Sega Virtua Tennis Owners Manual

28Clears the contents of BOOKKEEPING and high
score player ranking entry.
When clearing, bring the arrow to “YES” and when
not clearing, to “NO”, by using the SERVICE
BUTTON, and push the TEST BUTTON.
When the data has been cleared, “COMPLETED”
will be displayed. Bring the arrow to “NO” and
press the TEST BUTTON to cause the MENU
mode to return on to the screen.
Note that the contents of the GAME SETTING,
COIN SETTING, and BOARD SETTING are not
affected by BACKUP DATA CLEAR operation. BACKUP DATA CLEAR...

29 8. CONTROL PANELIn order to prevent an electric shock and short circuit, be sure to turn power off
before performing work by touching the interior parts of the product.
Be careful so as not to damage wirings. Damaged wiring can cause an electric shock
or short circuit accident.
Do not touch undesignated areas. Touching undesignated areas can cause electrical
shock or short circuit.
This work should be performed by the Location’s Maintenance Man or Serviceman.
Performing work by non-technical personnel...

30 HOW TO REPLACE INSTRUCTION SHEET12Turn power OFF by using the Main SW of AC Unit or the SUB PWR SUPPLY SW inside the SERVICE DOOR.
Unlock the lock on the back of the Control Panel Base, and open the Control Panel Base.
From inside the Control Panel Base, remove the 4 L WASHERS from both sides of INSTRUCTION COVER by
removing the screw from each.
Remove the Instruction Cover to replace the Instruction Sheet.
By using ther reversed procedure, install the Instruction Cover by securing the 4L WASHERS. Pay...

31The coin selector should be cleaned
once every 3 months. When cleaning,
follow the procedure below:
Turn the power for the machine OFF.
Open the coin chute door.
Open the gate and dust off by using a
soft brush (made of wool, etc.).
Remove and cleen smears by using a
soft cloth dipped in water or diluted
chemical detergent and then squeezed
dry.
Remove the CRADLE.
When removing the retaining ring(E-
ring), be very careful so as not to bend
the shaft.
Remove stain from the shaft and pillow
portions by...

32OPTIONAL DOLLAR BILL ACCEPTOR
THE COIN DOOR ASSEMBLY USED ON VIRTUA TENNIS COMES
EQUIPPED TO ACCEPT A DOLLAR BILL ACCEPTOR. ALL NEEDED
WIRING CONNECTIONS ARE CONVIENENTLY LOCATED INSIDE THE
GAME FOR THIS APPLICATION.
THE COIN DOOR CAN ACCCOMMODATE THE FOLLOWING
VALIDATORS:
HOLE POSITION#1                 Mars 2000 series
(FORWARD-MOST POSITION)
HOLE POSITION#2                 Mars 2000 series
                   DBV45 (JCM)
HOLE POSITION #3                   CURRENTLY NOT USED
HOLE POSITION #4...

33 

34 10. MONITORWhen performing such work as installing and removing the monitor, inserting and disconnect-
ing the external connectors to and from monitor, be sure to disconnect the power connector
(plug) before starting work. Proceeding the work without following this instruction can cause
electric shock of malfunctioning.
Using the monitor by converting it  without obtaining a prior permission is not allowed. SEGA
shall not be liable for any malfunctioning and accident caused by said conversion.
Primary...

35For the purpose of static prevention,
special coating is applied to the CRT
face of this product. To protect the
coating, pay attention to the following
points. Damaging the coating film can
cause electric shock to the customers.
For the caution to be heeded  when
clearing, refer to the Section of Periodic
inspection Table.
Do not apply or rub with a hard item (a
rod with pointed edge, pen, etc.) to or
on C.R.T. surfaces.
Avoid applying stickers, seals, etc. on
the C.R.T. face.
Do not remove aluminum...

36When performing such work as monitor installation/removal, or inserting /disconnectiing the
exteernal Connector connected to teh monitor and it’s interiror, first be sure to disconect thje
power connector (plug). Working witht eh power plug as is connected can cause electric shock or
malfunctioning.
When performing work, be very careful. To avoid electric shock accidents, etc., personnel other
tha those who have technical expertise are not allowed to perform this work.
Perform work bny following the...

37 Take out the 4 tamperproof screws and the 2
screws, and remove the Front Panel.
Disconnect the 2 Connectors for the speakers.
Take out the 6 Tamperproof screws, and remove
the CRT Cover.
Disconnect the 2 Connectors connected to the
frame on the back side of CRT and the Connector
connected to the Printed Circuit Board to loosae
the secured wiring.
Remove the nuts securing the corners of the
monitor.
By holding the monitors sheet metal frame
portion, pull out from the cabinet.
At this time, be very...