Samsung UE 37D6500 User Manual

◀▶
English
 
■
Country
 
NThe PIN input screen appears. Enter your 4 digit PIN number.
 
NSelect your country so that the TV can correctly auto-tune the broadcasting 
channels.
 
NThe option may differ depending on country.
 
●Digital Channel: Change the country for digital channels.
 
●Analogue Channel: Change the country for analogue channels.
  

◀◀▶
English
 
■
Auto Tuning
Scans for a channel automatically and stores in the TV.
 
NAutomatically allocated programme numbers may not correspond to actual or 
desired programme numbers. If a channel is locked using the Channel Lock 
function, the PIN input window appears.
 
–Antenna Source: Select the antenna source to memorise. The option may 
differ depending on country.
 
–Channel Type: Select the Channel type to memorise.
 
–Satellite: Selects the satellite to scan. The option may differ depending...

◀▶
English
 
–Automatic Ordering  for italy : Channels found will be automatically ordered 
following a criterion established by all the main national and local tel\
evisions.
 
–Others Ordering  for italy : If you select this menu you will find others 
channels ordering directly organized from private national televisions.
 
NAutomatic Ordering and Others Ordering are available when antenna source 
is set to Air.
 
NThe option may differ depending on country.
  

◀◀▶
English
 
●Cable Search Option
(depending on the country)
Sets additional search options such as the frequency and symbol rate for a 
cable network search.
 
–Freq.Start / Freq.Stop: Set the start or stop frequency (differs in each 
country)
 
–Symbol Rate: Displays available symbol rates.
 
–Modulation: Displays available modulation values.
 
●Standby Auto Store (Off / On)  for Italy : Enables or disables auto-tune while TV is 
in standby mode.
 
●Wake-up Timer (1 hour later / 2 hours later / 00:00...

◀▶
English
 
■
Manual Tuning
Scans for a channel manually and stores in the TV.
 
NIf a channel is locked using the Channel Lock function, the PIN input window 
appears.
 
●Transponder: Selects the transponder using the up/down buttons.
 
●Scan Mode: Selects either free or all channels to store.
 
●Network Search (Disable / Enable): Network search using the up/down 
buttons.
 
●Signal Quality: Display the current status of broadcasting signal.
 
NInformation on a satellite and its transponder is subject...

◀◀▶
English
 
■
Satellite System
The PIN input screen appears. Enter your 4 digit PIN number. Satellite System 
is available when Antenna is set to Satellite. Before running Auto Store, set 
Satellite System. Then channel scan is run normally.
 
●Satellite Selection: You can choose the satellites for this TV.
 
●LNB Power (Off  / On): Enables or disables the power supply for the LNB.
  

◀▶
English
 
●LNB Settings: Configures the outdoor equipment.
 
–Satellite: Selects the satellite for receiving digital broadcasts.
 
–Transponder: Selects a transponder from the list or adds a new 
transponder.
 
–DiSEqC Mode: Selects DiSEqC mode for the selected LNB.
 
–Lower LNB Oscillators: Sets the LNB oscillators to a lower frequency.
 
–Upper LNB Oscillators: Sets the LNB oscillators to a higher frequency.
 
–Tone 22 kHz (Off / On / Auto): Selects the Tone 22 kHz depending on the 
LNB type. For a...

◀◀▶
English
 
●Positioner Settings: Configures the antenna positioner. 
Positioner (On / Off ): Enables or disables the positioned control.
Positioner Type (USALS / DiSEqC 1.2): Sets the positioned type between 
DiSEqC 1.2 and USALS(Universal Satellite Automatic Location System).
 
–My Longitude: Sets the longitude for my location.
 
–My Latitude: Sets the latitude for my location.
 
–Satellite Longitude Settings: Sets the longitude of user defined satellites.
  

◀▶
English
User Mode: Sets the position of satellite antenna according to each satellite. 
If you store the current position of satellite antenna according to a certain 
satellite, when the signal of that satellite is needed, the satellite an\
tenna can be 
moved to pre-populated position.
 
–Satellite: Selects the satellite to set the position for.
 
–Transponder: Selects a transponder from the list for signal reception.
 
–Moving Mode: Selects the movement mode between discrete and 
continuous...

◀◀▶
English
 
–Go to Stored Position: Rotates the antenna to the stored satellite position.
 
–Antenna Position: Adjusts and stores the antenna position for the selected 
satellite.
 
–Store Current Position: Stores current position as the selected positioner 
limit.
 
–Signal Quality: Display the current status of broadcasting signal.