.
83
Original smudged or blotchy.
→Use a clean original.–
You have not specified a suitable resolution.
→Make sure that the resolution setting in the scanner driver is 
appropriate for the original.–
You are scanning a large area (for example an entire A3) 
at high resolution.
→If you attempt to scan a large area at high resolution and there is 
insufficient memory in the machine to hold the scanned data, 
scanning will take place at a lower resolution and the scanner 
driver will enhance the data to make up for the lower resolution. 
However, the quality of the enhanced image will not be as high as 
if scanning took place at the higher resolution. Use a lower 
resolution setting, or scan a smaller area.
–
You have not specified a suitable value for the B/W 
Threshold setting.
→If you are scanning with a TWAIN-compliant application, make 
sure that a suitable value is specified for the B/W Threshold 
setting. A larger threshold value makes your output darker, while 
a small threshold value makes it lighter. To adjust the threshold 
automatically, click the Auto Threshold button on the Image 
tab of the Professional screen.
–
The brightness and contrast settings are not suitable.
→If you are scanning with a TWAIN-compliant application and the 
resulting image has unsuitable brightness or contrast (for 
example it is too bright), click the Auto Brightness/Contrast 
Adjustment button on the Colour tab of the Professional 
screen. Click the Brightness/Contrast button to adjust the 
brightness and the contrast while viewing the scanned output 
image on the screen. If you are scanning with a WIA-compliant 
application or the Scanner and Camera Wizard, click Adjust the 
quality of the scanned picture or the Custom settings button, 
and adjust the brightness and contrast in the screen that appears.
–
The original is not placed face up in the SPF/RSPF or face 
down on the document glass.
→Place the original face up in the SPF/RSPF or face down on the 
document glass.15, 16
The original was not placed in the correct position.
→Place the original correctly.15, 16
ProblemCause and solutionPage
Downloaded From ManualsPrinter.com Manuals 
						

							71
TROUBLESHOOTING
6
Unable to scan the image.If scanning is not possible, shut down your computer, 
turn off the machine’s power switch, and unplug the 
machine’s power cord. Next, start your computer, restore 
power to the machine, and try scanning again. If scanning 
is still not possible, check the following items.–
Your application is not TWAIN/WIA compliant.
→If your application is not TWAIN/WIA compliant, scanning will not 
be possible. Make sure your application is TWAIN/WIA compliant.–
You have not selected the scanner driver of the machine 
in your application.
→Make sure that the machine’s scanner driver is selected in your 
TWAIN/WIA-compliant application.–
You have not specified all scanning preferences 
appropriately.
→Scanning a large area at high resolution results in a large amount 
of data and extended scanning times. The scanning preferences 
should be set appropriately for type of original to be scanned, i.e., 
Text, Text/Graphics, Photograph.–
There is not enough machine memory.
→The scan resolution will vary depending on the scanning area and 
how much memory in the machine is free.–
Scanner transfer speed is slow.Your computer does not meet the system requirements 
for the USB 2.0 interface (Hi-Speed mode).
→See System requirements for USB 2.0 (Hi-Speed mode) in the 
Start Guide to configure your system as required for USB 2.0, 
and check if Hi-Speed is set.Start 
Guide, 
58
ProblemCause and solutionPage
Downloaded From ManualsPrinter.com Manuals 
						

