Sanyo Vpc E60ex Instruction Manual

15English
PARTS NAMES
Rear
Bottom
DC IN terminalZoom switch
Playback 
button [H]
LCD monitorSET button
Tripod stand hole
Battery/card cover ON/OFF button
Strap holder
Multi-indicatorShutter button
USB/AV terminalMENU button
Downloaded From camera-usermanual.com Sanyo Manuals 

English16
INSTALLING THE CARD
Your camera has an internal 32MB memory, which means that you can take 
photos (record image data) even when no card is installed. By using a card, 
however, you will be able to take many more photos.
The card can be used after it has been formatted with the camera (page 137).
1 Open the battery/card cover.
hWhile gently pressing the battery/card cover, slide it open.
2 Insert the card, and close the battery/card cover.
hFirmly insert the card until it clicks into place....

17English
INSTALLING THE CARD
When removing the card...
hTo remove the card, press it down, and then release. The card will 
protrude slightly, and you can then pull it out.
CAUTION
iDo not attempt to forcibly remove the card.
iNever remove the card when the multi-indicator is flashing red quickly. In 
doing so, you risk losing the data stored in the card.
HINT
Shooting without a card installed
iThe camera has a 32MB internal memory that lets you photograph and 
play back images even when there is no...

English18
POWER FOR THE CAMERA
The supplied AC adaptor is used not only as the camera’s AC adaptor, but 
also to charge the battery installed in the camera.
Using the battery pack
At the time of purchase, the battery pack is not charged. The battery pack 
must be charged before it can be used in the camera. Also, if the battery 
power becomes depleted when the camera is being used (see CHECKING 
THE REMAINING BATTERY PACK CHARGE [page 142]), it should be 
recharged as soon as possible.
1 Install the...

19English
POWER FOR THE CAMERA
2 Turn the camera off, and connect the AC adaptor to the camera.
hCharging begins as soon as the AC adaptor is connected to the 
camera. However, the camera does not charge when it is set to the 
shooting mode.
hThe camera’s multi-indicator lights red during charging.
hCharging will take approximately 90 minutes.
hThe multi-indicator will turn off when the battery pack is fully charged.
3 Disconnect the AC adaptor after charging is completed.
Using a power outlet
When the...

English20
HINT
About the internal backup battery
iThis camera’s internal battery serves to maintain the date and time 
settings, as well as the shooting settings. The backup battery will be fully 
charged when the battery pack is kept in the camera continuously for about 
2 days. In the fully charged state, the backup battery will maintain the 
camera settings for about 7 days.
When not using the camera for a long time, remove the battery pack
iA small amount of power is still used even if the camera is...

21English
TURNING THE CAMERA ON AND OFF
Turning on the camera
In the shooting mode
1 Press the ON/OFF button.
hThe camera turns on.
hThe camera turns on in the 
shooting mode that was active 
before it was last turned off.
In the playback mode
1 Press the playback button [H] for at 
least one second.
hThe Playback Screen appears on 
the LCD monitor (page 35).
Turning off the camera
1 Press the ON/OFF button.
hThe camera turns off.

hWhen the playback button [H] or ON/OFF button is pressed, the 
camera...

English22
Turning on the camera when the power save (sleep) function is active
In order to preserve battery pack power, the power save (sleep) function will 
automatically turn off the camera after one minute of no use during shooting, 
or five minutes of no use during playback (factory-preset setting).
iWhen the power save function is active, you can restore the power by any 
of the following methods:
hPress the playback button [H].
hPress the SET or MENU button.
hPress the shutter button.
hPress the...

23English
DATE AND TIME SETTING
The camera will record the date and time an image or audio recording is 
taken so that you can display them during playback. Therefore, before 
capturing images, make sure the correct date and time are set.
Example: To set the clock to 7:30 p.m. on December 24, 2006
1 Press the ON/OFF button to turn the camera on, and press the MENU 
button.
2 Toggle the SET button down.
hThe Shooting Setting Screen appears (page 55).
3 Display the Option Screen 
(page 118).
4 Toggle the...

English24
5 Set the date.
1Select “DATE”.
2Press the SET button.
hThe Set Date Screen appears.
3Set the date to “2006/12/24”.
hThe date is set in the following 
order: Set the year → Set the 
month → Set the day.
hToggle the SET button left or 
right to select year, month or 
day. Toggle the SET button up 
or down to increase or decrease 
the number.
4Press the SET button.
6 Set the time.
1Select “TIME”.
2Press the SET button.
hThe Set Time Screen appears.
3Set the time to “19:30”.
hThe time is set in...