Samsung Ud46cb Manual

131
 •Add on the sub level: Create a sub-group under the selected group.
3 Enter the group name.
Deleting Groups1 Select a group name, and click Edit.
2 In the Edit Group window displayed, click Delete.
3 Click Ye s . The group will be deleted.  

132
Renaming Groups
Rename
1 Select a group name, and click Edit.
2 In the Edit Group window displayed, click Rename.
3 If a cursor appears in the old group name, enter a new group name.
Schedule ManagementCreating Schedules
Create and register a schedule on a group basis.
1 Click All Schedule List in the schedule section on the left side of the program window. The Add button will be enabled 
in the middle.  

133
2 Click the Add button. The Add Schedule window will appear.
3 Click Add below the Device Group item, and select the group you want to add a schedule to.
4 Select Date&Time/Action and click OK. The schedule will be added and a list of schedules will appear in the set\
 list 
window.
 -
Device Group: Select a group.
 -Date&Time
Instant Execution: Run the schedule immediately.
Timer: Set the date, time and interval to run the schedule.
 -Action: Select a function that will activate at the specified...

134
Troubleshooting Guide
 -This program may malfunction 
sometimes due to a communication 
problem between the PC and display 
or electromagnetic waves emitted from 
nearby electronic devices.
Issue Solution
The display you want to control does not 
appear on the system information chart.1 Check the connection of the RS232C cable (check that the cable is properly connected to appropriate serial port).
2 Check that another display with a duplicate ID is not connected. Connecting displays with a duplicate...

135
How display properties are shown when multiple displays are used
1 When no display is selected: The default value is displayed.
2 When one display is selected: Settings for the selected display are displayed.
3 When two displays are selected (e.g. in sequence of ID 1 and ID 3): The settings for ID 1 are displayed before the settings for ID 3.
4 When the All+Select checkbox is checked and all displays are selected: The default settings are displayed.  

136
Troubleshooting Guide
Chapter  10
Requirements Before Contacting Samsung Customer Service Center
Before calling Samsung Customer Service 
Center, test your product as follows. If 
the problem persists, contact Samsung 
Customer Service Center.
Testing the Product
Check if your product is operating normally by using the product test function.
If the screen remains blank while the power LED blinks even when the product is correctly connected to a PC, perform product testing.
1 Power off both the PC and...

137
Check the followings.
Installation issue (PC mode)
The screen keeps switching on and off.Check the cable connection between the product and PC, and ensure the connection is secure.
Blank spaces are found on all four sides of the screen when 
an HDMI or HDMI-DVI cable is connected to the product and 
PC.The blank spaces found on the screen have nothing to do with the product.
Blank spaces on the screen are caused by the PC or graphics card. To resolve the problem, adjust the 
screen size in the HDMI...

138
Screen issue
The screen appears unstable and shaky.Check that the resolution and frequency of the PC and graphics card are set within a range compatible 
with the product. Then, change the screen settings if required by referring to the Additional 
Information on the product menu and the Standard Signal Mode Table.
There are shadows or ghost images left on the screen.
The screen is too bright. The screen is too dark.
Adjust Brightness and Contrast.
Screen color is inconsistent.Go to Picture and...

139
Remote control issue
The remote control does not work.Make sure that the batteries are correctly in place (+/-).
Check if the batteries are flat.
Check for power failure.
Make sure that the power cord is connected.
Check for any special lighting or neon signs switched on in the vicinity.
Source device issue
A beeping sound is heard when my PC is booting.If a beeping sound is heard when your PC is booting, have your PC serviced.  

140
Q & A
QuestionAnswer
How can I change the frequency?Set the frequency on your graphics card.
 •
Windows XP: Go to Control Panel  Appearance and Themes  Display  Settings  
Advanced  Monitor and adjust the frequency in Monitor Settings.
 •
Windows ME/2000: Go to Control Panel  Display  Settings  Advanced  Monitor and 
adjust the frequency in Monitor Settings.
 • Windows Vista: Go to Control Panel  Appearance and Personalization  Personalize  
Display Settings  Advanced Settings  Monitor and adjust the...