							72
INDICATORS AND DISPLAY MESSAGES
If one of the following indicators lights up or one of the following messages appears in the display, check the 
meaning of the indicator or message in the following table and take appropriate action.
IndicationCause and solutionPage
Maintenance 
indicatorSteadily 
litService by an authorised SHARP service technician is 
required.–
Developer 
replacement 
required indicatorSteadily 
litDeveloper is required. Contact your authorised service 
representative.–
Toner cartridge 
replacement 
required indicatorSteadily 
litReplacement of toner cartridge will be needed soon. Prepare a 
new cartridge.–
Blinking
 Toner cartridge must be replaced. Replace it with a new one.
 Toner is being fed.80
Paper required 
indicatorSteadily 
litThe tray is out of paper. Load paper. It is also possible that the 
tray is not inserted completely into the machine. Make sure it is 
inserted correctly. 10
Misfeed indicatorBlinkingA paper misfeed has occurred. Remove the misfeed as 
explained in MISFEED REMOVAL.73
ORIGINAL SIZE indicator BlinkingThe original is not placed in the correct orientation. Rotate the 
original so that it is in the same orientation as the blinking 
ORIGINAL SIZE indicator.15,16
PAPER SIZE indicator Blinking
A blinking PAPER SIZE indicator means that the size of paper loaded 
in the tray is different from the paper size setting for the tray. Change 
the paper size setting.
To clear the display, do one of the following:
 Use the [PAPER SELECT] key ( ) to change the tray selection.
 Open and close the tray.
 Press the [CLEAR ALL] key ( ).
12
[CH] appears in displaySteadily 
litThe front cover or the side cover is open. Close the front cover 
or the side cover.–
Blinking
The toner cartridge is not installed correctly. Reinstall the toner 
cartridge. If [CH] still blinks in the display after reinstalling the toner 
cartridge, contact your authorised service representative.
80
Letters and numbers appear 
in the display
Turn off the power switch, wait about 10 seconds, and then turn on 
the switch again. If this does not clear the message, write down 
the code (Main code and sub code exists.) that appears and then 
unplug the power cord and contact your authorised service 
representative. Tell your authorised service representative what 
code appeared and the circumstances under which it appeared.
–
FUL appears in the displayData is being held in memory. Print the data or clear it from 
memory.
30, 32
When Use close paper size is disabled
Press the [PAPER SELECT] key ( ) to manually select the 
tray and then press the [ON LINE] key ( ). Printing will 
begin. If you are selecting the bypass tray, load paper in the 
bypass tray.36
Misfeed location indicator lights up at 
the optional 2 x 250-sheet/250-sheet 
paper feed unit
The side cover of the 2 x 250-sheet/250-sheet paper feed unit 
is open. Close the side cover.–
Misfeed indicator Paper required indicatorMaintenance indicator
Toner cartridge replacement 
required indicator
Developer replacement 
required indicator
Display
Downloaded From ManualsPrinter.com Manuals 
						

							
73
6
MISFEED REMOVAL
When a misfeed occurs, the misfeed indicator ( ) and a misfeed location indicator ( ) will blink and the machine 
will automatically stop.
Check the blinking misfeed location indicator to identify the location of the misfeed and remove it.
MISFEED IN THE SPF/RSPF
1Remove the misfed original.
Check sections A, B, and 
C in the left shows the 
illustration (see the next 
page), and remove the 
misfed original.
Section A
Open the feeding roller cover and remove the 
misfed original from the document feeder tray. 
Close the feedin g roller cover. 
Section B
Open the SPF/RSPF and rotate the two release 
rollers in the direction  of the arrow to feed the 
original out. Close the SPF/RSPF and then 
remove the original.
If a small original (A5 etc.) is misfed, open the 
right side cover and remove the original. Close 
the right side cover.
The paper may tear when you remove a misfeed. In this even t, be sure to remove all torn pieces of paper from the 
machine, taking care not to touch the photoconductive  drum (the green part). Any scratches or damage to the 
surface of the drum will cause dirty copies.Note
(p.73)
(p.74)
(p.78)
(p.79)
Feeding roller cover
Roller
Right side cover
Downloaded From ManualsPrinter.com Manuals 
						

							
74
TROUBLESHOOTING
Section C
Remove the misfed original from the exit area.
If the misfed original cannot be easily removed 
from the exit area, open the moveable part of the 
document feeder tray and remove the original. 
2Open and close the SPF/RSPF to 
make the misfeed l ocation indicator 
stop blinking.
You can also make the 
misfeed indicator stop 
blinking by opening and 
closing the feeding roller 
cover or the right side 
cover.
3Return the originals indicated by the 
minus number in th e display to the 
document feeder tray  and press the 
[START] key ( ).
Copying will resume from the originals that still 
remained when the misfeed occurred.
MISFEED IN THE BYPASS TRAY
1Gently pull the mi sfed paper out.2Open and close the side cover.
The misfeed indicator 
( ) will go out.
• When closing the side cover, press down on 
the handle.
 If the misfeed indicator ( ) does not stop  blinking, check for torn pieces of paper in 
the machine.Note
Downloaded From ManualsPrinter.com Manuals 
						

