Sangean Ats606ap Shortwave Radio Owners Manual

3.Press repeatedly the[]or[V]buttons to reach
 a desired frequency. Press and hold the[]or
[V]button for more than half a second to 
change frequency rapidly.
When you repeatedly press the []or[V]
button,the frequency change in increments ofFM:100 kHzLW: 9 kHzMW: 9 kHz or 10 kHz
SW: 5 kHzNote:3075m41m21m13m3 
6 
911mM
ENTER
TIME  SETMWSWATSMETERTUNINGMANUAL/AUTO 

 
If you would like to scan the preset stations all inyour mimory. Press M. Scan button the radio will start memory scan from the last station you were and stops for 4 seconds for every preset station then moving forward to next preset station until you press any functional buttons (except POWER and LIGHT) to stop the memory scan.MEMORY SCAN31FWM12345678916m
M.SCAN  

1.Turn on radio by pressing  POWER/SLEEP  
    button. 
2.Select a band.SCAN TUNINGUse scan tuning to rapidly locate a station or to monitor several station within a specific band.32POWER/
   SLEEPAuto tuning systemLWMWSW 

3.Adjust antenna or radio position depending on
   the selected band.
4.Press and hold the []or[V] buttons for more
   than half a  second, the radio will scan all the    frequencies in the Selected band and will stop   automatically each time it lands on an active    station.3375m41m21m13m3 
6 
911mM
ENTER
TIME  SETMWSWATSMETERTUNINGMANUAL/AUTO
AUTO TUNING SYSTEMTUNING POWER/
   SLEEPFINE-STANDBY-TIMERSWMETERTUNINGMANUAL/AUTODISPLAYTIME SETFREQM.SCAN 
MWLWFM
P1/P2...

5.Press and hold the []or[V] button again to 
   resume scanning.When you reach the upper or 
   lower limits of the band, the scanning starts over 
   again as long as the button is depressed.
6.Adjust Volume control for comfortable listening.3475m41m21m13m3 
6 
911mM
ENTER
TIME  SETMwSwATSMETERTUNINGMANUAL/AUTO
VOLUME 

1.Press POWER/SLEEP  button to turn on radio.
2.Tune to any frequency using any of the previous-
    ly mentioned tuning methods.MEMORY TUNING You may store up to 18 presets on FM/SW, and 9 presets on each of the , LW and MW bands for instant 
selection of your favorite stations.STORING A FREQUENCYPOWER/
   SLEEPAuto tuning system
SWM1235 

3.Press the button marked  M (memory), display  
   M  and suggested preset number will flash for 
   12 seconds. If preset 1 and 2 have been stored, 
   it will suggest preset 3 at this stage, on display 
   preset 3 will flash.
  
4.Press  ENTER  button and your station will be
    stored in that memory position.36MTIME  SET
SWM1
SWM12323 

5.Preset positions may be exchanged easily and at 
   any time. Select preset that is to be changed, 
   push memory button,( M  and existing position 
   will flash ) while flashing select new preset posi-
   tion. Presets will be exchanged automatically.
6.FM/SW bands have 18 presets. Presets 1-9 are 
   set in normal manner. When  P1 presets 1-9 are 
   full selecting another station to be preset will 
   display the  P2  display and an additional 1-9 
   presets can be set for a total of 18...

1.If all presets have been used pushing  M  but-
   ton will display  FULL  on LCD. If you still desire 
   to store new station push any button 1-9 where 
   new station is to be positioned  and hold for more 
   than 2 seconds. New station will be put into 
   memory in position selected and original station
    in this position will be canceled.
2.All preset stations are indicated by [    ] on the 
   display. If a station has already been preselected
   it will always show preset position on...

1.Press  POWER/SLEEP  button to turn on radio.
2.Select a band in which a station is stored that 
   you want to recall.RECALLING A PRESET39POWER/
   SLEEPAuto tuning system120m90m75m60m49m41m
1 2 3 
4 5 6 ENTERATSLWMWSWATSATSMETER