Samsung Wf0704w7v User Manual

safety information _11
Do not use natural hand-washing soap for the washer.
- If it hardens and accumulates inside the washer, it may result in problems with the 
product, discolouration, rust or bad odors.
Do not wash large laundry items such as bedding in the washing net.
- Place socks and brassieres into the washing net and wash them with the other laundry.
- Failure to do so may result in injury due to abnormal vibrations.
Do not use hardened detergent.
- If it accumulates inside the washer, it may...

12_ contents
contents
SETTING UP YOUR WASHING 
MACHINE 
13
13   Checking the parts
14   Meeting installation requirements
14  Electrical supply and grounding
14 Water Supply
15 Drain
15 Flooring
15 Surrounding temperature
15 Alcove or closet installation
15   Installing your washing machine
WASHING A LOAD OF LAUNDRY 
21
21   Washing for the first time
21   Basic instructions
22   Using the control panel
25  Child lock
25 Sound off
26 Delay end
26 My cycle
27 Eco Bubble 
28 Washing clothes using the cycle...

setting up your washing machine  _13
01	SETTING	UP
setting up your washing 
machine
Be sure to have your installer follow these instructions closely so that\
 your new 
washing machine works properly and so that you’re not at risk of inju\
ry when doing 
laundry.
CHECKING	THE	PARTS
Carefully unpack your washing machine, and make sure you’ve received all of the parts shown below. 
If your washing machine was damaged during shipping, or if you do not ha\
ve all of the parts, contact 
Samsung Customer...

14_ setting up your washing machine 
setting up your washing 
machine
MEETING	INSTALLATION	REQUIREMENTS
Electrical	supply	and	grounding
Never use an extension cord. 
Use only the power cord that comes with your washing machine.
When preparing for installation, ensure that your power supply offers:
•	AC 220-240V / 50Hz fuse or circuit breaker
•	Individual branch circuit serving only your washing machine
Your washing machine must be grounded. If your washing machine malfunctions or breaks 
down, grounding...

setting up your washing machine  _15
01	SETTING	UP
Drain
Samsung recommends a standpipe height of 65cm. The drain hose must be routed through 
the drain hose clip to the standpipe. The standpipe must be large enough\
 to accept the outside 
diameter of the drain hose. The drain hose is attached at the factory.
Flooring
For best performance, your washing machine must be installed on a solidl\
y constructed floor. 
Wood floors may need to be reinforced to minimize vibration and/or unbalanced loads....

16_ setting up your washing machine 
STEP 2
Removing	the	shipping	bolts
Before installing the washing machine, you must remove all shipping bolts from the back of the 
unit.
1. Loosen all the bolts with the supplied wrench.
2. Hold the bolt with the spanner and pull it through the wide 
section of the hole. Repeat for each bolt.
3. Fill the holes with the supplied plastic covers.
4. Store the shipping bolts away safely in case you have to move the washing ma\
chine in the 
future.
Packaging materials can...

setting up your washing machine  _17
01	SETTING	UP
STEP 3
Adjusting	the	Levelling	feet
When installing your washing machine, ensure that the power plug, the water supply and 
the drain are easily accessible.
1. Slide the washing machine into position.
2. Level your washing 
machine by turning the 
levelling feet in and out as 
necessary by hand. 
3. When your washing machine is level, tighten the nuts using 
the wrench supplied with your washing machine.
STEP 4
Connecting	the	water	and	drain
Connecting...

18_ setting up your washing machine 
setting up your washing 
machine
Connecting the water supply hose
1. Remove the adaptor from the water supply hose.
2. First, using a ‘+’ type screwdriver, loosen the four screws 
on the adaptor. Next, take the adaptor and turn part (2) 
following the arrow until there is a 5 mm gap. 
3. Connect the adaptor to the water tap by tightening the 
screws firmly while lifting the adaptor upwards.  
Turn part (2) following the arrow and connect (1) and (2).
4. Connect the...

setting up your washing machine  _19
01	SETTING	UP
6. Turn on the water supply and ensure that no water leaks 
from the water valve, tap or adaptor. If there is a water 
leaks, repeat the previous steps.
Do not use your washing machine if there is a water leak. 
This may cause electric shock or injury.
•	If the water tap has a screw type tap, connect the water 
supply hose to the tap as shown.
Use the most conventional type of tap for the water supply. In case the \
tap is square or too 
big, remove the...

20_ setting up your washing machine 
setting up your washing 
machine
Connecting the drain hose
The end of the drain hose can be positioned in three ways:
1. Over the edge of a wash basin: The drain hose must be placed at a height of between 60 
and 90 cm. To keep the drain hose spout bent, use the supplied plastic hose guide. S\
ecure 
the guide to the wall with a hook or to the tap with a piece of string t\
o prevent the drain hose 
from moving.
2. ln a sink drain pipe branch: The drain pipe branch...