							75
TROUBLESHOOTING
6
MISFEED IN THE MACHINE
1Open the bypass tray and the side 
cover. 2Check the misfeed location. Remove 
the misfed paper following the 
instructions for each location in the 
illustration below.
A. Misfeed in the paper feed area
1Push gently on both ends of the front 
cover and open it.
2Carefully remove the misfed paper. 
Turn the roller rotating knob in the 
direction of the arrow to assist in 
removing it.
Be careful not to tear the 
misfed paper during 
removal.
3Close the front cover and side cover.
The misfeed indicator 
( ) will go out.
If paper is misfed here, go to
 B. Misfeed in the fusing area.
If paper is misfed here, go to 
A. Misfeed in the paper feed 
area. If the misfed paper is visible 
here, go to C. Misfeed in the 
transport area.
The fusing unit is hot. Do not touch 
the fusing unit when removing misfed 
paper. Doing so may cause a burn or 
injury.
Do not touch the photoconductive drum 
(green portion) when removing the misfed 
paper. Doing so may damage the drum and 
cause smudges on copies.
Roller rotating knob
Warning
Caution
 When closing the front cover, gently hold 
both ends.
 When closing the side cover, press on the 
handle.
 If the misfeed indicator ( ) does not stop 
blinking, check for torn pieces of paper in 
the machine.Note
Downloaded From ManualsPrinter.com Manuals 
						

							76
TROUBLESHOOTING
B. Misfeed in the fusing area
1Push gently on both ends of the front 
cover and open it.
2Turn the roller rotating knob in the 
direction of the arrow.
3Carefully remove the misfed paper. 
Lower the fusing unit release levers to 
allow easier removal.
Be careful not to tear the 
misfed paper during 
removal.
4Lift the fusing unit release levers, to 
return them to their operating 
positions.
5Close the front cover and side cover.
The misfeed indicator 
( ) will go out.
The fusing unit is hot. Do not touch 
the fusing unit when removing misfed 
paper. Doing so may cause a burn or 
injury.
 Do not touch the photoconductive drum 
(green portion) when removing the misfed 
paper. Doing so may damage the drum and 
cause smudges on copies.
 Be careful about unfixed toner on the 
misfed paper not to soil your hands or 
clothes.
Roller rotating knob
Fusing unit 
release lever
Warning
Caution
 When closing the front cover, gently hold 
both ends.
 When closing the side cover, press on the 
handle.
 If the misfeed indicator ( ) does not stop 
blinking, check for torn pieces of paper in 
the machine.Note
Downloaded From ManualsPrinter.com Manuals 
						

							77
TROUBLESHOOTING
6
C. Misfeed in the transport area
1Open the fusing paper guide by 
pressing down the green-labeled 
projection on the guide and remove 
the misfed paper.
Be careful not to tear the 
misfed paper during 
removal.
2If the misfed paper cannot be removed 
by the previous step but is visible in 
the paper output area, remove the 
paper by pulling it into the paper 
output area.
Be careful not to tear the 
misfed paper during 
removal.
3Close the side cover.
The misfeed indicator 
( ) will go out.
The fusing unit is hot. Do not touch 
the fusing unit when removing misfed 
paper. Doing so may cause a burn or 
injury.
 When closing the side cover, press on the 
handle.
 If the paper was torn, make sure that no 
torn pieces remain in the machine.
 If the misfeed indicator ( ) does not stop 
blinking, check for torn pieces of paper in 
the machine.
Warning
Note
Downloaded From ManualsPrinter.com Manuals 
						

							78
TROUBLESHOOTING
MISFEED IN THE UPPER PAPER TRAY
1Lift and pull out the upper paper tray 
and remove the misfed paper.
Be careful not to tear the 
misfed paper during 
removal.
2Open and close the side cover.
The misfeed indicator 
( ) will go out.
3Close the upper paper tray.
Push the upper paper 
tray in completely.
Make sure that there is no misfed paper in the tray before pulling it out. (p.75)Note
 When closing the side cover, press on the 
handle.
 If the misfeed indicator ( ) does not stop 
blinking, check for torn pieces of paper in 
the machine.Note
Downloaded From ManualsPrinter.com Manuals